Russound KP4 User manual

KP6/KP4 Keypad
The KP6/KP4 keypad is an in-wall Dec ora® style, single-gang
keypad designed for individual zone control of CAA66/CAS44
distributed audio systems {wall plate not included). It has
amber backlit, soft-touch volume, power and source select but-
tons. The KP6 keypad supports the KPSC keypad to add
source control and numeric control capability.
KP6 Keypad Front Panel
.---------.
KP4 Keypad
0 SOURCE NAME - Clear window with replaceable source
name labels. Current source selected is backlit amber.
fJ VOLUME UP - Raises the volume for the room and
adjusts user option features.
IJ SOURCE SELECT - Scrolls through the available sources.
Press and hold brings up the USER MENU for Loudness,
Bass, Treble, etc.
IJ VOLUME DOWN - Lowers the volume for the room and
adjusts user option feature.
EJ IR RECEIVER - Receives IR signals and passes them to
the controller and source equipment. Also used when
the keypad is operated using the CA System remote controls.
D IR CONFIRMATION/LOUDNESS LED - Blue LED blinks to
confirm IR signal reception, and remains lighted when
Loudness feature is enabled.
IJ POWER - Turns room ON or OFF when pressed once;
when OFF, press and hold to turn off all rooms; remains
lit as system indicator.
B VOLUME LEVEL - Volume level indicator LEOs light up
from left to right to indicate volume level. Also indicates
user option adjustments.

KP6/KP4 Side Panel
The KP6 / KP4 OS update jumper and KPSC 12 - pin header are
located on the right side of the keypad (when facing front).
These are covered when a trim plate is installed.
0 OS UPDATE/RUN JUMPER - The pins are jumpered only
when performing an OS update on the keypad , and
removed during normal operation.
fJ KPSC PORT (KP6 only) -12- pin header for connection to
KPSC source control keypad.
IJ OS UPDATE PORT - Used to update the KP6/KP4 keypad
operating system firmware . If an update is released, it
will be available online through the Document Center on
www.russound.com. Look in the "Firmware and
Downloads" section under Multi - Zone product type. The
Advanced Programming Cable is available from
Russound, Part #2500-521065.
0 0 0
CJ
CJ
0 ° 0
KP6 Front View
KP6 Top View
KP6 Side View
OOJ~mpered
~pms
KP6/KP4 Back Panel
The KP6 / KP4 keypad uses a
110-punchdown terminal
on the
back panel to provide a simple
installation
and strong c onnec-
tion for CAT-5 cable's eight con -
ductors.
Punchdown terminals
require the use of a punchdown
tool. Attach the CAT-5 cable to
the 110- punchdown terminal on
the KP6 / KP4 keypad as shown ,
matching
the conductor colors
to
the connection color guide.
The keypad will not operate
properly
if the terminations devi-
ate from the required connec-
tion order.
Take care when using an impact
110
punchdown tool, as th is may
overspread the contact points. Be
sure to use the lowest setting.
Use of the impact tool may propel
stray bits of wire and jacket into
the keypad's chassis and possibly
cause a short in the circu i try.
Gently shake or blow air through
the keypad chassis to remove
stray wire before the keypad is
installed into the junction box.
Keypad Installation
0 0 0
0
C)
0 0
CAT-5 to KP6
Connection
1. Check whether or not you can route the wire to the location
you have chosen.
2. To install a single -gang keypad, you will need to use a
UL / CSA approved plastic si ngle -gang (18 ci) electrical box.
3. Route CAT-5 wire to the junction box from the CA system con-
troller.
4. Use a 110 punchdown tool to connect each wire to its cor-
responding color
labeled on the punchdown terminal.
5. Mount the keypad in the electrical box, add the source name
labels and attach the trim plate.
0
0
~~
~~
~~:
@
@ . • 0
0
Electrical
KP6 Back
Trim
Box Keypad
Plate
Plate

KP6
Keypad
to
CA
Controller Connection
Each
keypad
connects to a
Keypad
Port
on
the
back
of
the
con-
troller
(CAA66
controller
shown
below).
Connections
are
made
using
CAT-5
cable
with
an
RJ45
connector
(wiring
scheme
shown
below).
An
SA-ZX3
Keypad
Splitter
can
be
used
to
add
additional
key-
pads
to
each
zone.
~
__.________,
CAT-S
Cable
KP6
KP6
RJ-45
CAT-S
Wiring
Scheme
""'~
RJ.45
using
T568A
1
Wirin
_g St.1ndard
J
KP6
:~
KP6
Safety Instructions
1.
Read
Instructions
-
All
the
safety
and
operating
instructions
should
be
read
before
the
appliance
is
operated.
2.
Retain
Instructions
-The
safety
and
operating
instructions
should
be
retamed
for
future
reference.
3.
Heed
Warnings
-All
warnings
on
the
appliance
in
the
operating
instruc-
tions
should
be
adhered
to.
4.
Follow
Instructions
-All
operating
and
user
instructions
should
be
fol-
lowed.
5.
Water
and
Moisture-
The
appliance
should
not
be
used
near
water;
for
example,
near
a
bathtub,
washbowl,
kitchen
sink,
laundry
tub,
in
a
wet
basement,
or
near
a
swimming
pool.
6.
Wall
Mounting
-The
appliance
should
be
mounted
to
a
wall
only
as
rec-
ommended
by
the
manufacturer.
7.
Ventilation
-
The
appliance
should
be
situated
so
that
its
location
or
posi-
tion
does
not
interfere
with
its
proper
ventilation.
For
example,
the
appli-
ance
should
not
be
situated
on
a
bed,
sofa,
rug,
or
similar
surface
that
may
block
the
ventilation
openings,
or
placed
in
a
built-in
installation,
such
as
a
bookcase
or
cabinet
that
may
impede
the
flow
of
air
through
the
ventilation
openings.
8. Heat-
The
appliance
should
be
situated
away
from
heat
sources
such
as
radiators,
heat
registers,
stoves,
or
other
appliances
(including
ampli-
fiers)
that
produce
heat.
9.
Power
Sources-
The
appliance
should
be
connected
to
a
power
supply
only
of
the
type
described
in
the
operating
instructions
or
as
marked
on
the
appliance.
10.Grounding
or
Polarization-
Precaution
should
be
taken
so
that
the
grounding
or
polarization
means
of
an
appliance
is
not
defeated.
11.0bject
and
Liquid
Entry
-
Care
should
be
taken
so
that
objects
do
not
fall
and
liquids
are
not
spilled
into
the
enclosure
through
the
openings.
12.Damage
Requiring
Service-
The
appliance
should
be
serviced
by
quali-
fied
service
personnel
when:
A.
Objects
have
fallen,
liquid
has
been
spilled
into
the
appliance;
or
B.
The
appliance
has
been
exposed
to
rain;
or
C.
The
appliance
does
not
appear
to
operate
normally;
or
D.
The
appliance
has
been
dropped
or
the
enclosure
is
damaged.
13.Servicing
-The
user
should
not
attempt
to
service
the
appliance
beyond
that
described
in
the
operating
instructions.
All
other
servicing
should
be
referred
to
qualified
service
personnel.
Precautions:
1.
Power-
WARNING:
BEFORE
TURNING
ON THE
POWER
FOR
THE
FIRST
TIME,
READ
THE
FOLLOWING
SECTION
CAREFULLY.
2.
Do
Not
Touch
The
Unit
With
Wet
Hands-
Do
not
handle
the
unit
when
your
hands
are
wet or
damp.
If
water
or
any
other
liqu
id
enters
the
unit's
cabinet,
take
it
to
a
qualified
service
person
for
inspection.
3.
Care-
From
time
to
time
you
should
wipe
off
the
front
panel
of
the
cabinet
with
a soft
cloth.
Do
not
use
rough
material,
thinners,
alcohol
or
other
chemical
solvents
or
cloths
since
this
may
damage
the
f
inish
or
remove
the
panel
lettering.
ConiOfTll<itO
Ul&SOO
C<'lt
•fiedto
0\NGA

Source Label Installation
Note: Source labels must be inserted prior to installing the trim
plate on the keypad.
1. Determine the system's source names and numbers
(e.g., CD, Source 1).
2. Select the corresponding source name label from the includ-
ed label sheets. Left-side labels are used for sources 1, 3
and 5; right-side labels are used for sources 2, 4 and 6.
3. Slide the label into the window slot until the source name is
centered in the window.
User Options Mode
The User Options Mode allows the user to adjust the audio proper-
ties of a particular zone. The audio features that can be adjusted
are: Bass, Treble, Balance, Turn On Volume and Loudness.
To enter the User Options Mode, press and hold the Source button
when the zone is on. To exit the mode, press and hold the Source
button again (or wait for a 9-second timeout).
The first four source buttons double as indicators for audio feature
selection. When entering the User Options Mode, the top left
l~Russound KP6/KP4 Source Labels
CD 1 CD [__1§_R~ L CABLE 1
CD 2 L Dvg_j l SERVER 2 1 1=- ~~R ]
TAPE !
~ i
! SERVER 3 I
L_______:__ _____ "
DVR
SAT iPod XM 2
(Source 1) button will temporarily blink to indicate "Bass" is ready
for adjustment. Subsequent presses of the Source button toggle
through Treble (Source 2), Balance (Source 3), Turn On Volume
(Source 4), and Loudness (blue LED).
Once an option is selected, the volume up/down buttons are used
to adjust settings. The volume indicator LEOs temporarily light to
indicate the option setting. When Loudness is turned on, the blue
LED lights solid.
Button will blink to indicate the
option that is ready for adjustment
Bass -+-----•
~----.--Treble
tse:RxteR1+4----tr-T urn On
Balance
Option setting level -+---~
Volume
Press Volume
Up or Down
buttons to
adjust setting
r--t ~..,,!Jr~.~~--t- Press and
Blue LED will blink to
indicate Loudness is ready
for adjustment
hold Source
button to
enter or exit
User Options
Mode
Press Source
button to
select option

Technical Specifications
Dimensions: 1.85
11
WX 2. 7
11
0 X 1.4T'H
(4.7 x 6.9 x 3.7 ern)
Fits 1 Gang UL/CSA Approved 18 ci
Junction Box
Weight: 4.0 oz. (113 g)
Power Requirements: 12 VDC 180rnA
CAT-S Connection: 110 punchdown
Warranty Repair
The Russound KP6/4 is fully guaranteed against all defects in materials
and workmanship for two (2) years from the date of purchase. During
this period, Russound will replace any defective parts and correct any
defect in workmanship without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according
to its written instructions. If service is necessary, it must be performed
by Russound. The unit must be returned to Russound at the owner's
expense and with prior written permission. Accidental damage and ship-
ping damage are not considered defects, nor is damage resulting from
abuse or from servicing by an agency or person not specifically author-
ized in writing by Russound.
This Warranty does not cover: Damage caused by abuse, accident, mis-
use, negligence, or improper installation or operation; Power surges and
lightning strikes; Normal wear and maintenance; Products that have
been altered or modified; Any product whose identifying number, decal,
serial number, etc. has been altered, defaced or removed.
Russound sells products only through authorized Dealers and
Distributors to ensure that customers obtain proper support and serv-
ice. Any Russound product purchased from an unauthorized dealer or
other source, including retailers, mail order sellers and online sellers will
not be honored or serviced under existing Russound warranty policy.
Any sale of products by an unauthorized source or other manner not
authorized by Russound shall void the warranty on the applicable prod-
uct.
Damage to or destruction of components due to application of exces-
sive power voids the warranty on those parts. In these cases, repairs
will be made on the basis or the retail value of the parts and labor. To
return for repairs, the unit must be shipped to Russound at the owner's
expense, along with a note explaining the nature of service required. Be
sure to pack the unit in a corrugated container with at least three (3)
inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at [phone] for a
Return Authorization number. Write this number on the shipping label
and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH
03857
Due to continual efforts to improve product quality as new technology
and techniques become available, Russound/FMP, Inc. reserves the right
to revise system specifications without notice.
All trademarks are property of their respective owners.
l. ~Russound®
5 Forbes Road, Newmarket, NH 03857
tel [phone] • fax [phone]
e-mail: [email protected]
www.russound.com
28-1201
07/29/05