Ryobi BCS618 Assembly instructions

18 VOLT NICKEL-CADMIUM/
LITHIUM-ION 6 PORT CHARGER
OPERATORS INSTRUCTION MANUAL
BCS618
N197

DESCRIPTION (See Figures 1-3)
1. BCS618 6-port charger
2. Battery port
3. Blue LED (EnergyStar) power save button
4. Battery port LEDs
5. Protective bumper
6. Carry handle
7. Mounting bracket
8. "Key hole" hanger
9. Screwdriver
10. Screws
11. Pencil
12. Green LED
13. Red LED
14. Charge indicator label
222 mm
381mm
Fig.1
Fig.3
Fig.4
Fig.2
1
78
9
10
10
7
7
11
14
312 13
2
34
5
6

1
English
SAFETY INSTRUCTIONS
CAUTION
When using the battery charger, the following
basic safety precautions should be observed for
protection against electric shock, danger of injury
and burns.
Please read and observe these instructions
before using the device.
Before using the device, check that the mains cable
and mains plug are not damaged.
The device must not be damp, neither should it be
used in a damp environment.
Do not use the device if it has suffered any heavy
shock or jolting, or is damaged in any other way.
Due to the heat generated during charging, the battery
charger should not be operated on a combustible
surface or in an inflammable environment.
Do not cover the ventilating slits.
Never disassemble the device yourself. Danger of
electric shock or fire could be caused by improper
reassembly.
Pull the plug of the battery charger out of the socket
when it is not in use or when cleaning.
Only use an extension cable that is approved and
technically in perfect condition.
During operation, provide sufficient ventilation.
Malfunction during charging can be caused by storing
and operating in places where the temperature
exceeds +40°C; this should be avoided. Battery
charging in closed cupboards, near heat sources
(radiators, bright sunshine) causes heat to accumulate
and can damage the device.
If the battery is not going to be used for a long period,
pull the battery off the battery charger and pull out the
mains plug.
Protect battery contacts from metallic objects to avoid
short circuit which could result in fire or explosion!
Do not rivet or screw any name-plates or signs
onto the device. The protective insulation can
thereby be rendered ineffective. Adhesive labels are
recommended.
Only charge original recommended batteries.
If the power cord is damaged, it must be replaced by
an Authorised Service Center in order to avoid hazard.
WARNING
Do not recharge primary cells (non-
rechargeable).
Damage to property/material
Mains voltage must correspond with the voltage
specifications on the device.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
appliance.
This appliance is not intended for use by young
children or infirm persons unless they have been
adequately supervised by a responsible person to
ensure that they do not play with the appliance.
Keep children and visitors away. Visitors should
wear safety glasses and be kept at a safe distance
from the work area. Do not let visitors contact the tool
or the extension cord.
Complies with AS/NZS 60335.
ASSEMBLY
ASSEMBLING WALL MOUNT BRACKET
See Fig. 2 - 3
Find desired location indoors and away from any
objects that could block vents on the charger. Locate a
wall stud to securely mount the bracket.
You will need two #8 - 63.5mm screws (not included).
Use a level to be sure that bracket is in a vertical
position. Use a pencil to mark the screw hole
placement. Screws should be installed so that the
center distance is 381mm.
Install screws to securely attach bracket.
Place bottom end of charger into the bracket, then
snap the top of charger securely into the bracket.
Charger should fit snugly and securely in the bracket.

2
English
SPECIFICATIONS
Compatible
Battery
Pack
Voltage Charger
Input Chemistry Battery Capacity No. of cell for battery
130109033 18 V 220-240V, 50-60Hz,
AC only Ni-cd 1.5 Ah 15
ABP-1815
ABP1801 1.7 Ah
BPL-1815 Li-ion 1.4 Ah 5
BPL-1820 2.4 Ah 10
RB18L13 1.3 Ah 5
RB18L15 1.5 Ah 5
RB18L26 2.6 Ah 10
RB18L40 4.0 Ah 10
OPERATION
WARNING
Do not allow familiarity with products to make
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING
Always wear safety goggles or safety glasses
with side shields when operating products.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
We recommend that the tool be always
supplied via a residual current device with a
rated residual current of 30 mA or less.
APPLICATIONS
You may use this product for the following purposes:
Charging and maintaining Ryobi One+ 18V battery
packs at peak charge every time (not over time).
CAUTION:
Charge in a well-ventilated area. Do not block
charger vents. Keep them clear to allow proper
ventilation.
CAUTION:
If at any point during the charging process, none
of the LEDs are lit, remove the battery pack from
the charger to avoid damaging the product. DO
NOT insert another battery. Return the charger
and battery to your nearest service center for
service or replacement.
BATTERY PROTECTION FEATURES
Ryobi One+ 18 V Lithium-Ion batteries are designed with
features that protect the Lithium-Ion cells and maximise
battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
NOTE: The LED charge indicator light will not work if the
battery protection feature has caused the battery pack
to stop powering the tool. When the battery pack resets
itself, the LED will again function.
CHARGING THE BATTERY PACK
Use only Ryobi One+ 18V battery packs with
this charger.
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge them until the green LED on the front
of the charger comes on.
Note: The charger will also charge Ryobi One+ 18 V
Ni-Cd battery packs.

3
English
CHARGING A COOL BATTERY PACK
If the charger does not charge the battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Authorised Service Center for
electrical check.
Charge the battery pack only with the charger
provided.
Make sure the power supply is normal household
voltage, 220-240V, 50-60Hz, AC only.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
charger before beginning operation.
Connect the charger to the power supply.
Place the battery pack in the charger aligning the
raised rib on the battery pack with the groove in the
charger.
Press down on the battery pack to be sure contacts
on the battery pack engage properly with contacts in
the charger.
Note: After charging is complete, the green LED will
remain on until the battery pack is removed from the
charger or charger is disconnected from the power supply.
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
Do not place the charger and battery pack in an area
of extreme heat or cold. They will work best at normal
room temperature.
Note: The charger and battery pack should be placed
in a location where the temperature is more than
10°C but less than 38°C.
When batteries become fully charged, it is suggested
to unplug the charger from the power supply and
remove the battery pack.
To remove the battery pack from the charger, depress
the latches on each side of the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the batteries in the
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
Note: This situation only occurs when continuously
using a tool which causes the batteries to become hot.
It does not occur under normal circumstances. Refer
to "CHARGING A COOL BATTERY PACK" for normal
recharging of batteries. If the charger does not charge
your battery pack under normal circumstances, return
both the battery pack and charger to your nearest
Authorised Service Center for electrical check.
BLUE LED (ENERGYSTAR) STATUS BUTTON
Charger has blue LED status button to indicate power on.
BLUE LED STATUS BUTTON
100%
0% FULL BRIGHTNESS
LED maintains full and constant brightness - batteries
are charging.
100%
0% SLOW PULSE
LED shows a slow pulse - batteries are in mainte-
nance mode.
100%
0% WAVE PULSE
LED produces fluctuating pulse – charger is in energy
save mode. Batteries are neither charging nor being
maintained.
When batteries are charging, the blue LED status
button will maintain a full and constant brightness.
Whilebatteriesareinmaintenancemode,theblueLED
status button will slowly pulse. When maintenance
mode is complete, charger goes into energy save
mode.
Blue LED status button will maintain a fluctuating
pulse while in energy save mode. Batteries are not
being charged or maintained; the charger does not
hold any batteries.
NOTE: Battery port LEDs will turn off during maintenance
mode and energy save mode.
Charger awakens from energy save mode when
status button is pressed or automatically after 5 days
in energy save mode.
BATTERY PORT LEDS
Red LED on, Green LED off = Battery installed.
Red LED flashing, Green LED off = Battery is being
tested.
Red LED on, Green LED flashing = Battery is charging.
Red LED off, Green LED on = Battery is fully charged.
Red LED flashing, Green LED flashing, simultaneously
= Battery is defective.
Red LED flashing, Green LED flashing, alternating =
Battery port is defective.

4
English
MAINTENANCE AND REPAIRS
Risk of injury
Service, testing and repairs should only be carried
out by authorised service centres.
We recommend our customer service department or
authorised service centres.
STORAGE
Store your charger in a cool dry place between 10 &
25°C. It is not recommended to leave it in a cold works
van overnight. Ensure no metal filings or swarf can fall
into the vents during storage, as this may cause serious
injury when it is next used.
LED FUNCTIONS OF CHARGER
See Fig. 4.
LED FUNCTIONS
BATTERY PACK RED LED GREEN LED ACTION
Power
Without battery pack ON OFF Ready to charge battery pack.
Evaluate
Hot battery pack Flashing OFF When battery pack reaches cooled temperature, charger begins fast charge mode.
Cold battery pack Flashing OFF When battery pack reaches warmed temperature, charger begins fast charge mode.
Deeply discharged Flashing OFF Charger pre-charges battery until normal voltage is reached, then begins fast charge mode.
Defective
Defective Flashing Flashing Battery pack or charger is defective.
• If defective, try to repeat the conditions a second time by removing and reinstalling the battery pack. If the LED status repeats a
second time, try charging a different battery.
• If a different battery charges normally, dispose of the defective pack (see Maintenance section).
• If a different battery also indicates “Defective,” the charger may be defective.
Charging
Fast charging ON Flashing
Full
OFF ON Fast charging is complete; charger maintains charge mode.
Port Error
Without
battery pack Flashing Flashing Red LED flashing, Green LED flashing , alternating — battery port is defective.

961152038-01B
Techtronic Industries (Australia) Pty. Ltd.
Level 1, 660 Doncaster Road
Doncaster, VIC 3108, Australia
Techtronic Industries New Zealand Ltd.
27 Clemow Drive
Mt. Wellington,Auckland 1060, New Zealand