Safe Fleet PRIME DESIGN UXV 211 User manual



2
2
3
1
4
5
UXV-211 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
1—Rear Rotation Assembly................................... (Qty 1)
2—Front Rotation Assembly .................................. (Qty 1)
ELR-8112 Tele scope handle
ELR-8082 Adj Z post
ELR-7225
ELR-8151 left rear handle
assembly
ELR-8151 left rear handle
assembly
ELR-8151 Rear handle
Assembly
ELR-7049 Vertical
Rotational Arm
ELR-7038 Vertical drive arm
ELR-7558 Vertical Upper Gen 4
ACL-125



3
UXV-211 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
3—Rear Drive Shaft ............................................... (Qty 1)
Right Hand, 50.00”
HKT-8102-Rotation Hardware Kit
Mounting Hardware
5—Front Drive Shaft .............................................. (Qty 1)
B Version, 35.75”
4—Connecting Bar ................................................. (Qty 1)
48.00”
Anti-Seize (1X)
Lubricant (1X)
Clevis Pin (1X)Cotter Pin (1X)
M8 x 50MM (4X) 

Stickers (10X)
M8 Lock Nut (4X)  
M8 Lock Nut (8X)
M8 x 30MM (8X)
 
ELR-1119 Hinge block
ELR-8525 Trigger latch
ELR-8151 left rear handle
assembly
ELR-8204 connecting rod
ELR-8061 Adj front drive shaft



4
UXV-211 ASSEMBLY INSTRUCTIONS–MOUNTING TO UTILITY BODY
M8 x 30MM Bolt
Sealing Washer
Mounting
Utility Body
Neoprene Washer
Fender Washer
M8 Locknut
Mounting Hardware (8X)
96.00”
84.00”
72.00”
96.00”
84.00”
72.00”
Rear Lower
Front Lower
3.50”3.50”
UTILITY BODY MOUNTING
6.00-8.00 Ft: Drill holes into the Service Body
mounting location according to dimensions shown.
0.1
0.4 Torque to 90 in-lbs
0.3
Using the fastening hardware shown below,
attach the vertical Uprights to the Utility Body.

Locknut install from the inside of the Utility
Body in the order shown, while the Bolt and

0.2 Position and align the vertical
Uprights until the mounting holes
realign to the body holes drilled
during Steps 0.1.



5
3
1
2/6
4
7
5
RIGHT ROTATION ASSEMBLY SEQUENCE
UXV-211 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
REAR DRIVE SHAFT
1.1
1.3
1.5
Torque to 90 in-lbs
1.4
1.2



6
UXV-211 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
CYLINDER HARDWARE CONNECTING BAR
2.1
2.2
3.1
3.2
CONNECTING BAR FASTENERSFRONT DRIVE SHAFT
5
4.4
Torque to 90 in-lbs
4.3
4.2
4.1



7
DRIVE SHAFT SEALING
Apply Silicone Sealant
to Connecting Bar ends
Adjust the Cylinder Flow
Control Screw to allow
approximately 3 seconds
time for the ladder to glide
down when operating the
loaded Ladder Rack.
6
CYLINDER ADJUSTMENT
7.1
7.2
UXV-211 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
For additional information regarding your UXV-211 Ladder Rack,
please visit the Prime Design website at: www.primedesign.net.
Using a QR code reader in your smart phone or tablet, read the QR
Code shown below and follow the same steps as you would from your
laptop or computer.
If you’re viewing this document as an interactive PDF, you may simply
click on the QR Code below to access the Prime Design website.
ADDITIONAL INFORMATION

USAM-UXV211-US01 Rev-B 1116