Safe Fleet Prime Design FBM-1029 User manual

Page 2 Packaging Contents
Pages 3-6 Utility Roof Mountings
Utility Roof Mount Frame Base Mounting Kit
PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118
Toll Free: 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
2
Foam Pad (4X)Mounting Bracket (4X)
Sealing
Washer (8X) Lock Nut (8X)
M8 x 45MM (8X)M8 x 35MM (8X)
Neoprene
Washer (8X)
Fender Washer (8X)
FBM-1029 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—FBM-1029......................................................... (Qty 1)
Utility Roof Mounts, with HKT-8266
CONTENTS OVERVIEW
2—Gen4 Crossbars (not shown above)................ (Qty 1)
Ordered separately, Front & Rear, 84”–96”
NOTE: The M8 x 35MM and M8 x 45MM Mounting
Bolts are available in the HKT-8266 Hardware Kit for
varying mounting surfaces and thickness.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
3
FBM-1029 ASSEMBLY INSTRUCTIONS–UTILITY ROOF MOUNTINGS
Rear
Front
M8 x 35MM
Sealing Washer
Foam Pad
Neoprene Washer
Fender Washer
M8 Lock Nut
Set according to vehicle or cap
manufacturer’s recommened
mounting positions
72.00”–96.00”
5.00”
Rear Drive Shaft Offset
31.75” (approx.)
UTILITY ROOF MOUNTINGS
MOUNTING BRACKETS TO ROOF 1.2 Assemble unto vehicle roof as shown, then torque the Mounting
Feet nuts to 130 in-lbs.
1.1 Drill bolt holes according to the dimensions shown.
NOTE: The Rear Drive Shaft must
not extend past the bumper of
your vehicle. See Rear Drive
Shaft Offset below for reference
while placing your rack.
Do not mount the Crossbars to this FBM system at this time.
Refer to the respective FEA or AR Assembly Manual(s)
included with your chosen rack conguration features.
Depending upon the features chosen, you may need to
perform a complete feature assembly onto the Crossbars or
Side Rails as noted in that feature’s Assembly Manual.
WARNING: Failure to position the Crossbars as shown in this
FBM Assembly Manual may result in damage to the sliding
door and/or ladder rack.
NOTE: Crossbars, Side Rails, Base, Clamp Down, or Rotation
features are not included in this FBM kit, and must be
purchased separately. To purchase applicable features and
accessories, please contact your authorized distributor, or a
Prime Design Sales & Service Representative.
NOTE: The M8 x 45MM
Mounting Bolt options
are available in the
HKT-8266 Hardware
Kit as needed for thicker
mounting surfaces.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
4
Even
Even
Even
Even
Front
Rear
FBM-1029 ASSEMBLY INSTRUCTIONS–MOUNTING TO CROSSBARS
USAM-FBM1029-US01 Rev-A 0720
FBM ASSEMBLY SEQUENCE
NOTE: LH/RH Rotation and Crossbar
features are shown for illustrative
purposes only. These features are not
included with this Base Mounting Kit,
and must be purchased separately.
2.1
CROSSBARS
2.2
Torque all
Crossbar Clamp
nuts to 90 in-lbs
Shown with LH/RH Rotation
for illustrative purposes only
CROSSBAR ADJUSTMENT