Samson 3349 Service manual

Translation of original instructions
EB 8048-21 EN
53-06
Edition March 2022
Type3349 Aseptic Angle Valve with USP-VI diaphragm
In combination with an actuator, e.g. a SAMSON Type3271 or
Type3277 Pneumatic Actuator or Type3379 Pneumatic Actuator
Note: This version of the
product is to be discontinued
shortly.
Replacement device:
Type3349HV01
These mounting and operating
instructions will then only apply
to valves already in use.
The mounting and operating
instructions uEB8048-2
apply to the Type3349HV01.
They can be downloaded from
our website at
uwww.samsongroup.com >
Service & Support >
Downloads > Documentation
Type3349 Valve with Type3277 Pneumatic
Actuator and Type3730 Positioner
Type3349/3379 Control Valve with
Type3724 Positioner

Definition of signal words
Hazardous situations which, if not avoided,
will result in death or serious injury
Hazardous situations which, if not avoided,
could result in death or serious injury
Property damage message or malfunction
Additional information
Recommended action
DANGER
!
WARNING
!
NOTICE
!
Note
Tip
EB 8048-21 EN
Note on these mounting and operating instructions
These mounting and operating instructions assist you in mounting and operating the device
safely. The instructions are binding for handling SAMSON devices. The images shown in
these instructions are for illustration purposes only. The actual product may vary.
ÎFor the safe and proper use of these instructions, read them carefully and keep them for
later reference.
ÎIf you have any questions about these instructions, contact SAMSON‘s After-sales Service
([e-mail]).
Documents relating to the device, such as the mounting and operating
instructions, are available on our website at www.samsongroup.com >
Service & Support > Downloads > Documentation.

Contents
EB 8048-21 EN
1 Safety instructions and measures ...................................................................5
1.1 Notes on possible severe personal injury .........................................................8
1.2 Notes on possible personal injury ...................................................................8
1.3 Notes on possible property damage..............................................................10
2 Markings on the device ...............................................................................12
2.1 Body inscription...........................................................................................12
2.2 Actuator nameplate......................................................................................12
2.3 Material identication number ......................................................................12
3 Design and principle of operation ................................................................14
3.1 Fail-safe positions ........................................................................................14
3.2 Versions ......................................................................................................17
3.3 Technical data .............................................................................................18
4 Shipment and on-site transport ....................................................................22
4.1 Accepting the delivered goods ......................................................................22
4.2 Removing the packaging from the valve.........................................................22
4.3 Transporting and lifting the valve...................................................................22
4.3.1 Transporting the valve ..................................................................................23
4.3.2 Lifting the valve............................................................................................24
4.4 Storing the valve..........................................................................................26
5 Installation..................................................................................................27
5.1 Installation conditions...................................................................................27
5.2 Preparation for installation............................................................................28
5.3 Mounting the device.....................................................................................29
5.3.1 Mounting the actuator onto the valve.............................................................30
5.4 Installing the valve into the pipeline ...............................................................32
5.5 Testing the installed valve..............................................................................32
5.5.1 Leak test......................................................................................................34
5.5.2 Travel motion...............................................................................................34
5.5.3 Fail-safe position..........................................................................................34
5.5.4 Pressure test.................................................................................................34
6 Start-up ......................................................................................................35
7 Operation...................................................................................................36
8.1 Troubleshooting ...........................................................................................38
7.1 CIP (cleaning-in-place) .................................................................................38
7.2 SIP (sterilization-in-place) .............................................................................38

Contents
EB 8048-21 EN
8 Malfunctions ...............................................................................................38
8.2 Emergency action ........................................................................................39
9 Servicing.....................................................................................................40
9.1 Checking the extent of servicing ....................................................................42
9.2 Preparing the valve for service work ..............................................................42
9.3 Installing the valve after service work.............................................................42
9.4 Service work for version with Type3271 or Type3277 Actuator......................42
9.4.1 Replacing the packing..................................................................................43
9.4.2 Replacing the diaphragm and plug ...............................................................43
9.5 Service work for version with Type3379 Actuator ..........................................46
9.5.1 Replacing the packing..................................................................................46
9.5.2 Replacing the diaphragm and plug ...............................................................47
9.6 Checking the concentricity of the plug to the plug stem....................................50
9.7 Ordering spare parts and operating supplies .................................................50
10 Decommissioning ........................................................................................51
11 Removal .....................................................................................................53
11.1 Removing the valve from the pipeline.............................................................53
11.2 Removing the actuator from the valve ............................................................54
12 Repairs .......................................................................................................54
12.1 Returning devices to SAMSON .....................................................................54
13 Disposal......................................................................................................55
14 Annex.........................................................................................................56
14.1 After-sales service........................................................................................56
14.2 Certicates ..................................................................................................56
14.3 Spare parts .................................................................................................60

EB 8048-21 EN 5
Safety instructions and measures
1 Safety instructions and measures
Intended use
The SAMSON Type3349 Angle Valve in combination with an actuator (e.g. Type3271,
Type3277 or Type3379 Pneumatic Actuator) is designed to regulate the ow rate, pressure
or temperature of liquids, gases or vapors. The angle valve is suitable for use in aseptic ap-
plications (e.g. in the pharmaceutical and food industries).
The valve with its actuator is designed to operate under exactly dened conditions (e.g.
operating pressure, process medium, temperature). Therefore, operators must ensure that the
control valve is only used in operating conditions that meet the specications used for sizing
the valve at the ordering stage. In case operators intend to use the control valve in
applications or conditions other than those specied, contact SAMSON.
SAMSON does not assume any liability for damage resulting from the failure to use the de-
vice for its intended purpose or for damage caused by external forces or any other external
factors.
ÎRefer to the technical data and nameplate for limits and elds of application as well as
possible uses.
Reasonably foreseeable misuse
The control valve is not suitable for the following applications:
− Use outside the limits dened during sizing and by the technical data
− Use outside the limits dened by the valve accessories connected to the valve
Furthermore, the following activities do not comply with the intended use:
− Use of non-original spare parts
− Performing service and repair work not described
Qualications of operating personnel
The control valve must be mounted, started up, serviced and repaired by fully trained and
qualied personnel only; the accepted industry codes and practices must be observed.
According to these mounting and operating instructions, trained personnel refers to
individuals who are able to judge the work they are assigned to and recognize possible
hazards due to their specialized training, their knowledge and experience as well as their
knowledge of the applicable standards.
Welding operations must only be performed by personnel who has the necessary qualica-
tion to perform the applied welding procedure and handle the materials used.

6 EB 8048-21 EN
Safety instructions and measures
Personal protective equipment
We recommend checking the hazards posed by the process medium being used (e.g.
uGESTIS (CLP) hazardous substances database). Depending on the process medium and/
or the activity, the protective equipment required includes:
− Protective clothing, gloves, eye protection and respiratory protection in applications with
hot, cold and/or corrosive media
− Wear hearing protection when working near the valve
− Hard hat
− Safety harness when working at height
− Safety footwear, ESD (electrostatic discharge) footwear, if necessary
ÎCheck with the plant operator for details on further protective equipment.
Revisions and other modications
Revisions, conversions or other modications of the product are not authorized by SAMSON.
They are performed at the user's own risk and may lead to safety hazards, for example.
Furthermore, the product may no longer meet the requirements for its intended use.
Safety devices
Upon supply air or control signal failure, the valve moves to its fail-safe position (see
section3.1). The fail-safe action of the actuator is the same as its direction of action and is
specied on the nameplate of SAMSON actuators (see actuator documentation).
Warning against residual hazards
To avoid personal injury or property damage, plant operators and operating personnel must
prevent hazards that could be caused in the control valve by the process medium, the operat-
ing pressure, the signal pressure or by moving parts by taking appropriate precautions. Plant
operators and operating personnel must observe all hazard statements, warning and caution
notes in these mounting and operating instructions.
Hazards resulting from the special working conditions at the installation site of the valve must
be identied in a risk assessment and prevented through the corresponding safety instruc-
tions drawn up by the operator.

EB 8048-21 EN 7
Safety instructions and measures
Responsibilities of the operator
Operators are responsible for proper use and compliance with the safety regulations.
Operators are obliged to provide these mounting and operating instructions as well as the
referenced documents to the operating personnel and to instruct them in proper operation.
Furthermore, operators must ensure that operating personnel or third parties are not exposed
to any danger.
Operators are additionally responsible for ensuring that the limits for the product dened in
the technical data are observed. This also applies to the start-up and shutdown procedures.
Start-up and shutdown procedures fall within the scope of the operator's duties and, as such,
are not part of these mounting and operating instructions. SAMSON is unable to make any
statements about these procedures since the operative details (e.g. differential pressures and
temperatures) vary in each individual case and are only known to the operator.
Responsibilities of operating personnel
Operating personnel must read and understand these mounting and operating instructions as
well as the referenced documents and observe the specied hazard statements, warnings
and caution notes. Furthermore, operating personnel must be familiar with the applicable
health, safety and accident prevention regulations and comply with them.
Referenced standards, directives and regulations
The control valves meet the requirements in the Regulation (EC) No.1935/2004 for materi-
als and articles intended to come into contact with food
The control valves comply with the requirements of the European Pressure Equipment Direc-
tive 2014/68/EU and the Machinery Directive 2006/42/EC. Valves with a CE marking
have a declaration of conformity which includes information about the applied conformity
assessment procedure. This declaration of conformity is included in the annex of these in-
structions (see section14.2).
According to the ignition hazard assessment performed in accordance with Clause5.2 of
ISO80079-36, the non-electrical control valves do not have their own potential ignition
source even in the rare incident of an operating fault. As a result, they do not fall within the
scope of Directive 2014/34/EU.
ÎFor connection to the equipotential bonding system, observe the requirements specied in
Clause6.4 of EN60079-14 (VDE0165-1).

8 EB 8048-21 EN
Safety instructions and measures
Referenced documentation
The following documents apply in addition to these mounting and operating instructions:
− Mounting and operating instructions for mounted actuator, e.g. uEB8310-X for
Type3271 and Type3277 Actuators or uEB8315 for Type3379 Actuator
− Mounting and operating instructions for mounted valve accessories (positioner, solenoid
valve etc.), for example uEB8395 for Type3724 Positioner
− uAB0100 for tools, tightening torques and lubricant
− Manual uH02: Appropriate Machinery Components for SAMSON Pneumatic Control
Valves with a Declaration of Conformity of Final Machinery
1.1 Notes on possible severe personal injury
DANGER
!
Risk of bursting in pressure equipment.
Valves and pipelines are pressure equipment. Impermissible pressure or improper
opening can lead to valve components bursting.
ÎObserve the maximum permissible pressure for valve and plant.
ÎBefore starting any work on the control valve, depressurize all plant sections affect-
ed as well as the valve.
ÎDrain the process medium from all the plant sections concerned as well as the
valve.
1.2 Notes on possible personal injury
WARNING
!
Risk of burn injuries due to hot or cold components and pipelines.
Depending on the process medium, valve components and pipelines may get very hot
or cold and cause burn injuries.
ÎAllow components and pipelines to cool down or warm up to the ambient tempera-
ture.
ÎWear protective clothing and safety gloves.

EB 8048-21 EN 9
Safety instructions and measures
WARNING
!
Risk of hearing loss or deafness due to loud noise.
The noise emissions depend on the valve version, plant facilities and process medium.
ÎWear hearing protection when working near the valve.
Risk of personal injury due to exhaust air being vented.
While the valve is operating, air is vented from the actuator, for example, during
closed-loop operation or when the valve opens or closes.
ÎInstall the control valve in such a way that vent openings are not located at eye level
and the actuator does not vent at eye level in the work position.
ÎUse suitable silencers and vent plugs.
ÎWear eye protection when working in close proximity to the control valve.
Crush hazard arising from moving parts.
The pneumatic control valves with Type3271 and Type3277 Actuator contain moving
parts (actuator and plug stem), which can injure hands or ngers if inserted into the
valve.
ÎDo not insert hands or nger into the yoke while the air supply is connected to the
actuator.
ÎBefore working on the control valve, disconnect and lock the pneumatic air supply
as well as the control signal.
ÎDo not impede the movement of the actuator and plug stem by inserting objects into
the yoke.
ÎBefore unblocking the actuator and plug stem after they have become blocked (e.g.
due to seizing up after remaining in the same position for a long time), release any
stored energy in the actuator (e.g. spring compression). See associated actuator
documentation.
Risk of personal injury due to preloaded springs.
Valves in combination with pneumatic actuators with preloaded springs are under ten-
sion. These control valves with SAMSON pneumatic actuators can be identied by the
long bolts protruding from the bottom of the actuator.
ÎBefore starting any work on the actuator, relieve the compression from the preload-
ed springs (see associated actuator documentation).

10 EB 8048-21 EN
Safety instructions and measures
WARNING
!
Risk of personal injury due to residual process medium in the valve.
While working on the valve, residual medium can ow out of the valve and, depending
on its properties, cause personal injury, e.g. (chemical) burns.
ÎIf possible, drain the process medium from all the plant sections affected and the
valve.
ÎWear protective clothing, safety gloves, respiratory protection and eye protection.
Risk of personal injury through incorrect operation, use or installation as a result of
information on the valve being illegible.
Over time, markings, labels and nameplates on the valve may become covered with dirt
or become illegible in some other way. As a result, hazards may go unnoticed and the
necessary instructions not followed. There is a risk of personal injury.
ÎKeep all relevant markings and inscriptions on the device in a constantly legible
state.
ÎImmediately renew damaged, missing or incorrect nameplates or labels.
1.3 Notes on possible property damage
NOTICE
!
Risk of valve damage due to contamination (e.g. solid particles) in the pipeline.
The plant operator is responsible for cleaning the pipelines in the plant.
ÎFlush the pipelines before start-up.
Risk of valve damage due to unsuitable medium properties.
The valve is designed for a process medium with dened properties.
ÎOnly use the process medium specied for sizing the equipment.
Risk of leakage and valve damage due to excessively high or low tightening torques.
Observe the specied torques when tightening control valve components. Excessive
tightening torques lead to parts wearing out more quickly. Parts that are too loose may
cause leakage.
ÎObserve the specied tightening torques (uAB0100).