Samsung SDS-P4040 User manual

Samsung All-in-One CCTV
(SDS-P3040, SDS-P4040)
Remote Viewing Setup Guide
1

DVR Network Setting
Please follow the steps from Quick Start Guide included in the CCTV kits.
This set up guide is only for remote viewing setting for DVR andADSL or LTE Router
❒ADSL or 3G/LTE Router (Gateway) IP check
1. Find the IP address of router
- Default router IP address is written at the bottom or back side of router usually.
If you cannot get the IP address of router please follow the below step with PC which is
connected to the router
If the PC is connected properly to the internet, the <Default Gateway> IP address is the
Router’s IP address. Please record the Gateway IP address below.
Default Gateway (Router IP) : 2

DVR Network Setting
❒Connection Mode
1. Please make sure LAN cable is connected properly from DVR to WiFi router and internet is
working.
2. Click on Network and select <Connection Mode>.
3. Select <Static IP>
4. Enter the <IP>
The IP address consists of 4 fields, and the first 3 fields should be same to those of <Default Gateway>
address of your computer which you wrote down previous page, and the last field should be
unoccupied number (between 2 and 254)
ex) When <Default Gateway> is 192.168.1.1, the DVR <IP> can be 192.168.1.200
The first 3 fields should follow Default Gateway IP and 4th field can be fixed to 200
(any number between 2~254 which is not occupied by other device)
5. Enter the <Gateway> and <Subnet Mask> as same to those of your computer found in
previous page
※In ADSL or 3G/LTE Router setting, Gateway is the IP address of Router which you checked in
previous page.
Please leave subnet mask as default (255.255.255.0) in most cases.
3

DVR Network Setting
6. Leave Protocol setting as default if you don’t have multiple DVR or any webserver in your network.
※If you already have other DVR or Webserver which is already using same <Webviewer Port> (80)
or <TCP port> (4520 ~ 4524), the port need to be changed. In this case, please follow the steps from
page 5 of “Router Setup Guide” which is included in the CD Rom from Samsung CCTV kit.
4

DVR Network Setting
5

1. From network tab, click <DDNS>
2. Under DDNS Site, select <iPOLis>
3. Under <Product ID>, enter the Product ID
which is registered at samsungipolis.com
※Product ID should be pre registered at
samsungipolis.com
8. Select Use under Quick Connect
9. Select OK
DVR Network Setting
❒DVR DDNS Setting
Go back to DVR
6

Remote Viewing Setting
❒For Android Phone
Name: Create a name for the DVR
e.g.) Home_DDNS
Model: Select DVR
Address Type : Select DDNS
Host : enter DDNS host address. It should be
www.samsungipolis.com/Product ID
※Product ID is what you input at DVR DDNS
menu
HTTP Port : Input 80
RSTP Port: Input 4524
ID : Input admin
Password : Input DVR password
Select Save
❒Add Device for 3G/4G connection
❒For iPhone
7
※When the app cannot be connected to DVR properly, please follow the step in Router Setup (Page 10)

Remote Viewing Setting
This setting is for when Smart Phone is
connected to Telkom WiFi router
Name: Create a name for the DVR
e.g.) Home_IP
Model: Select DVR
Address Type : Select IP
IP : Input 192.168.1.200
HTTP Port : Input 80
RSTP Port: Input 4524
ID : Input admin
Password : Input DVR password
Select Save
❒Add Device for WiFi setting
8

Remote Viewing Setting
1. Open Internet Explorer and go to http://192.168.1.200
2. You will be asked to install the active X plug-in for internet explorer.
3. Login with user ID and password for the DVR
❒For PC connected to same router with DVR
1. Open Internet Explorer and go to http://www.samsungipolis.com/product ID
Product ID is what you input at DVR DDNS menu
2. Login with user ID and password for the DVR
※Web browser viewing only support Internet Explorer.
❒For remote PC outside of home
e.g.) telkom001, telkom002
※Product ID should be pre registered at samsungipolis.com
9

Router Setting
1. Connect to http://192.168.1.1 using web
browser from PC which are already
connected to Telkom router (Huawei B593)
※default Admin password is ‘admin’.
If not, please ask to customer.
2. Select NAT Settings
3. Select Port Mapping under NAT Settings
4. Select Add Item
5. Select TCP/UDP under Protocol
6. Input 80 under Remote Port Range
7. Input DVR IP 192.168.1.200 under Local Host
8. Input 80 under Local Port
9. Select Submit
10. Repeat steps from 4 to 9 with only changing port number in Remote Port Range
and Local Port and register all below ports for DVR
- 4520, 4521, 4522, 4523, 4524
11. After register all ports, port mapping status will be like below
10
※For most of routers which support UPnP (Universal Plug and Play), do not need this Router
Setting step. If remote viewing is not working properly from your mobile device, please check the
internet connectivity of your router first and check the UPnP setting of your router first.
This below Port Forwarding is required for some of routers including Huawei LTE router.
Below step is based on Huawei B594 LTE router. For other models, please follow the Port
Forwarding setting guide from the “Router Guide” in the CD Rom inside of Samsung CCTV Kit.

Manufactured by
Distributed by
Block 2│Thornhill Office Park│94 Bekker Rd│Midrand
Postnet suite 1300│Private Bag X153│Bryanston 2021
T [phone]│F [phone]│www.3dr.co.za