Samsung DCS Owner's manual

SAMSUNG
COMBINED
PROGRAMMING
MANUAL
for
DCS
DCS COMPACT
DCS COMPACT II
DCS-816
DCS-408
DCS-408i
DCS

Publication Information
Samsung Telecoms reserves the right without prior notice to revise information in
this publication for any reason.
Samsung Telecoms also reserves the right without prior notice to make changes in
design or components of equipment as engineering and manufacturing may warrant.
Disclaimer
Samsung Telecoms is not responsible for errors or problems arising from customers
not installing, programming or operating their Samsung systems as described in this
manual.
Copyright 2001
Samsung Telecoms (UK) Limited
All rights reserved. No part of this manual may be reproduced in any form or by any
means –graphic, electronic or mechanical, including recording, taping, photocopy or
information retrieval system –without express written permission of the publisher of
this material.
Part No.:12623 Version 2.0

EU Declaration of Conformity
For other directives relevant to DCS Compact II, DCS-816, DCS-408 and DCS-408i systems,
refer to the Samsung website at:
www.samsung-telecoms.co.uk

DCS CONTENTS
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
Contents
Part
1Introduction to Programming .....................................1–1
1.1 Using this Manual...........................................................................1–1
1.2 ProgrammingOverview..................................................................1–2
1.3 Programming Levels......................................................................1–2
1.3.1 System Level ............................................................................ 1–2
1.3.2 Customer Level......................................................................... 1–2
1.3.3 Station Level............................................................................. 1–3
1.4 Keys Used for Programming..........................................................1–3
1.4.1 Soft Keys.................................................................................. 1–3
1.4.2 Other Keys ............................................................................... 1–3
1.5 Programming Procedures..............................................................1–4
1.5.1 Precautions When Programming ............................................... 1–4
1.5.2 Opening System or Customer Level Programming ..................... 1–4
1.5.3 Opening Station Level Programming.......................................... 1–5
1.5.4 Programming DCS-408 and 408i Systems.................................. 1–5
2Program (MMC) List and Default Data......................2–1
2.1 Program (MMC) List.......................................................................2–1
2.2 DefaultData....................................................................................2–3
2.3 System Configuration: Quick Reference...................................... 2–9
3Special Applications ....................................................3–1
Voice Mail / Auto Attendant Integration...................................................3–2
Individual Station Page............................................................................3–4
CLIP (Calling Line Identification Presentation)........................................3–5
Toll Restriction (Call Barring) Overview...................................................3–6
S0 Overview.............................................................................................3–8
4MMCs (in numerical order) ........................................4–1

DCS INTRODUCTION
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
1-1
Part 1. Introduction to Programming
This manual describes the MMC programming required for the following types of Sam-
sung DCS keyphone system:
•DCS
•DCS Compact (Compact I)
•DCS Compact II
•DCS-816
•DCS-408
•DCS-408i.
In this manual, these systems are referred to as “DCS,” “Compact I (CI),” “Compact II
(CII)," "816," "408" and “408i” respectively. Programming requirements for these system
types are generally the same, but occasionally there are differences. Users of 408 and
408i systems should also read Programming DCS-408 and 408i Systems in section 1.5.4
of this manual. Unless otherwise stated, references to “DCS” include Compact I sys-
tems.
The different system types are discussed fully in the separate Samsung General De-
scriptionmanuals for each system, where these have been published.
Software Version Numbers
The software version numbers of the systems for which this programming manual is
relevant are: DCS and Compact II=V6.10 or later; 816=V1.09 or later; 408 and
408i=1.04 or later.
1.1 Using This Manual
•It is recommended that you read the whole of Part 1 of this manual which provides a
useful overview to MMC programming procedures.
•For a comprehensive list of available MMCs, see Part 2.
•For quick reference, Part 2 also provides a table listing the default settings for each
MMC and indicating which systems can use each MMC. A “Y” (“Yes”) in the appro-
priate column indicates that it can be used for that system.
•To quickly check allowed configuration settings for each type of system—number of
trunk group members, card port numbers, and so on—see section 2.3 System Con-
figuration: Quick Reference in Part 2.
•To begin programming, refer to the appropriate MMC(s) in Part 4. Check the se-
lected MMC header bar to make sure the program is available on your system, if
you haven’t already done so.
•Refer to Part 3, Special Applications, for further information on voice mail / auto at-
tendant integration, individual station paging, CLIP (Calling Line Identification Pres-
entation), toll restriction (call barring) and S0programming.

DCS INTRODUCTION
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
1-2
1.2 Programming Overview
When the keyphone system arrives from the factory it contains default data. This needs
to be customised, using the MMC programs, to suit the customer’s requirements.
MMC stands for Man Machine Code and each MMC is assigned a three-digit code (100,
101, and so on). These MMCs are used to view, create or change customer data on a
display keyphone (called KMMC programming). For example, MMC 601 is used to cre-
ate a station group; system speed dial numbers are entered in MMC 705; key functions
are assigned to individual keyphones (or “keysets”) using MMC 722; and system dial-
ling codes (such as extension numbers and feature codes) can be changed in MMC
724.
1.3 Programming Levels
There are three levels of programming: System level, Customer level and Station level.
System and Customer levels allow system-wide programming and are under passcode
protection to restrict access. System programming is done by the system installer (or
system technician), usually on a one-off basis, but also to manage any changes in the
customer’s requirements. Customer programming is done by the system administrator,
on a day to day basis, to manage station users’ requirements. Station level program-
ming does not require a passcode, allowing station users to make simple changes to
their keyset features.
To prevent conflicting data from being entered, only one person at a time can enter Sys-
tem or Customer programming. If you attempt to enter programming mode while an-
other keyset is being used for programming, your display shows [xxx PGM MODE]
where “xxx” is the keyset extension number of the station in programming mode. While
programming is in progress, normal system operation is not affected.
1.3.1 System Level
This level is entered via MMC 800 and requires the installer’s (technician’s) passcode.
This is the highest level and allows access to all system programs, station programs
and maintenance programs. The installer (sometimes called the installing technician)
also decides which programs are accessible to the customer (the system administrator)
at Customer level.
•All MMCs are accessible at this level.
1.3.2 Customer Level
This level is entered via MMC 200 and requires the customer’s passcode. It allows ac-
cess to station programs and system programs permitted by the system installer in
MMC 802. When the system administrator uses the customer passcode to access sta-
tion programs, data for all stations can be viewed or changed. Changes can be made
either system-wide or to selected keysets. (The system administrator should also refer
to the System Administrationmanual for their keyphone system if this is available.)
•Accessible MMCs at this level are designated by the installer.

DCS INTRODUCTION
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
1-3
1.3.3 Station Level
The system administrator or keyset user can access certain programs at a station with-
out using a passcode. At this level, only data for the selected station can be changed.
You should refer to the instructions provided in theSamsung DCS Keyset User Guide.
•Accessible MMCs at this level are nos. 100–121.
1.4 Keys Used for Programming
Programming may be done from any 6-button (6B), 12-button (12B) or 24-button (24B)
keyset with a liquid crystal display (LCD). (Refer to the Samsung DCS Keyset User Guide
for a full description of keyset operation.)
1.4.1 Soft Keys
The three keys directly below
the LCD are called soft keys.
The left-hand soft key is desig-
nated as the LEFT soft key. This
key is used to save any
changed data while program-
ming, or to move the cursor to
the left on the LCD.
The right-hand soft key is des-
ignated as the RIGHT soft key.
This key is used to save any
changed data while program-
ming, or to move the cursor to
the right on the LCD.
DCS Euro Display Keysets
1.4.2 Other Keys
The following keys perform special functions:
VOLUME UP (+) / DOWN (–)Scroll up/down through available options*
KEYPAD Enter data using keys 0–9 and [, and dial options*
HOLD Clear previous entry
ANS/RLS Select “ALL” option (e.g. to make data apply to all,
rather than selected, stations)
SPEAKER Store data and advance to next MMC
TRSF Enter programming mode or
Store data and exit programming mode
* Note: Many MMCs allow you to dial codes using the keypad to select options quickly. Alterna-
tively, you can press the VOLUME Up and Down keys (+ and –) to scroll through and select op-
tions. Use whichever method you prefer.

DCS INTRODUCTION
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
1-4
The 6, 12 or 24 extra programmable keys can be set up to perform specific functions
when pressed during normal operation. During programming, some of these keys also
perform other specific functions. This is described in the individual MMC program pro-
cedure where applicable.
1.5 Programming Procedures
1.5.1 Precautions When Programming
•The keyset must be on-hook (handset down) to allow programming.
•Programming is available on any digital keyset with an LCD.
•Programming is available only on digital telephones (not analogue ones).
•If ‘INVALID DATA’ appears in the LCD while programming, you should re-enter the
correct data.
•When you have successfully completed an entry, the LCD automatically changes for
the next step.
•Programming halts if you have not pressed a key for a certain period of time (30 sec-
onds by default, but this can be changed).
•Programming halts if you pick up the handset while programming.
•If you pick up the handset while programming, or the telephone plug is pulled out,
any new data shown in the LCD are saved.
IMPORTANT
When installing and programming a ‘default’ system
for the first time:
The system requires that you select the correct software version for your coun
try
(e.g. by selecting “UK”) before you can do any other programming via either a ke
y-
phone (KMMC programming) or a PC (PCMMC programming).
To select the country:
1. Press the TRSF key.
2. Enter 800 followed by the default passcode (4321)
The system sounds a warning and displays on the keyset:
Use the VOLUME Up/Down keys to
select the country and press the RIGHT soft key.
The keyset displays:
Use the VOLUME Up/Down keys to select YES and press the RIGHT soft key. When
defaulted to the correct version, you can open programming as de
scribed next. The
country version selected can be changed in MMC 812, Select Country.
ENABLE TECH. PROG
SELECT COUNTRY
DEFAULTINGSYSTM
ARE YOU SURE?NO

DCS INTRODUCTION
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
1-5
1.5.2 Opening System or Customer Programming
Toopenprogramming:
1. Press the TRSF key.
2. Enter the MMC program number 200 (for Customer level programming) or 800 (for
System level programming).
3. Enter the relevant passcode.
4. Press key 1 (or use the VOLUME Up or Down key) to select ‘ENABLE’.
5. Press the SPEAKER key to have the program selection mode appear (or press the
TRSF key to halt programming).
6. Enter the MMC number, or select the program number with the Up or Down key and
press the SPEAKER key.
When opening system programming, you are advised to check MMC 812 (Select Coun-
try) to ensure that the correct country has been selected before you do any other pro-
gramming.
Carefully follow the instructions given with each MMC to program your system correctly.
1.5.3 Opening Station Level Programming
Toopenprogramming:
1. Press the TRSF key.
2. Enter the MMC program number.
Carefully follow the instructions given with each MMC to program your system correctly.
1.5.4 Programming DCS-408 and 408i Systems
Although physically similar in appearance, the “408” and “408i” are different systems and
may have different programming requirements and features. For example, the 408i sup-
ports ISDN whereas the 408 does not. Thus, an MMC relevant to one system may not be
relevant to the other. Similarly, where an MMC relates to both systems, some features
available on the 408i system may not be available on the 408 system, and vice versa.
This will be indicated in the MMC description, where appropriate.
These systems also differ significantly from all other keyphone systems, both in size and
physical appearance. In comparison with other systems, when programming your 408 or
408i:
•Extension, group and trunk numbers are two digits by default (e.g. extension 21,
trunk 71, etc). All other systems use 3-digit numbers by default (e.g. extension 201,
trunk 701, etc).* Examples of programming shown in this manual use 3-digit num-
bers for convenience only.
(*Unless changed by the system installer in MMC 724.)
•You can set up to four ‘Normal’ station groups. Group types AA, VM/AA and UCD
are not permitted.
•Only two trunk groups, 8 and 9, are available. (All other systems support groups 9
and 80–82.)

DCS MMC LIST
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-1
Part 2. Program MMC List & Default Data
2.1 Program (MMC) List
100: STATION LOCK 317: ASSIGN STATION/STATION USE
101: CHANGEUSERPASSCODE 318: DISTINCTIVE RING
102: CALL FORWARD 319: BRANCH GROUP
103: SET ANSWER MODE 400: CUSTOMER ON/OFF PER TRUNK
104: STATION NAME 401: CO/PBX LINE
105: STATION SPEED DIAL 402: TRUNK DIAL TYPE
106: STATION SPEED DIAL NAME 403: TRUNK TOLL CLASS
107: KEY EXTENDER 404: TRUNK NAME
108: STATION STATUS 405: TRUNK NUMBER
109: DATE DISPLAY 406: TRUNK RING ASSIGNMENT
110: STATION ON/OFF 407: FORCED TRUNK RELEASE
111: KEYSET RING TONE 408: ASSIGNTRUNKMUSICONHOLDSOURCE
112: ALARM REMINDER 409: TRUNK STATUS READ
113: VIEW MEMO NUMBER 410: ASSIGN DISA TRUNK
114: STATION VOLUME 411: ASSIGN E1 SIGNAL TYPE
115: SET PROGRAMMED MESSAGE 412: ASSIGN TRUNK SIGNAL
116: ALARM AND MESSAGE 414:MPD/PRS SIGNAL
119: SET CLIP DISPLAY 415:REPORT TRUNK ABANDON DATA
121:KEYSET LANGUAGE 416: ASSIGN AC15 TRANSLATION
200: OPEN CUSTOMER PROGRAMMING 417: PRI CRC4 OPTION
201: CHANGE CUSTOMER PASSCODE 418: CARD RESTART
202: CHANGE FEATURE PASSCODES 419: BRI OPTION
203: ASSIGN UA DEVICE 420: PRI OPTION
204: COMMON BELL CONTROL 421: MSN DIGIT
205: ASSIGN LOUD BELL 422:ASSIGN TRUNK COS
206: BARGE-IN TYPE 423:S/T MODE
207: ASSIGNVM/AAPORT 424: S0MAPPING
208: ASSIGN RING TYPE 426:TRUNK GAINCONTROL
209: ASSIGN ADD-ON MODULE 427: R2MFC SIGNAL
210: CUSTOMER ON/OFF 428: ASSIGN TRUNK/TRUNK USE
211: DOOR RING ASSIGNMENT 500: SYSTEM-WIDE COUNTERS
212: ALARM RINGING STATION501: SYSTEM-WIDE TIMERS
213: ALARM MESSAGE 502: STATION-WIDE TIMERS
214: DISA ALARM RINGING STATION 503: TRUNK-WIDE TIMERS
215: VOICE DIALLER OPTIONS504: PULSE MAKE/BREAK RATIO
216: VOICE DIALLER ASSIGNMENTS 505: ASSIGN DATE AND TIME
217: CCC OPTION 506: TONE CADENCE
219:COMMON RELAY SERVICE TYPE 507: ASSIGN AUTO NIGHT TIME
220: ISDN SERVICE TYPE 508: CALL COST
300: CUSTOMER ON/OFF PER STATION 509: C.O. TONE CADENCE
301: ASSIGN STATION COS 510: SLI RING CADENCE
302: PICKUP GROUPS 511: MW LAMP CAD
303: ASSIGN BOSS/SECRETARY512: ASSIGN HOLIDAY
304: ASSIGN STATION/TRUNK USE 600: ASSIGN OPERATOR GROUP
305:ASSIGN FORCED CODE 601: ASSIGN STATION GROUP
306:HOT LINE 602: STATION GROUP NAME
308: ASSIGN BACKGROUND MUSIC SOURCE 603: ASSIGN TRUNK GROUP
309: ASSIGN STATION MUSIC ON HOLD 604: ASSIGN STATION TO PAGE ZONE
310: LCR CLASS OF SERVICE 605: ASSIGN EXTERNAL PAGE ZONE
311: ASSIGN SIM PARAMETER 606: ASSIGN SPEED BLOCK
312: ALLOW CLIP 607: UCD OPTIONS
313: ASSIGN PIN CODE 608: ASSIGN CLIP REVIEW BLOCK
314: CONFIRM OUTGOING CALL700: COPY COS CONTENTS
315:SET RELOCATION 701: ASSIGN COS CONTENTS
316:COPY STATION USABLE 702: TOLL DENY TABLE

DCS MMC LIST
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-2
703: TOLL ALLOWANCE TABLE 736:ASSIGN AA MOH
704: ASSIGN WILD CHARACTER737: DECT SYSTEM CODE
705: ASSIGN SYSTEM SPEED DIAL 738: DECT CLEAR REGISTRATION
706: SYSTEM SPEED DIAL BY NAME 739: BSI DOWNLOAD
707: AUTHORISATION CODE 740: STATION PAIR
708: ACCOUNT CODE 741: BSI CARD RESTART
709: PBX ACCESS CODE 742:BSI STATUS
710: LCR DIGIT TABLE 743:DECT BASE STATION (DBS) STATUS
711: LCR TIME TABLE 744:DECT REGISTRATION ON/OFF
712: LCR ROUTE TABLE 745: BSI CARRIER
713: LCR MODIFY DIGIT TABLE 750: VM CARD RESTART
714: DDI NUMBER & NAME TRANSLATION 751: ASSIGN MAILBOX
715: PROGRAMMED STATION MESSAGE 752: AUTO RECORD
716: UK LCR OPTION 753: WARNING DESTINATION
717: PIN CODE 754: VM HALT
718: MY AREA CODE 755: VM ALARM
720: COPY KEY PROGRAMMING 756: ASSIGN VM MOH
721: SAVE STATION KEY PROGRAMMING 757: VM IN/OUT
722: STATION KEY PROGRAMMING 800: ENABLE TECHNICIAN PROGRAM
723: SYSTEM KEY PROGRAMMING 801: CHANGE TECHNICIAN PASSCODE
724: DIAL NUMBERING PLAN 802: CUSTOMER ACCESS MMCNUMBER
725: SMDR OPTIONS 803: ASSIGN TENANT GROUP
726: VM/AA OPTIONS 804: SYSTEM I/O PARAMETER
727: SYSTEM VERSION DISPLAY 805: TX LEVEL & GAIN
728: CLIP TRANSLATION TABLE 806: CARD PRE-INSTALL
730:AA RECORD GAIN 807: VOLUME CONTROL
731:AA RAM CLEAR 808: T1 TRUNK CODING
732: AA TRANSLATION TABLE 809: SYSTEM MMC LANGUAGE
733: AA PLAN TABLE 810: HALT PROCESSING
734: AA MESSAGE MATCH 811: RESET SYSTEM
735:AA USE TABLE 812: SELECT COUNTRY

DCS DEFAULT DATA
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-3
2.2 Default Data
Station Programs
DCS CI CII 816 408 408i
100: STATION LOCK YYYYYYALL STATIONS UNLOCKED
101: CHANGE USER PASSCODE YYYYYYALL STATION PASCODES=1234
102: CALL FORWARD YYYYYYALL STATION=0 (FWD CANCEL)
103: SET ANSWER MODE YYYYYYALL KEYSETS ‘RING’
RING FREQUENCY DEFAULT=5
104: STATION NAME YYYYYYNONE
105: STATION SPEED DIAL YYYYYYNONE
106: STATION SPEED DIAL NAME YYYYYYNONE
107: KEY EXTENDER YYYYYYNONE
108:STATION STATUS YYYYYYSEE MMC 108
109: DATE DISPLAY YYYYYYCOUNTRY:WESTERN
CLOCK: 24-HOUR
DISPLAY: LOWERCASE
110: STATION ON/OFF YYYYYYAUTOHOLD:OFF
AUTO TIMER: ON
HEADSETMODE:OFF
HOT KEYPAD: ON
KEY TONE: ON
PAGE REJOIN: ON
RING PREFERENCE: ON
CALL COST: OFF
AME BGM: OFF
AME PSWD: OFF
111: KEYSET RING TONE YYYYYYSELECTION=5
112: ALARM REMINDER YYYYYYALARMS SET TO NOTSET
113: VIEW MEMO NUMBER YYYYYYNO MEMOS ENTERED
114: STATION VOLUME YYYYYYRING VOL: 4
OFF HOOK RING VOL: 4
HANDSET VOL: 4
SPEAKER VOL: 13
BGM VOL: 13
115: SETPROGRAMMEDMESSAGE YYYYYYNO MESSAGES SELECTED
116: ALARM AND MESSAGE YYYYYYALARMS SET TO NOTSET
119: SET DISPLAY YYYYNYNAME FIRST
121: KEYSET LANGUAGE YNYYYYENGLISH

DCS DEFAULT DATA
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-4
System Programs
DCS CI CII 816 408 408i
200: OPEN CUSTOMER PROGRAMMING YYYYYYCLOSED(DISABLED)
201: CHANGE CUSTOMER PASSCODE YYYYYYPASSCODE =1234
202: CHANGE FEATURE PASSCODES YNYYYYDAY/NIGHT=0000
DISA ALARM=5678
ALARM CLR=8765
AA RECORD=4321
DECT (BSI) REGISTER =4321
203: ASSIGN UA DEVICE YYYYYYNONE
204: COMMON BELL CONTROL YYYYYYCONTINUOUS
205: ASSIGN LOUD BELL YNYYYYUNASSIGNED
206: BARGE-IN TYPE YYYYYYNO BARGE IN
207: ASSIGN VM/AA PORT YYYYYYNORMAL PORT
208: ASSIGN RING TYPE YYYYYYICM RING
209: ASSIGN ADD-ON MODULE YYYYNNNONE FOR MASTER
210: CUSTOMERON/OFF YYYYYYSEE MMC 210
211: DOOR RING ASSIGNMENT YYYYYYSTATION GROUP 500 (or 50)
212: ALARM RINGING STATION YNYNNNALL SENSORS RING 500
DAY/NIGHT
213: ALARM MESSAGE YNYNNNNONE
214: DISA ALARM RINGING STATION YYYYYYDAY/NIGHT=500 (or 50)
215: VOICEDIALLEROPTIONSYYYNNN2CH-7USER-20BIN
216: VOICE DIALLER ASSIGNMENTS YYYNNNNONE
217: CCC OPTION NYNNNNNONE
219: COMMON RELAY SERVICE TYPE NNYYYYSEE MMC 219
220: ISDN SERVICE TYPE YYYYNYVOICE
300: CUSTOMER ON/OFF PER STATION YYYYYYSTN CALL PRT : OFF
FWD DLY USE : OFF
OTHER FEATURES SET TO
ON
301: ASSIGN STATION COS YYYYYYDAY CLASS = 1
NIGHT CLASS = 1
302: PICKUP GROUPS YYYYYYALL STATIONS GROUP 1
303: ASSIGN BOSS/SECRETARYYYYYYYNONE
304: ASSIGN STATION/TRUNK USE YYYYYYDIAL = YES
ANS = YES
305: ASSIGN FORCED CODE YYYYYYNONE
306: HOT LINE YYYYYYNONE
308: ASSIGN BACKGROUND MUSIC
SOURCE YYYYYYNONE
309: ASSIGN STATION MUSIC ON HOLD YYYYYYNONE
310: LCR CLASS OF SERVICE YYYYYYLEAST COST ROUTING
COS 1

DCS DEFAULT DATA
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-5
DCS CI CII 816 408 408i
311: ASSIGN SIM PARAMETER YNNNNNSIM TYPE = DTE
CALL MODE = MANUAL
ANS MODE = MANUAL
AUTO BAUD = ON
DTR CHECK = ON
ECHO = ON
PROTOCOL = V110
SPEED = 9600
CHAR LENGTH = 8 BITS
PARITY = NONE
STOP BIT = 1
312: ALLOW CLIP YYYYNYRCV=YES, SEND=YES,
INFO=CO Tel
313: ASSIGN PIN CODE NYNNNNALL STATIONS ARE CODE
#1
314: CONFIRM OUTGOING CALLYNYYYYNONE
315: SET RELOCATION YNYYYYNONE
316: COPY STATION USABLE YNYYNNNONE
317: ASSIGN STATION/STATION USE YNYYNNDIAL=YES
318: DISTINCTIVE RING YNYYYYT=F-STN, C=F-STN
319: BRANCH GROUP ––––––NOT USED IN UK
400: CUSTOMER ON/OFF PER TRUNK YYYYYY1A2 EMULATE: OFF
TRUNK INC DND: OFF
TRUNK FORWARD: ON
LCR ALLOW:OFF
401: C.O./PBX LINE YYYYYYALL TRUNKS C.O. LINE
402: TRUNK DIAL TYPE YYYYYNALL TRUNKS DTMF
403: TRUNK TOLL CLASS YYYYYYALL TRUNKS F-STN
DAY/NIGHT
404: TRUNK NAME YYYYYYNO NAMES ENTERED
405: TRUNK NUMBER YYYYYYNO NUMBERS ENTERED
406: TRUNK RING ASSIGNMENTYYYYYYALL TRUNKS DAY/NIGHT:
500 (or 50)
407: FORCED TRUNK RELEASE YYYYYYNONE
408: ASSIGN TRUNK MUSIC ONHOLD
SOURCE YYYYYYTONE
409: TRUNK STATUS READ YYYYYYSEE MMC 409
410: ASSIGN DISA TRUNK YYYYYYALL TRUNKS NORMAL
411: ASSIGN E1 SIGNAL TYPE––––––NOT USED IN UK
412: ASSIGN TRUNK SIGNAL YYYNNNIMMEDIATE
414: MPD/PRS SIGNAL YYYYYNNONE
415: REPORT TRUNK ABANDONDATA YYYYNYREPORT=YES
416: ASSIGN AC15 TRANSLATION YYYNNNUNUSE DID TRANS
417: PRI CRC4 OPTION YNYNNNCRC4ON
418: CARD RESTART YYYYNYNONE

DCS DEFAULT DATA
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-6
DCS CI CII 816 408 408i
419: BRI OPTION YYYYNYCHANNEL ANY: YES
BRI MODE: P-P DDI
DLSEND: OVERLAP
BRI CODING: A-LAW
POWERFEED: NO
420: PRI OPTION YNYNNNCHANNEL ANY: YES
PRI MODE: DDI
DLSEND: OVERLAP
421: MSN DIGIT YYYYNYNONE
422: ASSIGN TRUNK COS YYYYYYDAY CLASS: 1
NIGHT CLASS: 1
423: S/T MODE YYYYNYTRUNK
424: S0MAPPING YYYYNYNONE
426: TRUNK GAIN CONTROL YNYYYYRX=+0.0 dB, TX=+0.0 dB
(ALL TRUNKS)
427: R2MFC SIGNAL NNNNNNNOT USED IN UK
428: ASSIGN TRUNK/TRUNK USE YNYYNNDIAL=YES
500: SYSTEM-WIDE COUNTERS YYYYYYSEE MMC 500
501: SYSTEM-WIDE TIMERS YYYYYYSEE TABLE OF TIMERS
AND VALUES IN MMC 501
502: STATION-WIDE TIMERS YYYYYYNO ANS FWD: 015 SEC
DTMF DURATION: 100 MS
FIRST DGT DELAY: 600MS
503: TRUNK-WIDE TIMERS YYYYYYANS.BAK TM: 600 MS
CLEARING: 002 SEC
CO SUPV TM: 400 MS
DTMF DURATION: 100 MS
FIRST DGT DELAY: 600MS
FLASH TIME: 070 MS
NO RING TM: 004 SEC
PAUSE TIME: 003 SEC
PRS DET TM: 000 MS
RNG DET.TM: 300 MS
WINK: 200 MS
MF/DP INT TM: 0800 MS
MFR DLY TM: 000 SEC
504: PULSE MAKE/BREAK RATIO YYYYYNMAKE/BREAK = 33
PULSES PER SECOND = 10
505: ASSIGN DATE AND TIME YYYYYYFOLLOWS S/W VERSION
RELEASEDATE
506: TONECADENCE YYYYYYSEE MMC 506
507: ASSIGN AUTO NIGHT TIME YYYYYYNONE
508: CALL COST YYYYYYUNIT COST PER MP: 200
PENCE
CALL COST RATE: 100%
509: C.O. TONE CADENCE NYNNNNSEE MMC 509
510: SLI RING CADENCE YYYYYYSEE MMC 510
511: MW LAMP CAD YNYNNNON: 1000MS, OFF: 1000MS
512: ASSIGN HOLIDAY YNYYYYNONE
600: ASSIGN OPERATOR GROUPYYYYYYDAY/NIGHT: 500 (or 50)

DCS DEFAULT DATA
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-7
DCS CI CII 816 408 408i
601: ASSIGN STATION GROUP YYYYYYSEE MMC 601
602: STATION GROUP NAME YYYYYYNONE
603: ASSIGN TRUNK GROUP YYYYYYSEE MMC 603
604: ASSIGN STATION TO PAGE ZONE YYYYYYNO STATIONS ASSIGNED
’ALL ZONE’ IS SET
605: ASSIGN EXTERNAL PAGEZONE YYYYYYNONE
606: ASSIGN SPEED BLOCK YYYYYYSYSTEM: SEE MMC 606
STATIONS: ONE BIN OF 10
ENTRIES
607: UCDOPTIONS YYYYNNSEE MMC 607
608: ASSIGN CLIP REVIEW BLOCK YYYYNYONE BIN OF 10 ENTRIES
700: COPY COS CONTENTS YYYYYYNONE
701: ASSIGN COS CONTENTS YYYYYYTOLL LEVEL: ALL COS=A
ALL FEATURES (EXCL.
OVERRIDE)=YES
702: TOLL DENY TABLE YYYYYYALL ENTRIES=0
703: TOLL ALLOWANCE TABLE YYYYYYALL ENTRIES=0
704: ASSIGN WILD CHARACTERYYYYYYALL X, Y, Z=1
705: ASSIGN SYSTEM SPEEDDIAL YYYYYYNONE
706: SYSTEM SPEED DIAL BY NAME YYYYYYNO NAMES
707: AUTHORISATIONCODE YYYYYYNONE
708: ACCOUNTCODE YYYYYYNONE
709: PBX ACCESS CODE YYYYYYNONE
710: LCR DIGIT TABLE YYYYYYDEPENDS ON S/W VER-
SION
711: LCR TIME TABLE YYYYYYSEE MMC 711
712: LCR ROUTE TABLE YYYYYYSEE MMC 712
713: LCR MODIFY DIGIT TABLE YYYYYYDEPENDS ON S/W VER-
SION
714: DDI NUMBER AND NAME TRANSLA-
TION YYYYNYSEE MMC 714
715: PROGRAMMED STATION
MESSAGE YYYYYY20 MESSAGES (10 PRE- PROGRAMMED) (SEE MMC
715)
716: UK LCR OPTIONS YYYYYYSEE MMC 716
717: PIN CODE NYNNNNNONE
718: MY AREA CODE ––––––NOT USED IN UK
720: COPY KEY PROGRAMMING YYYYYYNONE
721: SAVE STATION KEY PROGRAMMING YYYYYYRESTORE
722: STATION KEY PROGRAMMING YYYYYYSEE MMC 722
723: SYSTEM KEY PROGRAMMING YYYYYYSEE MMC 723
724: DIAL NUMBERING PLAN YYYYYYSEE MMC 724
725: SMDR OPTIONS YYYYYYSEE MMC 725
726: VM/AAOPTIONS YYYYYYSEE MMC 726

DCS DEFAULT DATA
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
2-8
DCS CI CII 816 408 408i
727: SYSTEMVERSIONDISPLAY YYYYYYINSTALLEDCARDVERSIONS
728: CLIP TRANSLATION TABLE YYYYNYNONE
730: AA RECORD GAIN YNYYNN+0.0 dB
731: AA RAM CLEAR YYYYNNNONE
732: AA TRANSLATION TABLE YYYYNNSEE MMC 732
733: AA PLAN TABLE YYYYNNSEE MMC 733
734: AA MESSAGE MATCH YYYYNNMSG INDEX NO.
735: AA USE TABLE YYYYNNPLAN 01
736: ASSIGN AA MOH YYYYNNNOT USE
737: DECT SYSTEM CODE YYYNNNAUTH CODE: FFFF
SYSTEM ID: 000
738: DECT CLEAR REGISTRATION YYYNNNFORCED MODE
739: BSI DOWNLOAD YYYNNNNONE
740: STATION PAIR YYYYNNNONE
741: BSI CARD RESTART YYYNNNNONE
742: BSI STATUS YYYNNNNONE
743: DBS STATUS YYYNNNNONE
744: DECT REGISTRATION ON/OFF YYYNNNDISABLE
745: BSI CARRIER YYYNNN1111111111
750: VM CARD RESTART YNYNNNDOWNLOAD=YES
751: ASSIGN MAILBOX YNYNNNALL STN=YES, ALL GRP=NO
752: AUTO RECORD YNYNNNMB=NONE, PORT=NONE
CALL=I
753: WARNINGDESTINATION YNYNNNDEST=500
754: VM HALT YNYNNNNONE
755: VM ALARM YNYNNNTHRESHOLD=80%
756: ASSIGN VM MOH YNYNNNNOT USE
757: VM IN/OUT YNYNNNIN/OUT
800: ENABLE TECHNICIAN PROGRAM YYYYYYDISABLE
801: CHANGE TECHNICIAN PASSCODE YYYYYYDEFAULT PASSCODE = 4321
802:CUSTOMER ACCESS MMC NO. YYYYYYSEE MMC 802
803: ASSIGN TENANT GROUP YNNNNNALLASSIGNMENTSTENANT 1
804: SYSTEM I/O PARAMETER YYYYYYSEE MMC 804
805: TX LEVEL AND GAIN YYYYYYSEE MMC 805
806: CARD PRE-INSTALL YYYYNNNONE
807: VOLUMECONTROL YYYYYYSEE MMC 807
808: T1 TRUNK CODING ––––––NOT USED IN UK
809: SYSTEM MMC LANGUAGE YNYYYYENGLISH
810: HALT PROCESSING YYYYNNNONE
811: RESET SYSTEM YYYYYYNONE
812: SELECT COUNTRY YNYYYYNONE

2.3 System Configuration: Quick Reference
Description DCS Compact I Compact II 816 408 408i
AA card port numbers 3951–83951–6381–61381–4N/A N/A
AA Translation tables 1 & 2 (entries) 100 100 100 50 N/A N/A
Account codes 500 250 200 200 100 100
Authorisation codes 250 100 100 30 10 10
BGM port numbers 3701–2371–2371–2371–2371 371
CALL keys (max.) 885422
Classes of Service (COS) 30 30 30 10 44
CLIP Translation Table entries 250 250 200 200 N/A 100
Daughterboards (keyset) KSU Any DLI port Motherboard None None None
DDI entries 200 200 200 50 N/A 20
DECT ports 48 24 24 N/A N/A N/A
LCR Digit Table (max. entries) 500 500 500 300 100 100
MOH port numbers 3701–2371–2371–2371–2371 371
Operator Groups (partofStation Group)111111
Operator Group members (sequential / dis-
tributed ring) 32 30 30 16 88
Operator Group members (unconditional
ring) 32 30 10 16 88
Page zones (no. of internal) 444422
Page zones (no. of external) 444111
Pickup Groups 20 20 20 844
2-9
S0 bus ports 32 32 24 16 None 2

2.3 System Configuration: Quick Reference (cont’d)
Description DCS Compact I Compact II 816 408 408i
Speed dials (total) 1500 500 600 500 300 300
Speed dials (system)(max.) 500 500 500 300 200 200
Station Groups (number of) 30 30 20 10 44
Station Group members (sequential / dis-
tributed ring) 48 30 30 16 88
Station Group members (unconditional
ring) 32 30 10 16 88
Station Group numbers 500–529 500–529 500–519 500–509 50–53 50–53
Trunk Groups (number of) 11 11 11 422
Trunk Group members 80 10 40 10 44
Trunk Group numbers 9, 80–89 9, 80–89 9, 80–89 9, 80–82 9, 8 9, 8
UCD Groups 1021025334N/A N/A
2-10
Voice dial card port numbers 3551–23551–2355–6N/A N/A N/A
Notes:
1Misc 2 card=381–4, AA card=381–6, both cards installed=381–90
2UCD Group can be created from any Station Group 501–529 (CI) or last 10 Station Groups 520–529 (DCS)
3UCD Group can only be created from last 10 Station Groups 510–519
4UCD Group can only be created from last three Station Groups 507–509

DCS SPECIAL APPLICATIONS
COMBINED PROGRAMMING MANUAL NOVEMBER 2001
3-1
Part 3. Special Applications
Part 3 provides additional information covering the following topics:
•Voice Mail / Auto Attendant Integration
•Individual Station Page
•CLIP (Calling Line Identification Presentation)
•Toll Restriction (Call Barring) Overview
•S0Overview