Sanuvox BIOPUR User manual

Advanced Indoor Air Quality Systems
Operating Instructions
Specifications
·Plug Type: AC120V (Two Flat)
·Cord Length: 2.6m.
Power Supply：AC120V/60Hz.
Three Speeds:
III=1250±100RPM
II=1000±100RPM
I=650±100RPM
·Rated Power: 50W
3
·CADR= 150 m /h
3
·Air Flow= 165 m /h (140 CFM)
·Product Size：336 X 235 X595 mm
·Unit Weight：6.7Kg.
UV BIOPÜR Air Treatment System
1-888-726-8869 www.sanuvox.com 7.

Operating Instructions
HEPA Change
or Clean
Reset
Speed
Setting
Timer
Setting
ON / OFF
Button
UV/ ION
Button
ION
Auto
Air-Flow
API Display
Timer
UV
8.
a.
b.
c.
d.
BEFORE FIRST USE please follow the instructions below:
Upon removing the unit from the box:
1. Remove the unit from the plastic bag
2. Remove the cover
3. Remove the Styrofoam
4. Twist latch to allow the filters to be removed
5. Remove all 4 filters
6. Remove filters from the plastic bag
7. Replace filters in the following order
a. TiO2
b. Carbon
c. HEPA
d. Pre-filter
8. Once filters are placed back inside the unit
turn the latch to keep the filters in place
9. Securely replace the cover
10. Unit is ready for use

Operating Instructions
1. Press to start the unit.
2. The default setting for the unit is Speed II. To change speed settings press . Each time the button is pressed,
the unit will cycle through the different FAN speeds (I→II→III→Auto).
3. The unit is equipped with a TIMER feature. To set a desired interval of time press
1Hr→2Hr→4Hr→6Hr→8Hr → cancel timer. As the user cycles through the different time intervals, the different times
will be shown (i.e. )
4. The default setting is to have both UV/ION 'ON'. The UV/ION button toggles this feature ON and OFF. The
LCD will display when both UV and ION are on.
5. For AUTO mode (Press until the LCD display shows “AUTO”). In this mode the API (Air Pollution Index) will
control the unit's speed. The “API” measures the air quality and adjusts system performance automatically. The API
Scale is a visual representation of the air quality and will change depending on the air quality.
6. Maintenance (HEPA, Carbon filter and UV Lamp). When the HEPA filter icon blinks (after approximately 2
years / 17,500 hours of operation) it is time to replace the HEPA, Carbon filter and UV Lamp. Contact your local vendor
for the replacement kit or contact Sanuvox at 1-888-726-8869. Follow the instructions that will accompany the
replacement kit on how to replace the UV Lamp. Once the contents of the replacement kit have been installed use a
paperclip (or similar object) to press and hold the reset button for 3 seconds. This will reset the HEPA notification icon
on the LCD. The included HEPA filter can be cleaned when so desired to maintain system performance.
7. To remove the front cover (see Figure A. on page 10), grasp the bottom of the unit and pull up and away from the unit.
Once detached from the unit, lift the cover upwards.
8. To remove the HEPA filter for cleaning or replacement, turn the lock as to allow for the pre-filter and HEPA to be easily
removed from the unit. Pull on
the tab located at the top of the
filter to remove.
“High Particle Count"
“Low Particle Count”
9.

Operating Instructions
9. To Clean the HEPA and pre-filter, remove the black foam pre-filter from the
HEPA filter (these are attached with Velcro). Shake off or wash the pre-filter
to clean any dirt and/or particulates from the media. Use a vacuum cleaner to
clean off the HEPA Filter.
10. Filter Sequence (from the bottom up)
Tio catalyst→Carbon filter→HEPA filter→Pre-filter
2
11. To replace the unit's front cover (see Figure B. below), first fit the top of the unit into place and slowly press the bottom
as to allow the bottom clips to catch.
12. Remote control. The unit comes with an included infrared remote control. To use the remote control, point the remote
in the direction of the LCD display.
1
2
After replacing the HEPA filter,
Lock the filters into place by turning the lock.
2
1
To remove cover To replace cover
10.
Figure A. Figure B.
Carbon filter
Tio2 catalyst
HEPA filter
Pre-filter

Sanuvox Warranty
Sanuvox warrants the UV system to be free from defects in material and workmanship subject to the conditions and limitations
hereinafter described. The warranty period is 1 year from the date of purchase.
Warranty claims are to be made to Sanuvox directly. The customer shall contact Sanuvox at 1-888-726-8869 to obtain the
address of a Sanuvox Service Center where the defective unit is to be shipped (at customer's expense) along with a copy of the
original invoice. Sanuvox will repair and return the unit to the customer at Sanuvox's expense.
SANUVOX WILL NOT BE RESPONSIBLE FOR
ŸNormal maintenance as outlined in the installation and servicing instructions or owner's manual.
ŸDamage or repairs required as a consequence of faulty installation or application by others.
ŸFailure to start due to voltage conditions, blown fuses, open circuit breakers or other damages due to the inadequacy or
interruption of electrical service.
ŸDamage or repairs needed as a consequence of any misapplication, abuse, improper servicing, unauthorized alteration, or
improper operations.
ŸDamage as a result of floods, winds, fires, lightning, accidents, corrosive atmosphere, or other conditions beyond the
control of Sanuvox.
ŸParts not supplied or designated by Sanuvox Technologies Inc.
ŸSanuvox Technologies Inc products installed outside the Continental U.S.A., Alaska, Hawaii, and Canada.
ŸANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER.
ŸSome states or provinces do not allow the exclusion of incidental or consequential damages, so the above limitation may
not apply to you.
Operating Instructions
1-888-726-8869 www.sanuvox.com 11.
Product Registration
Please register your purifier on-line at www.sanuvox.com. The registration link is at the bottom of the page.
Benefits of on-line registration are:
Sanuvox can contact you with important product notifications
Sanuvox can confirm ownership
Sanuvox can continue to develop and design products that meet your needs