Sargent and Greenleaf 6128-240 A Series Installation guide

1
Sargent and Greenleaf
General Information
The Sargent & Greenleaf Models 6128, 6129 and 6106-240 are
designed to provide a high level of security combined with
exiblefeaturesthatallowmultiplelevelsofcontrolovernormal
operations and service access. Follow these instructions
carefully to get the best possible use from your lock.
Introduction
• A-Series electronic safe locks incorporate sophisticated
electronic circuitry. These locks are suitable for indoor use only.
• The keypad should only be cleaned with a soft, dry cloth.
Avoid the use of solvents or liquids.
• Never attempt to lubricate the lock or keypad components.
Serviceshouldonlybeperformedbyaqualiedtechnician.
• Anytime the keypad is removed from its mounting base, either
disconnect the lock cable or support the keypad so that it does
not hang by the cable. This could adversely affect the cable
connector or the keypad receptacle.
• Each time a button is pressed, and the lock accepts the input, it emits a “beep,” and the LED on the keypad lights momentarily.
• All the letters of the English alphabet are displayed on the keypad. This allows you to devise numeric, alphanumeric, or word-based
codes. Use whatever approach works best for you.
•Allcodesendwith#.Thissignalsthelockthatyouhavenishedenteringalldigitsofthecode.
• Personal data which can be directly related to a code holder, such as a birthdate, should not be used in making up a lock code.
Avoid codes which can be easily guessed.
• After the lock is changed to a new code, the lock function must be checked by locking and unlocking it several times with the
container door open. Make sure it functions correctly before closing the door.
Programming and Operations Guide
Model 6128/6129 and 6106-240 A-Series
Revision 02/15/2022 Document: 630-600
Note: This lock has been Listed by Underwriters Laboratories for use with the following S&G keypad(s):
6120-0XX, 61KP-1XX, 61KP-2XX

2
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
Table of Contents
Programming and Operations Guide
1 GENERAL INFORMATION .............................................................................................................................. 4
1.1 Security Hierarchy......................................................................................................................................................4
1.2 About Your Locking System ........................................................................................................................................5
1.3 Factory Default Settings.............................................................................................................................................5
2 OPERATING THE LOCK................................................................................................................................. 6
2.1 Bank User Group, PIN Positions, and User Codes.........................................................................................................6
2.2 PIN Positions and Access Responsibilities ..................................................................................................................7
2.3 Beeps Patterns...........................................................................................................................................................9
   AdditionalActions/ConditionsforBankModewithKeypadExtension
Additional Actions/Conditions for Service Mode
2.4 User Access Modes and Opening the Lock ..................................................................................................................10
Manager/Employee
Dual Control
Muti-User (default)
Time Delay
2.5 Keypad Input Errors and Clearing the Lock..................................................................................................................11
2.6 Penalty Time (Bank Mode) ...........................................................................................................................................11
2.7 Lockout...................................................................................................................................................................... 11
 2.8 BoltExtensionIndicator .............................................................................................................................................11
2.9 Low Battery Indicator .................................................................................................................................................11
2.10 Changing Batteries..................................................................................................................................................... 11
2.11 iButton Touch Key.......................................................................................................................................................11
3 PROGRAMMING THE LOCK IN BANK MODE .................................................................................................. 12
3.1 Command 22/33: Changing a PIN Code .......................................................................................................................12
3.2 Command 32: Setting the Access Mode ......................................................................................................................12
Enable the Manager/Employee Mode
Enable the Dual Control Mode
Enable Multiple User Mode
Enable the Dual Control Mode 2
3.3 Command 38: Setting the Duress Alarm Feature .........................................................................................................13
Using the Duress Alarm Feature
Enable the Duress Alarm Feature
Disabling the Duress Alarm Feature
3.4 Command 42/43: Verify lock type ...............................................................................................................................14
3.5 Commands 45/54: Lock Initialization for Service Mode Use ........................................................................................14
3.6 Commands 46: Setup Time Delay Override..................................................................................................................15
3.7 Command 47: Set Time Delay Duration........................................................................................................................15
3.8 Command 48: Set Opening Window Duration ..............................................................................................................16
3.9 Command 57: Micro controller reset ...........................................................................................................................16
3.10 Command 73: Set Date - Bank Mode Only ....................................................................................................................16
3.11 Command 74-76: Add or Delete User Positions............................................................................................................17
 3.12 Command77:PINPositionVerication .......................................................................................................................18
3.13 Command 78: Set Time - Bank Mode Only....................................................................................................................18

3
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
 3.14Command79:LockFirmwareVerication...................................................................................................................18
3.15 Command 82: Status Check........................................................................................................................................18
3.16 Command 83: Disable Time Delay Override .................................................................................................................19
 3.17 Command90:LockSerialNumberVerication...........................................................................................................19
 3.18 Command93:AsealVerication .................................................................................................................................19
 3.19 Command96:BatteryVerication ..............................................................................................................................20
 3.20Command97:Time/DateVerication .........................................................................................................................20
3.21 Command 00: Manual Secure Mode ............................................................................................................................20
4 SERVICE MODE OPERATION ........................................................................................................................ 21
4.1 Service Mode Initialization..........................................................................................................................................21
4.2 Service Mode Operation..............................................................................................................................................21
4.3 Service Mode Operation Codes ...................................................................................................................................22
4.4 Open Lock ..................................................................................................................................................................22
Single Control
Single control (15 minute)
Dual Control
4.5 Program Bank Features ..............................................................................................................................................23
4.6 Download Audit Log....................................................................................................................................................23
4.7 Reset User Touch Key:................................................................................................................................................ 23
4.8 Using the Duress Alarm Feature..................................................................................................................................23
4.9 Set Clock Calendar: ....................................................................................................................................................24
Red Manager Key
No Key
4.10 Reset Lockout:...........................................................................................................................................................24
4.11 Revoke Dispatcher: ....................................................................................................................................................24
4.12 Add Dispatcher........................................................................................................................................................... 24
4.13 Un-install Lock:..........................................................................................................................................................24
Table of Contents
Programming and Operations Guide

4
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
1 - General Information
1.1— About Your Locking System
The Model 6128/6129/6106 Electronic Lock has the following hardware components:
6128 /6129 Motorized lock
housed within the safe. Provides for Bank
and Service modes of operation
Keypad
on front of safe door. This is a 12-key
alphanumeric keypad used to enter PIN
codes and programming commands.
6106 Pivot bolt lock
housed within the safe. Provides for Bank
and Service modes of operation
Duress Module (optional)
Housed within the safe. this module
must be connected to the lock to use the
duress alarm feature.
Keypad Extension Base
Installed under the keypad. This is
required when using the lock’s Service
Mode.Theextensionbaseprovidesa
green LED to indicate “Status 1”, and
a red LED to indicate “Status 2” and a
yellow LED to indicate “Mode” of lock
operation.Theextensionbasealso
provides a port for communication with
Touch Keys.
Keypad Extension Base
Eachtimeyoupressanumber,letter,orothercharacteronthekeypad,itbeepsandthekeypad’sredLEDashes.Ifthereisnobeep
orLEDash,checkthebatteriesandtryagain(Seesection2.10—Changing the Batteries).
The # key acts as an enter function and must be used after each code entry.
The * key is used with Programming Command Codes. It may also be used to clear the keypad if there is an input error, by entering
the * key twice.
NOTE:
The lock resonds with different beep sequences to indicate different conditions.
Thebeepsareindicatedintheexamplesbythesymbol♪.Forexample,vebeeps
are indicated by ♪♪♪♪♪. Always wait for each set of beeps to end before entering
another number or letter or you will interrupt the lock’s instructions.

5
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
1.2 — Security Hierarchy
The Model 6128 ATM banking lock system operates in a Bank Mode only, Service Mode only, or both Bank and Service Mode
simultaneously.
Bank Mode Only - Bank users have local control of user PIN positions and codes, and programming through the keypad.
Service Mode Only - Requires the “Lock Management System” for programming Touch Memory Keys and generating one-
time use Operation codes for service users. Bank User PIN codes are disabled.
Bank and Service Mode - Bank users have local control of PIN positions and codes, and limited keypad programming
commands. The “Lock Management System” controls Bank mode optional features and is used for programming Touch
Memory Keys and generating one-time use codes.
1.3 — Factory Default Settings
The 6128/6129 is shipped from Sargent & Greenleaf with factory default settings:
 •BankMode—enabled/notimerestriction.
 •MultipleUserMode—enabled
 •TimeDelay—zero(0)minutes
 •Duress—disabled
 •Auditdownload—enabled
 •SetDate/Time—enabled

6
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
2- Operating the Lock
Positions 00, 02, and 10 have default PIN Codes set at the factory:
Programmer Code (PC) can only set-up the operating parameters of the lock. The Programmer Code cannot open the safe.
BankUserGroupconsistsofupto30PINCodepositions;3Ocersand6Administratorswhomanagethelockprogramsand
up to 20 Users. In total there are 29 codes who open and close the lock.
If the lock still has the original S&G factory default settings, you can open the lock by entering a PIN position and PIN Code,
which makes up an 8-digit User code, followed by the # key.
By default, the lock is set to Multiple User mode which allows opening of the lock by entering any valid code other than the
Programmer Code.
(If lock does not open and beep patterns were heard after pressing the # key, reference section “Beep Patterns” to identify
condition.)
We recommend that Users change their PIN Codes immediately after the PIN positions are assigned.
2.1 — Bank User Group
Bank User Group is the factory default and is always active in each lock (unless disabled under Service Mode operation). The Bank
UserGrouphasanaccesshierarchyofOcers(PINpositions01-03),Administrators(PINpositions04-09),andUsers(PINpositions
10-29).SeeTablesA&Bbeginningonthenextpageforaccessprivileges.
BankUserGroupcanbeconguredtooperateinthreedifferentUseraccessmodes.
Multiple User mode—anyvalidcodeforthelock(otherthantheProgrammerCode)canbeusedtoopenit.
Manager / Employee mode—theOcersorAdministratorsenable/disabletheaccessprivilegeofindividualUserCodes.Whenin
thismodetheocerandAdministratorCodesdonotopenthelock.
Dual Control mode—twoindependentUserCodesareneededtoopenthelock.OcerandAdministratorCodescanbeusedtoopen
the lock in this mode.
PIN Position Description PIN Position Default PIN Code
Programmer Code 00 123456
Ocer Code 02 020202
Ocer Code 10 101010

7
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
2.2— PIN Positions and Access Responsibilities
ThissectiondeneseachPINpositionandtherespectiveUserfunctionsassummarizedinTablesA&B.
PINposition00,theProgrammerposition,canonlycongurethelockanddownloadtheaudittrail.TheProgrammercannotopen
any locks. The Programmer Code is used in conjunction with the Lock Management System to initiate the command to set the lock
into Service Mode of operation.
EachUserisassigneda2-digitPIN(PersonalIdenticationNumber)positionanda6-digitPINCode.ThePINpositionidentiesthe
type of User (Programmer, User, etc.) The PIN Code allows the User to access the lock. Together these two codes form the 8-digit
User Code. Each User can change his own PIN Code but not his PIN position.
Users will always enter both their PIN position and their PIN Code, followed by the # key.
PIN POSITION PIN CODE
Example:02  020202  #
Table A: Programmer Code
Pin Position Position Description Activity
00 Programmer Code Used for initialization of Service Mode with commands 45 and 54.
Used in conjunction with other codes for commands 00,32,38,46,47,48,73,78, and 83.
Cannot open lock.
Cannot add/delete other PIN Codes.
Can change its own PIN code.
Send duress alarm (when programmed).

8
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
Table B: Bank User Group
Pin Position Position Description Access
01 - 03 Ocers •Openthelock(exceptwhenManager/EmployeeModeisenabled).
• Enable and disable Users in Manager/Employee Mode.
• Add new Users
(Requires a second valid User Code).
• Delete Users
(Requires a second valid User Code).
• Start time delay (when programmed).
• Send duress alarm (when programmed).
• Can be a valid second User Code for Dual Control and programming.
• Change their own PIN Code.
04 - 09 Administrators •Openthelock(ExceptwhenManager/EmployeeModeisenabled).
• Enable/disable Users in Manager/Employee Mode.
• Delete Users (requires a second valid User Code).
• Start time delay (when programmed).
• Send duress alarm (when programmed).
• Can be a valid second User Code for Dual Control and programming.
• Change their own PIN Code.
10 - 29 Users • Open the lock
• Start time delay (when programmed).
• Send duress alarm (when programmed).
• Provide second User Code for programming.
• Change their own PIN Code.
•Openthelock(ExceptwhenManager/EmployeeModeisenabled).

9
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
2.3— Beep Patterns (beep1 is the sound emitted when any single button is pressed; beep2 is pitched lower)
The following table lists the beep patterns that will be heard when using the 6128/6129 lock.
(KEB=KeypadExtensionBase,SM=ServiceModeUse).
2.3.1— Additional Actions/Conditions for Bank Mode with Keypad Extension
Action/Condition Tone & Keypad LED KEB LED (if present) Duration
Each Keystroke 1 beep1- 1 cycle
Low Battery 2 beep1Red 5 cycles
Battery too low 20 beep1Red 1 cycle
Start Time Delay 3 quick beep1Red 1 cycle
Time Delay Countdown 1 beep1Red Every 10 sec
Time Delay Expired 10 quick beep1Green 1 cycle
Open Window Countdown 2 beep1Green Every 6 sec.
Bolt Extension 1 beep2+ 1 beep1Red 1 cycle
Code input - Lock in 10-minute penalty time 2 brap - 1 cycle
Code input - Lock Disabled 2 beep2Red 1 cycle
Enable lock (mgr/emp mode) 4 beep1- 1 cycle
Disable lock (mgr/emp mode) 2 beep2- 1 cycle
Access to program modes 5 beep1Green 1 cycle
Program argument conrmation 3 beep1- 1 cycle
Program complete 3 beep1Green 1 cycle
First user entry - dual control 4 beep1Red 1 cycle
Mode 77 - PIN used 1 beep2Red 1 cycle
Mode 77 - PIN empty 1 brap Red 1 cycle
Access granted 3 beep1Green (+ Amber if SM) 1 cycle
Wrong input/Access denied 1 brap Red (+ Amber if SM) 1 cycle
Lock Bolt Bound and Unable to Move 4 brap Red 1 cycle
Time/Date not set before Initialization Attempted 2 brap + 2 brap Red 1 cycle
Attempt to use a disabled touch key 2 beep2Red 1 cycle
Attempt to use a touch key not formatted for system 4 beep2+ 1 brap Red 1 cycle
Action/Condition Tone & Keypad LED KEB LEDs Duration
Touch key read/write error 1 brap Red (+ Amber if SM) 1 cycle
Clock battery too low 2 brap Red/Green alternate cycles

10
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
2.3.2— Additional Actions/Conditions for Service Mode
2.4 - User Access Modes and Opening the Lock
Multiple User—ThelockcanbeopenedbyenteringanyvalidcodeotherthantheProgrammingCode.Iftimedelayis 
 activated,anyvalidcode(excepttheProgrammingCode)canbeenteredtostartthetimedelay.Thenanyvalidcode(except
the Programming Code) can be entered during the opening window to open the lock.
Manager/Employee—TheGroupOcersorAdministratorsenable/disabletheaccesstothelock.Wheninthismode
access is enabled and can be opened by any valid code (not including the Programmer code) until access is disabled.
To enable your lock in Manager/Employee mode
 Enter:AValidOcerorAdministratorcode+#♪♪♪♪
To disable your lock in Manager/Employee mode
 Enter:AValidOcerorAdministratorcode+#♪♪
Dual Control—Twovalidcodesarerequiredtomakeanyprogrammingchangesortoopenthelock.Thesemaybeeither
 UserorOcer/AdministratorCodes.Thesecondcodemustbeenteredwithin60secondsafterentryoftherstcode.If
time delay is activated, only one code is required to start the time delay, but both codes must be entered during the opening
window to open the lock.
Time Delay—Thelockmaybeprogrammedwithatimedelayfrom0-99minuteswithanopeningwindowof1minuteto
10 minutes.
If your lock does not use the time delay
Enter: Your 2-digit PIN position Your 6-digit PIN Code #♪♪♪
After the beeps, turn the safe handle to the unlocked position within 6 seconds.
If your lock uses the time delay
Enter: Your 2-digit PIN position Your 6-digit PIN Code #♪♪♪
The pre-set time delay period begins after you enter your code. During the time delay period, the lock beeps once every
10 seconds. At the end of the time delay, the lock will beep rapidly 10 times to signal the start of the opening window, the
period during which you can open the lock.
During the opening window, the lock beeps twice every 6 seconds.
You must now: Enter: Your 2-digit PIN and Your Your 6-digit User Code again #♪♪♪
Action/Condition Tone & Keypad LED KEB LEDs Duration
Lockout initiated 3 brap Red + Amber 1 cycle
Service Mode initiated Amber Duration of SM Activity
Prompt user for input 1 beep¹ Amber+ashGreen 1cycle-ashuntiltimeout
Secure condition — prompt user 3 beep¹ Amber+ashGreen 1cycle-ashuntiltimeout
Lock initialization successful 1 beep¹ Green + Amber 1 cycle
Lock initialization failed 2 brap Red + Amber 1 cycle

11
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
2.5 - Keypad Input Errors and Clearing the Lock
If you make a mistake while entering a User Code, press * twice at any time to clear the lock and start over. If you hear a single long
beep after entering the # key you have made an error. Press * key twice to clear and try again, or you can wait 10 seconds and the
lock will clear itself.
2.6-Penalty Time (Bank Mode)
If you enter 5 incorrect codes in a row, the lock goes into a 10- minute penalty time and cannot be opened. Once in penalty time,
additional input does not affect the lock or increase the penalty time. You must wait 10 minutes before any valid code entry will be
accepted. If you enter a code (valid or invalid) during the lockout time duration, the lock will emit two long beeps and will not open.
2.7 - Lockout (Service Mode)
Intheunlikelyeventthatthelockisputintopenaltytimevetimesinarow,thelockoutfunctionwillengage.Whenyouattemptto
enter a code, the lock will emit three braps, but will not operate. The lock will have to be reset with a red management key. Contact
your lock software administrator or dispatcher for the proper key and code.
2.8 - Bolt Extension Indicator
Whenthelockboltextendstothelockedposition,youwillhear3beeps(6128/6129)or4beeps(6106).
2.9— Low Battery Indicator
If you enter a correct User Code and hear 5 double-beeps when the lock opens, the batteries are low. Change the batteries.
If the batteries are so low the lock can’t work properly, the lock beeps 20 times when a User code is entered. The lock will not open.
Change the batteries right away and re-enter a User code to open the lock.
The 9V batteries are located behind the keypad.
2.10— Changing the Batteries
The lock will not lose any codes or program settings while you replace the batteries. Your lock uses two 9-volt alkaline batteries. We
recommend Duracell alkaline batteries.
To change the batteries, carefully remove the keypad housing by lifting the bottom edge (closest to
the S&G logo) and easing it off the base. Detach both batteries from the terminals. Insert the new
batteries, supporting the top of each battery holder with your other hand to prevent bending or
breaking the holder.
2.11— iButton Touch Key
IThe touch key allows you to transfer the audit trail from the lock to your computer. The audit trail is a time and date stamped record
of all lock activity. The touch key is also used in the authorization of Service Mode Users at the lock.
The Sargent & Greenleaf Lock Management System software must be installed on your computer
before you can upload and use the audit trail information stored in your lock. For more instructions
on downloading the audit trail.
CAUTION: During normal entry, don’t wait more than 10 seconds between entries or
the lock will clear, and you will have to start over.

12
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3— Programming Commands
3.1— Command 22/33: Changing a PIN Code
Use Command 22/33 to change your own PIN Code. Always change codes with the safe door open. When changing a User Code, you
will enter both the 2-digit PIN position and the 6-digit PIN Code. The PIN position does not change.
To change a PIN Code, perform the following steps
 (APINCodecancontainanynumbers/lettersexcept#or*):
 TrythenewPINCodeatleastthreetimestoconrmoperationbeforeclosingthesafedoor.
3.2— Command 32: Setting the Access Mode
The lock may be set for Multiple User, Manager/Employee, or Dual Control Modes.
Manager/Employee—TheGroupOcersorAdministratorsenable/disabletheaccessofindividualUserCodes.Whenin
 thismode,theGroupOcerandAdministratorCodesdonotopenthelock.
Dual Control—TwovalidUserCodesarerequiredtomakeanyprogrammingchangesortoopenthelock.Thesemay 
 beeitherUserorManagerCodes.Thesecondcodemustbeenteredwithin60secondsafterentryoftherstcode.Iftime
delay is activated, only one code is required to start the time delay, but both codes must be entered during the opening
window to open the lock
Multiple User—Thelockcanbeopenedbyenteringanyvalidcode,exceptfortheProgrammingCode.
Enable the Manager/Employee Mode
Set the lock into Manager/Employee mode by performing the following steps:
Enable the Dual Control Mode
The lock may be set for Dual Control mode operation requiring two valid combinations to gain access to the secured arear. Change to dual
control by performing the following steps:
Process Changing the default ocer code
1) Enter: 22* or 33* 1) Enter: 22*
2) Enter: Current Code + # ♪♪♪♪♪ 2) Enter: 02020202 # ♪♪♪♪♪
3) Enter: New Code +# ♪♪♪ 3) Enter: 02695847 # ♪♪♪♪♪
4) Enter: New Code + # ♪♪♪ 4) Enter: 02695847 # ♪♪♪
Process Enabling Manager/Employee mode
1) Enter: 32* 1) Enter: 32*
2) Enter: Programmer Code + # ♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Ocer code +# ♪♪♪♪♪ 3) Enter: 02020202 # ♪♪♪♪♪
4) Enter: 2 (Function Number) + #♪♪♪ 4) Enter: 2 # ♪♪♪
5) Enter: 2 (Function Number) + #♪♪♪ 5) Enter: 2 # ♪♪♪
Process Enabling Dual Control Mode
1) Enter: 32* 1) Enter: 32*
2) Enter: Programmer Code + # ♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Ocer code +# ♪♪♪♪♪ 3) Enter: 02020202 # ♪♪♪♪♪
4) Enter: 3 (Function Number) + #♪♪♪ 4) Enter: 3 # ♪♪♪
5) Enter: 3 (Function Number) + #♪♪♪ 5) Enter: 3 # ♪♪♪

13
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
Enable the Multiple User Mode
The lock may be set for Multi-User operation requiring one valid user code to gain access to the secured area. Change to Multi-User mode
by performing the following steps:
3.3 — Command 38: Setting the Duress Alarm Feature
The model 6128/6129 lock has an optional duress, or silent alarm, option. The optional duress module must be connected to the lock
and your alarm system for this feature to work.
Using the Duress Alarm Feature
To send a duress alarm to the alarm center, enter a User Code that is one number higher or lower on the last digit of a User’s
normal PIN Code and press the # key.
 Forexample,ifthenormalUserCodeis123456forPINposition02,theUsercanactivatetheduressalarmbyentering02123455or
02123457, followed by #. If the User Code ends in 0, use 1 or 9 to activate the duress alarm. The lock will operate normally when a Duress
code is entered.
All User Codes can send the duress signal at any time. It can also be sent during programming sequences.
Enable the Duress Alarm Feature
After the lock is installed with the module, the duress feature must be enabled by performing the following steps:
Enable the Duress Alarm Feature
After the lock is installed with the module, the duress feature must be enabled by performing the following steps:
Process Create a code in pin 12
1) Enter: 38* 1) Enter: 38*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: 1(function number) + # ♪♪♪ 3) Enter: 1 # ♪♪♪
4) Enter: 1(function number) + #♪♪♪ 4) Enter: 0 #♪♪♪
Process Create a code in pin 12
1) Enter: 38* 1) Enter: 38*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: 0(function number) + # ♪♪♪ 3) Enter: 0 # ♪♪♪
4) Enter: 0(function number) + #♪♪♪ 4) Enter: 0 #♪♪♪
Process Enabling Multiple User Mode
1) Enter: 32* 1) Enter: 32*
2) Enter: Programmer Code + # ♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Ocer code +# ♪♪♪♪♪ 3) Enter: 02020202 #♪♪♪♪♪
4) Enter: 4 (Function Number) + #♪♪♪ 4) Enter: 3 # ♪♪♪
5) Enter: 4 (Function Number) + #♪♪♪ 5) Enter: 3 # ♪♪♪

14
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3.4 — Command 42/43: Identifying the Type of Lock /Lock Mechanics
At times, a service technician may need to know the type of lock is mounted on the safe door.
To identify the lock type, perform this step:
Enter 42* on the keypad and listen for the beeps. (Low - >High-> Low [pause] High = A-Series Lock )
To identify the lock type, perform this step:
Enter 43* on the keypad and listen for the beeps. Use the table below to determine the type of lock.
3.5— Commands 45/54: Service Mode Initialization (Single and Multiple):
TosuccessfullyoperatethelockinServiceMode,thelockmustrstbeinitialized.Akeypadextensionwithtouchkeyreadermustbe
connected to the lock. Lock initialization requires a management touch key prepared by the primary service company’s LMS system.
This touch key will have been prepared for either single or multiple mode. It is important for the key provider to advise whoever is
performing initialization at the lock which mode is being used.
The management touch key is used in conjunction with a keypad command to initialize the lock. Lock initialization can only be
completed after the date and time are set. If initialization is attempted before time and date are set, the lock will sound 2 sets of
2 long beeps (braps). Always use local standard time at the lock’s location. Adjust the time 1 hour back if lock location observes
daylight savings.
Theserialnumberusedfortheinitializationprocessismaintainedinthelockrmware.Theserialnumbercannotbechange.If
the key is programmed with the incorrect serial number when trying to utilize the single initialization process, the lock will fail to
initialize. The key is not programmed with serial number information when performing the multiple initialization process.
To initialize multiple locks (Command 45):
1) Set the date & time using the 73* command and 78* command.
 2)SnaptheManagementtouchkeyintothekeypadextensionreceptacle.
3) Enter: 45* 00123456 # (default Programmer Code or the current Programmer Code).
 4)TheAmber“Mode”lightonthekeypadextensionbasewillremainlitduringtheinitializationprocess.
 5)Uponthesuccessfulinitialization,theGreen“Status1”indicatorwillashandthekeypadwillemitthreebeeps.Iftheinitializationfails
the Red “Status 2” indicator will illuminate, and the lock will emit one long beep.
To initialize one lock (Command 54):
1) Set the date & time using the 73* command and 78* command.
 2)SnaptheManagementtouchkeyintothekeypadextensionreceptacle.
3) Enter: 54* 00123456 # (default Programmer Code or the current Programmer Code).
 4)TheAmber“Mode”lightonthekeypadextensionbasewillremainlitduringtheinitializationprocess.
 5)Uponthesuccessfulinitialization,theGreen“Status1”indicatorwillashandthekeypadwillemitthreebeeps.Iftheinitializationfails
the Red “Status 2” indicator will illuminate, and the lock will emit one long beep.
Beep Set Number of Beeps Number of Beeps Number of Beeps
1st set (low pitch) 1 1 1
2nd set (high pitch) 1 1 1
3rd set (low pitch) 1 1 1
4th set (high pitch 3 4 1
Type of Lock 6128: Deadlocking Bolt 6129: Push/Pull Bolt 6106: Pivot Bolt

15
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3.6 — Command 46: Setting Up the Time Delay Override Options
When the time delay feature is enabled, the A-Series lock can be programmed with a time delay override (TDO) feature that will allow
aspecicusertobypassthetimedelaycountdown.ThetimedelayoverridecodemustalwaysbesetupinPINposition29.
TherearetwotypesofTDOavailable.TDOTYPE1requiresthatthetimedelayoverridecodeisenteredwithintherstminuteofthe
time delay countdown. In other words, a User must start the time delay countdown by entering their code. If the time delay override
codeisenteredwithintherstminute,thenthelockwillopen.
Delay override feature must be made during the opening window. If a time delay value has already been entered, then any changes
notes below:
TDO TYPE 2 will allow the lock to be opened by the time delay override code without requiring another User start the time delay
countdown.
Set time delay override
 Ifthetimedelayhasalreadybeenset,enteraUserCodetostartthetimedelay.Whenthetimedelayexpires(thelockemits10rapid
beeps) and the opening window has begun, immediately proceed to change the time delay override by performing the following steps:
The TDO TYPE 2 function has now been enabled. The code in position 29 can now be used to open the lock without waiting for the time
delay countdown.
3.7 — Command 47: Setting Up the Time Delay
The 6128/6129/6106 can be programmed with a time delay feature. Time delay applies to Bank Users only. The time delay can be set
from0to99minutes.TheLEDredlightonthekeypadashesandasinglebeepsoundsevery10secondsasareminderthatthelock
is in the time delay period.
To open the lock, a User must enter their User Code to start the time delay period, wait the length of the time delay period and then
enter a valid User Code during the opening window.
If the lock is not opened during the open window, it resets, and the process must be restarted.
The 6128/6129/6106 comes from the factory with no time delay set.
Process Set TDO 0/1/2
1) Enter: 46* 1) Enter: 46*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Time Delay Override Type (0/1 2)) + # ♪♪♪ 3) Enter: 0/1/2 # ♪♪♪
4) Enter: Time Delay Override Type (0/1/ 2)) + #♪♪♪ 4) Enter: 0/1/2 #♪♪♪
NOTE:
If a time delay value has already been entered, then any changes to the time delay
override feature must be made during the opening window.
NOTES:
1) If the time delay has already been set, changes to the opening window and time
delay duration can only be made during the opening window.
2) IMPORTANT:Donotsetthetimedelayuntilyouhavenishedallother 
programming functions, or you will have to wait through the time delay before
making any other programming If changes.

16
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
Set time delay duration
 Ifthetimedelayhasalreadybeenset,enteraUserCodetostartthetimedelay.Whenthetimedelayexpires(thelockemits10rapid
beeps) and the opening window has begun, immediately proceed to change the time delay by performing the following6 steps:
3.8— Command 48: Setting Up the Opening window
Whenatimedelayexpires,thelockemits10rapidbeepstoindicatethatitcannowbeopened.Thisperiodoftimeiscalledthe
“openingwindow”.Whenthelockhasenteredit’sopeningwindow,thelockwillbeepandtheLEDashestwiceevery10seconds.
The opening window factory default is set for 2 minutes, and the opening window can be set from 1 to 10 minutes.
Changing the Opening window Duration
 Ifthetimedelayhasalreadybeenset,enteraUserCodetostartthetimedelay.Whenthetimedelayexpires(thelockemits10rapid
beeps) and the opening window has begun, immediately proceed to change the time delay by performing the following steps:
3.9 — Command 57: Microcontroller Reset
Thiscommandisusedtoresetthemicrocontrollerinsidethelockwithoutremovingpower.Simplypress57*.Thekeypadextension
LEDswillallashmomentarily.Nocodeorprogramminginformationinthelockwillbealtered.
3.10 — Command 73: Set Date - Bank Mode Only
The date should be entered in DDMMYY format, where DD = day, MM = month, and YY = year. The Date should be set prior to initializing
the lock for Service Mode use. To set the date, perform the following steps:
Process Set a 5-minute opening window
1) Enter: 48* 1) Enter: 48*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Opening window Minutes (0-10) + # ♪♪♪ 3) Enter: 5 # ♪♪♪
4) Enter: Opening window Minutes (0-10) + #♪♪♪ 4) Enter: 5 #♪♪♪
Process Set a date of January 18, 2022
1) Enter: 73* 1) Enter: 73*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Ocer code +# ♪♪♪♪♪ 3) Enter: 02020202 # ♪♪♪♪♪
4) Enter: Date(ddmmyy) + #♪♪♪ 4) Enter: 180122 #♪♪♪
5) Enter: Date(ddmmyy)+ #♪♪♪ 5) Enter: 180122 #♪♪♪
Process Set a 5-minutes time delay
1) Enter: 47* 1) Enter: 47*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Time delay Minutes (0-99) + # ♪♪♪ 3) Enter: 5 # ♪♪♪
4) Enter: Time delay Minutes (0-99) + #♪♪♪ 4) Enter: 5 #♪♪♪

17
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3.11 — Add or Delete Code Positions
74 command: Add a New User Position
To add User positions, perform the following steps:
We recommend that each User change his or her PIN Code using Command 22.
74 command: delete a User
To delete user positions, perform the following steps:
75 command: Add a New User Position
To add User positions, perform the following steps:
We recommend that each User change his or her PIN Code using Command 22.
76 command: delete a User
To delete user positions, perform the following steps: To add User positions, perform the following steps:
We recommend that each User change his or her PIN Code using Command 22.
Process Delete a code in pin 12
1) Enter: 74* 1) Enter: 74*
2) Enter: Ocer Code + #♪♪♪♪♪ 2) Enter: 02020202 # ♪♪♪♪♪
3) Enter: A valid second code + #♪♪♪♪♪ 3) Enter: 10101010 # ♪♪♪♪♪
4) Enter: User position + #♪♪♪ 4) Enter: 12 #♪♪♪
5) Enter: User Position + #♪♪♪ 5) Enter: 12 #♪♪♪
Process Create a code in pin 13
1) Enter: 75* 1) Enter: 75*
2) Enter: Ocer Code + #♪♪♪♪♪ 2) Enter: 02020202 # ♪♪♪♪♪
3) Enter: empty pin position +#♪♪♪♪♪ 3) Enter: 13 # ♪♪♪♪♪
4) Enter: A new 8-digit code + #♪♪♪ 4) Enter: 13131313 # ♪♪♪
5) Enter: Conrm 8-digit code+ #♪♪♪ 5) Enter: 13131313 #♪♪♪
Process Delete a code in pin 13
1) Enter: 76* 1) Enter: 76*
2) Enter: Ocer Code + #♪♪♪♪♪ 2) Enter: 02020202 # ♪♪♪♪♪
3) Enter: pin position + #♪♪♪♪♪ 3) Enter: 13 # ♪♪♪♪♪
4) Enter: #♪♪♪ 4) Enter: # ♪♪♪
5) Enter: #♪♪♪ 5) Enter: # ♪♪♪
Process Create a code in pin 12
1) Enter: 74* 1) Enter: 74*
2) Enter: Ocer Code + #♪♪♪♪♪ 2) Enter: 02020202 # ♪♪♪♪♪
3) Enter: A valid second code +#♪♪♪♪♪ 3) Enter: 10101010 # ♪♪♪♪♪
4) Enter: A new 8-digit code + #♪♪♪ 3) Enter: 10101010 #♪♪♪
5) Enter: Conrm 8-digit code+ #♪♪♪ 5) Enter: 10101010 #♪♪♪

18
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3.12— Command 77: PIN Position Verication
UsethiscodetoverifythataUserhasbeenassignedtoaPINposition.Forexample,itwilltellyouwhetherPIN07hasaPINCodein
this position.
Step 1. Enter: 7 7 *
Step 2. Enter:PINpositiontobeveriedand#
Onebrap(longbeep)meansthepinpositionisempty.Onelow(shortbeep)meansthepinpositionislled.
Pin position response
3.13— Command 78: Set Time – Bank Mode Only
The time should be set in HHmm format based on a 24-hour clock, where HH = hours and mm = minutes. The time should beset prior
to initializing the lock for Service Mode use. The time is to always be set in the local standard time for use in Service Mode. Local
standard time must be set even though daylight savings time may be in effect. To set time perform the following steps:
3.14 — Command 79: Firmware verication
Thiscommandallowseldpersonnelallowstheeldpersonneltoassesstheversionofrmwarethelockhasbeenprogrammed.
3.15 — Command 82: Status Check
Thiscommandallowseldpersonneltoplaceatouchkey(userofmanagerkey)ontothekeypadextensionandinput82*.Thelock
will write an audit trail event to the touch key indicating the lock ID and current time/date stored in the lock. The lock will emit 3
beeps after writing the even to the key.
If the 8 2 * command is used with a touch key that is disabled, the lock will emit 2 low beeps, but will still write the event to the touch
key and then emit 3 standard beeps.
If the 8 2 * command is used with a touch key that is not formatted for the system to which the lock belongs, the lock will emit 4 low
beeps, but will still write the event to the touch key and then emit 3 standard beeps.
Enter: 8 2 * Wait for the lock to emit 3 standard beeps before removing the touch key.
77* 00# 1 low Filled
77* 01# 1 Brap Empty
77* 01# 1 low Filled
Process Set 5:45 PM
1) Enter: 78* 1) Enter: 78*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: Ocer Code + #♪♪♪♪♪ 3) Enter: 02020202 # ♪♪♪♪♪
4) Enter: Standard Time (mmhh) + #♪♪♪ 4) Enter: 1745 # ♪♪♪
5) Enter: Standard Time (mmhh) + #♪♪♪ 5) Enter: 1745 # ♪♪♪
NOTES:
1) The 74 command (Add and Delete) code process require the input of a second valid combination.
2) The 75 command (Add) code process does not require the input of a second valid combination.
3) The 76 command (Delete) code process does not require the input of a second valid combination

19
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3.16 — Command 83: Disable Time Delay Override
If you do not want the Time Delay Override (TDO) function available, it can be permanently disabled, and all of the time delay override
commands will no longer work.
Disable time delay override
3.17 — Command 90: Lock Serial Number Verication
The A-Series lock serial number can be audibly retrieved when visual indicators are not available. The lock will give a low beep for the
number 0 and 1 beep counting up any number great than 0. The lock will pause between each number. You can verify the lock serial
number using the following process.
Enter: 90* on the lock keypad.
LSN: 50013968
3.18 — Command 93: Aseal Code Verication
The A-Series lock’s Aseal close code can be audibly retrieved when there is not any visual indicator available. The lock will give a low
beep for the number 0 and 1 beep counting up any number great than 0. The lock will pause between each number. You can verify the
lock serial number using the following process.
Enter: 93* on the lock keypad.
Aseal 103968
Process Set a 5-minutes time delay
1) Enter: 83 * 1) Enter: 83**
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: 1 (conrm TDO disable) + #♪♪♪ 3) Enter: 1 #♪♪♪
4) Enter: 1 (conrm TDO disable) + #♪♪♪ 4) Enter: 1 # ♪♪♪
5 5 high beeps
0 1 low beep
0 1 low beep
1 1 high beep
3 3 high beeps
9 9 high beeps
6 6 high beeps
8 8 high beeps
1 1 high beep
0 1 low beep
3 3 high beeps
9 9 high beeps
6 6 high beeps
8 8 high beeps
NOTES:
Once the TDO features have been disabled using command 83, there is no way to ever use time delay
override with the lock changes window.
Once the Programmer code has been changed, TDO disable option is no longer available.

20
Sargent and Greenleaf Revision 02/15/2022 Document: 630-600
3.19 — Command 96: Battery Verication
The A-Series lock’s Battery health can be audibly retrieved. The battery health is measured in terms Good, Should be Replaced and
Bad.
• Good batteries indicates the lock is operating properly.
• Should be replaced means the lock is operating but batteries should be replaced soon.
• Bad indicates the lock is not operating properly and batters must be replaced before continuing.
You can verify the lock’s battery health serial using the following process.
Enter: 96* on the lock keypad
Battery health
3.20 — Command 97: Date Verication
The A-Series lock’s time and date settings can be audibly retrieved when there is not any visual indicator available. The lock will give
a series of low beep and high beeps that represent the lock format of DDMMYY HHmm. You can verify the lock time and date setting
by using the following process.
Enter: 97* on the lock keypad
DATE:23/01/22 11:23 AM
3.21 — Command 00: Manual secure mode.
TheA-Serieslockcanbeconguredtooperatea“ManualSecureMode.”INthismode,itrequirestheusertoenterthe00#toobtain
boltextensionafterasuccessfulboltretraction.Themodeisintendedtomimictheoperationofamanualdiallock.Tosetthelock
in manual secure mode, use the following process.
3 beeps Good
5 sets of 2 beeps Should be replaced
20 beeps Bad
23 2 low, 3 high
01 1 low, 1 high
22 2 low, 2 high
9 1 low, 1 high
11 1 low, 1 high
23 2 low, 3 high
Process Set mode on/off
1) Enter: 00* 1) Enter: 00*
2) Enter: Programmer Code + #♪♪♪♪♪ 2) Enter: 00123456 # ♪♪♪♪♪
3) Enter: 1/0 (on/off) + #♪♪♪ 3) Enter: 1/0 (on/off) + # ♪♪♪
4) Enter: 1/0 (on/off) + #♪♪♪ 4) Enter: 1/0 (on/off) + # ♪♪♪