Sauder 415137 User manual

Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 354959 08 / 30 / 13
Date Purchased: ____________________
English.................... Page 1-14
Français...............Pages 15-16
Espanol.............Páginas 17-18
PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
415137
Queen Footboard with Rails
Carson Forge Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification.......................2
Hardware Identification .............3
Assembly Steps....................4-14
Français..............................15-16
Espanol...............................17-18
Warranty...................................19
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D PANEL 1
E LOWER PANEL 1
F LEG 2
G BED RAIL 2
H TOP MOLDING 1
I SLAT SUPPORT 2
J CENTER SLAT SUPPORT 1
K SLAT 6
L SUPPORT FOOT 2
Page 2 www.sauder.com/services 415137
A
B
CD
E
F
G
H
I
J
K
L
G
I
LK
K
K
K
K
F

Screws are shown actual size. You may receive extra hardware with your unit.
Page 3
www.sauder.com/services415137
HARDWARE IDENTIFICATION:
CAM DOWEL - 6
2F
CAM SCREW - 10
8F
HIDDEN CAM - 16
1F
BROWN 1-1/2" FLAT HEAD SCREW - 34
14S
BLACK 1-1/4" FLAT HEAD SCREW - 8
7S
84S BLACK 3” PAN HEAD SCREW - 6
BLACK 1-7/8" FLAT HEAD SCREW - 12
2S
CAM COVER - 10
12P
SILVER 1-1/8" FLAT HEAD SCREW - 6
10S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), PANEL (D), and CENTER SLAT SUPPORT (J). Then, insert the
metal end of six CAM DOWELS (2F) into each HIDDEN CAM on the long edges of the PANEL (D) and the short edges of
the ENDS (A and B).
Page 4 www.sauder.com/services 415137
(16 used)
(6 used)
Arrow
1F
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
D
J
Do not insert CAM
DOWELS into this edge.
Do not insert
CAM DOWELS
into this edge.
Do not insert CAM
DOWELS into this part.
Do not insert CAM
DOWELS into the
long edges.

2
2
S
t
e
p
Page 5
www.sauder.com/services415137
A
B
F
E
F
8F (10 used)
Insert ten CAM SCREWS (8F) into the ENDS (A and B), LOWER PANEL (E), and LEGS (F).

3
3
S
t
e
p
Page 6 www.sauder.com/services 415137
D
C
Surface with
HIDDEN CAMS
Flat edge
D
A
B
Surface with
HIDDEN CAMS
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
Fasten the ENDS (A and B) to the PANEL (D) as shown in the lower diagram. Tighten four HIDDEN CAMS.
Fasten the ENDS (A and B) and the PANEL (D) to the TOP (C) as shown in the upper diagram. Tighten six HIDDEN CAMS.
S
urface with holes
Surface without
HIDDEN CAMS
Holes are closer
to this edge.
Surface with
HIDDEN CAMS
Holes are closer
to this edge.
Edge with
CAM
DOWELS

4
4
S
t
e
p
Page 7
www.sauder.com/services415137
D
G
G
Surface with more holes
Surface with fewer holes
Fasten the BED RAILS (G) to the PANEL (D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Fasten the BED RAILS (G) to the ENDS (A and B). Use six SILVER 1-1/8" FLAT HEAD SCREWS (10S).
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
SILVER 1-1/8" FLAT HEAD SCREW
(6 used in this step)
10S
For support, place packing
foam or blocks under the
BED RAILS (G).
These holes
should be here.
A
B

5
5
S
t
e
p
Page 8 www.sauder.com/services 415137
I
G
G
I
Fasten the SLAT SUPPORTS (I) to the BED RAILS (G). Use twelve BROWN 1-1/2" FLAT HEAD SCREWS (14S).
14S
BROWN 1-1/2" FLAT HEAD SCREW
(12 used in this step)
These holes
should be here.
Edge with
no holes
Edge with
no holes

6
6
S
t
e
p
Page 9
www.sauder.com/services415137
Fasten the TOP MOLDING (H) to the LOWER PANEL (E). Use four BROWN 1-1/2" FLAT HEAD SCREWS (14S).
Fasten the LOWER PANEL (E) to the BED RAILS (G) and SLAT SUPPORTS (I). Use six BLACK 1-7/8" FLAT HEAD
SCREWS (2S).
EG
G
H
I
14S
BROWN 1-1/2" FLAT HEAD SCREW
(4 used in this step)
BLACK 1-7/8" FLAT HEAD SCREW
(6 used in this step)
2S
Rounded
edge
CAM
DOWELS
should be here.
I

7
7
S
t
e
p
Page 10 www.sauder.com/services 415137
Fasten the SUPPORT FEET (L) to the CENTER SLAT SUPPORT (J). Use eight BLACK 1-1/4" FLAT HEAD SCREWS (7S).
BLACK 1-1/4" FLAT HEAD SCREW
(8 used in this step)
7S
J
L
L
These holes
should be here.
Surface with HIDDEN CAMS