Sauder Cannery Bridge 429512 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 570162 07/14/21
Purchased: __________________
Hutch
Cannery Bridge Collection | Model 429512
Knick-knack
paddywhack,
give your stu a home.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Table of Contents Assembly Tools Required
Page 2 www.sauder.com/service 429512
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
3
4
5
6-28
29-32
33-36
37-38
39
Pencil
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Scissors
Masking Tape

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C TOP (1)
D BOTTOM (1)
E UPRIGHT (1)
F TOP BRACE (1)
G BOTTOM BRACE (1)
H LEFT DOOR (2)
J RIGHT DOOR (2)
K SMALL BACK (1)
L LARGE BACK (1)
Page 3www.sauder.com/service429512
A
B
C
D
E
F
G
H
J
K
L
H
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/service 429512
1/2" PAN HEAD SCREW - 12
13 3/4" PAN HEAD SCREW - 8 14
HIDDEN CAM - 16
2
WOOD DOWEL - 27
1CAM SCREW - 16
34KNOB - 4
6NAIL - 20 TIE PLATE - 2
7DOOR STOP - 2
85 HINGE - 8
FURNITURE TIPPING
RESTRAINT KIT - 2
96
APPLIQUE CARD - 2
9BUMPER CARD - 2 10
2" FLAT HEAD SCREW - 16
11 1/2" FLAT HEAD SCREW - 16
12
2-1/2" FLAT HEAD SCREW - 2
15 7/8" MACHINE SCREW - 4 16

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service429512

Step 1
å NOTE: You will need someone's help later in assembly.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: Save some packing foam for support to be used
during the assembly.
å Turn four CAM SCREWS (3) into the TOP BRACE (F).
å Push ten HIDDEN CAMS (2) into the TOP (C) and
TOP BRACE (F).
å NOTE: Be sure the HIDDEN CAMS are completely
inserted into the holes.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
Page 6 www.sauder.com/service 429512
1
2
Arrow
Arrow
2
2
Arrow
3
C
F
Remember:
Righty tighty.
Lefty loosey.

Step 2
å Fasten two DOOR STOPS (8) to the TOP BRACE (F). Use four 1/2" PAN
HEAD SCREWS (13).
å NOTE: The DOOR STOPS will overhang the edge of the BRACE.
å Insert three WOOD DOWELS (1) into the TOP BRACE (F).
å Fasten the TOP BRACE (F) to the TOP (C). Tighten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the BRACE insert into the TOP.
Page 7www.sauder.com/service429512
1
C
F
F
8
These surfaces
should be even.
1
1/2" PAN HEAD SCREW
(4 used in this step)
13
Surface with
HIDDEN CAMS

å Insert two WOOD DOWELS (1) into the TOP (C).
å Fasten the UPRIGHT (E) to the TOP (C). Use two 2" FLAT
HEAD SCREWS (11).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the TOP insert
into the UPRIGHT.
Step 3
Page 8 www.sauder.com/service 429512
For support, place packing
foam or books here.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
1
2" FLAT HEAD SCREW
(2 used in this step)
11
C
F
Surface with
HIDDEN CAMS
Notch
E

å Push four HIDDEN CAMS (2) into the SMALL BACK (K).
å Insert three WOOD DOWELS (1) into the TOP (C).
å Fasten the SMALL BACK (K) to the TOP (C). Use four 2" FLAT HEAD SCREWS (11).
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the TOP insert into the BACK.
Step 4
Page 9www.sauder.com/service429512
2
Arrow
Arrow
2
1
K
Surface with
HIDDEN CAMS
K
C
2" FLAT HEAD SCREW
(4 used in this step)
11
Closer together
Farther apart
1

å Turn six CAM SCREWS (3) into the RIGHT END (B).
å Insert four WOOD DOWELS (1) into the RIGHT END (B).
å Fasten the RIGHT END (B) to the TOP (C), TOP BRACE (F),
and SMALL BACK (K). Tighten five HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the END insert into the
TOP and BACK.
Step 5
Page 10 www.sauder.com/service 429512
1
3
C
F
K
B
B
1
1