Sauder County Line 415996 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-18
Français pg 19-21
Español pg 22-24
Lot # 357665 12/13/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
4-Drawer Chest
County Line Collection | 415996
Stu a sock in it.
Or two.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4
5-18
19-21
22-24
25-26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
415996 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BACK (2)
F DRAWER BRACE (4)
G FRONT LEG (2)
H BACK LEG (2)
I DRAWER FRONT (4)
J TOP MOLDING (1)
K BOTTOM MOLDING (1)
D50 RIGHT DRAWER SIDE (4)
D51 LEFT DRAWER SIDE (4)
D175 DRAWER BACK (4)
D983 DRAWER BOTTOM (4)

Part Identification
415996www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
D50
E
G
H
D51
D175
D983

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
415996 www.sauder.com/servicesPage 4
5L WARNING LABEL - 1
(Refer to the last step for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
40CA CABINET RIGHT - 4 40CB CABINET LEFT - 4 40CC DRAWER RIGHT - 4 40CD DRAWER LEFT - 4
SAFETY BRACKET - 1
1G ANGLE BRACKET - 3
27G
BLACK 9/16" LARGE HEAD SCREW - 23
1S
WASHER - 8
10I
BLACK 2-1/4" FLAT HEAD SCREW - 9
26S
10F TWIST-LOCK®FASTENER - 8
SILVER 1/4" MACHINE SCREW - 8
61S
3S GOLD 5/16" FLAT HEAD SCREW - 32
METAL PIN - 4
1R
CAM SCREW - 12
8F WOOD DOWEL - 2 15F
30S BLACK 1-9/16" FLAT HEAD SCREW - 24
HIDDEN CAM - 12
1F
PULL - 4
98K
DRAWER FRONT
BRACKET - 4
9G

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
415996www.sauder.com/services Page 5
10F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (10F) into the large holes in the ENDS (A
and B) and BOTTOM (D).
A
B
D
10F

Step 2
415996 www.sauder.com/servicesPage 6
å Turn twelve CAM SCREWS (8F) into the exact holes
shown in the FRONT LEGS (G) and DRAWER FRONTS (I).
å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B)
and DRAWER BRACES (F).
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
B
F
G
I
G
F
F
F
I
I
I
(12 used)
8F
(12 used)
1F
Arrow
Turn the CAM SCREWS
into the exact holes shown.

å Insert two WOOD DOWELS (15F) into the ENDS (A and B).
å Fasten the FRONT LEGS (G) to the ENDS (A and B).
Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the holes in the FRONT LEGS.
Step 3
415996www.sauder.com/services Page 7
15F
A
B
G
G
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces must be even.
These surfaces must be even.
15F
1
2
The LEG should
overhang this edge.

å Fasten the BACK LEGS (H) to the ENDS (A and B). Use
eight BLACK 2-1/4" FLAT HEAD SCREWS (26S).
Step 4
415996 www.sauder.com/servicesPage 8
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
H
H
BLACK 2-1/4" FLAT HEAD SCREW
(8 used in this step)
26S
These surfaces must be even.
The LEG should
overhang this edge.

Step 5
415996www.sauder.com/services Page 9
å Fasten the CABINET RIGHTS (40CA) and CABINET
LEFTS (40CB) to the ENDS (A and B). Use sixteen GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4.
1
3
4
1
2
34
A
B
1
2
34
1
2
34
1
2
34
2
1
3
4
2
1
3
4
2
1
3
4
2
Roller end
GOLD 5/16" FLAT HEAD SCREW
(16 used in this step)
3S
Roller end

Step 6
415996 www.sauder.com/servicesPage 10
å Fasten the LEFT END (B) to the TOP (C). Tighten two
TWIST-LOCK® FASTENERS.
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
B
Surface
with
HIDDEN
CAMS
G
C
Surface with holes
Long finished edge