Sauder Barrister Lane 414724 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Case your joint.
Bookcase
Barrister Lane Collection | Model 414724
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-16
Français pg 17-18
Español pg 19-20
Lot # 362635 06/17/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-16
17-18
19-20
21-22
23
414724 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D UPPER UPRIGHT (2)
E LOWER UPRIGHT (2)
F TOP (1)
G BOTTOM (2)
H SHELF (4)
I BACK (2)
J FRONT SKIRT (1)
K SIDE SKIRT (2)
L SIDE RAIL (2)
M BACK RAIL (1)
N FRONT MOLDING (1)
O RIGHT MOLDING (1)
P LEFT MOLDING (1)
Q SHELF MOLDING (2)
A
B
C
D
D
E
E
F
G
G
H
H
H
H
I
I
J
K
K
L
L
M
N
O
P
Q
Q
414724www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SAFETY BRACKET - 1
1G ANGLE BRACKET - 6
27G
BLACK 9/16" LARGE HEAD SCREW - 13
1S BLACK 1-7/8" FLAT HEAD SCREW - 18
2S
36P CAM COVER - 6
12S BROWN 1" FLAT HEAD SCREW - 13
SCREW COVER - 5
18P METAL PIN - 8 1R
MOLDING
CONNECTOR - 2
19F
NAIL - 91
1N
HIDDEN CAM - 38
1F CAM DOWEL - 38 2F
CARD HOLDER - 8
35M
CARD SHEET - 1
38M
SILVER 3/8" MACHINE SCREW - 16
97S
414724 www.sauder.com/servicesPage 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty-eight HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHT (C), BOTTOMS (G), and SHELVES (H).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
414724www.sauder.com/services Page 5
Arrow
1F
2F
Arrow
1F
2F
(38 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
C
B
A
H
H
H
HG
G

å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (N, O, and P).
Step 2
414724 www.sauder.com/servicesPage 6
Flat end
Flat end
N
N
O
P
P
19F
19F
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.

å Fasten the RAILS (L and M) to the TOP (F). Use nine
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 3
414724www.sauder.com/services Page 7
F
L
L
M
Surface with
fewer holes
BLACK 1-7/8" FLAT HEAD SCREW
(9 used in this step)
2S
Finished surface
Long finished edge
Remember:
Righty tighty.
Lefty loosey.

å Carefully turn your TOP over.
å Fasten the MOLDINGS (N, O, and P) to the TOP (F). Use
nine BROWN 1" FLAT HEAD SCREWS (12S).
å NOTE: Do not overtighten the SCREWS into the TOP.
Step 4
414724 www.sauder.com/servicesPage 8
Long finished edge
Surface with more holes
F
N
O
P
BROWN 1" FLAT HEAD SCREW
(9 used in this step)
12S
Do not overtighten
the SCREWS (12S).

å Fasten the UPRIGHT (C) to the TOP (F). Tighten two
HIDDEN CAMS.
å Insert four METAL PINS (1R) into the UPPER UPRIGHTS (D).
å Insert the METAL PINS (1R) in the end of the UPPER
UPRIGHTS (D) into the holes in the TOP (F).
Step 5
414724www.sauder.com/services Page 9
Surface with
more holes
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
1R
Long finished edge
C
D
D
F
Finished edge
Surface with
HIDDEN CAMS

BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
å Fasten two SHELVES (H) to the UPRIGHT (C). Tighten
four HIDDEN CAMS.
å Fasten the SHELVES (H) to the UPPER UPRIGHTS (D).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å Insert four METAL PINS (1R) into the LOWER UPRIGHTS (E).
å Insert the METAL PINS (1R) in the end of the LOWER
UPRIGHTS (E) into the holes in the SHELVES (H).
Step 6
414724 www.sauder.com/servicesPage 10
C
D
D
E
E
H
H
1R
1R
Finished edge
Finished edge
Arrow
Minimum
190 degrees
Maximum
210 degrees
Long edge with
HIDDEN CAMS