Sauder HomePlus 411965 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Store behind
closed doors.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-36
Français pg 37-40
Español pg 41-44
Lot # 358635 01/22/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Storage Cabinet
HomePlus Collection | Model 411965
sauder.com

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Electric Drill with 1/4" bit
2-3
3-4
5-36
37-40
41-44
45-46
47
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A SMALL END (1)
B LARGE END (1)
C DOOR END (1)
D UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G DOOR SHELF (3)
H DOOR UPRIGHT (1)
I LARGE SHELF (1)
J SMALL SHELF (1)
K BACK (1)
L LARGE DOOR (1)
M SMALL DOOR (1)
N LARGE ADJUSTABLE SHELF (2)
O ADJUSTABLE DOOR SHELF (3)
P SMALL ADJUSTABLE SHELF (2)
Q FRONT SKIRT (1)
R SIDE SKIRT (2)
S TOP MOLDING (1)
411965 www.sauder.com/servicesPage 2
Tape Measure
Part Identification

Now you know
our ABCs.
Part Identification
A
B
C
D
E
F
G
G
G
H
IJ
K
L M
N
N
O
O
O
P
P
Q
R
R
S
Hardware Identification
METAL BRACKET - 1
W
VTWIST-LOCK®FASTENER - 27
FRONT FOOT - 2
T
REAR FOOT - 2
U
411965www.sauder.com/services Page 3

åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
BLACK 7/8" MACHINE SCREW - 2
NN
ADJUSTABLE FOOT - 2
JJ
ADJUSTABLE GLIDE - 4
CC
SAFETY BRACKET - 1
Y
PROPEL NUT - 4
DD
SILVER 3/4" MACHINE SCREW - 2
OO
BLACK 9/16" LARGE HEAD SCREW - 19
RR
HOLE PLUG - 8
FF SMALL HOLE PLUG - 6 GG SHELF SNAP - 12
II
BLACK 1-7/8" FLAT HEAD SCREW - 9
MM
BLACK 9/16" WAFER HEAD SCREW - 4
QQ
HINGE - 4
LL
RUBBER SLEEVE - 16
BB
METAL PIN - 34
AA
SILVER 5/8" FLAT HEAD SCREW - 8
PP
BLACK 1/2" FLAT HEAD SCREW - 8
SS
DOOR STOP - 2
Z
NAIL - 72
TT
FOOT BASE - 2
KK
PULL - 2
X
EE SPRING HINGE - 3
STRIKE PLATE - 2
HH
411965 www.sauder.com/servicesPage 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (V) into the large holes in the ENDS (A and B), DOOR END
(C),TOP (E), DOOR SHELVES (G), LARGE SHELF (I), DOOR UPRIGHT (H), and SMALL SHELF (J).
å NOTE: Do not tighten the TWIST-LOCK® FASTENERS at this time.
LARGE DOOR ON LEFT LARGE DOOR ON RIGHT
A
B
27 used)
V
411965www.sauder.com/services Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å You have the option to assemble the Storage
Cabinet with the LARGE DOOR on the left or the
LARGE DOOR on the right.
å Follow steps 1-16 to assemble the LARGE DOOR
on the left.
å Follow steps 17-32 to assemble the LARGE
DOOR on the right.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID= 1126
to watch a video for the large door on the left.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID= 1125
to watch a video for the large door on the right.

å Fasten the LARGE END (B) to the TOP (E). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the LARGE SHELF (I) to the LARGE END (B).
Tighten two TWIST-LOCK® FASTENERS.
Step 2
B
E
I
Dowel end
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
LARGE DOOR ON LEFT
Surface with
TWIST-LOCK®
FASTENERS
411965 www.sauder.com/servicesPage 6
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Finished edge
Remember:
Righty tighty.
Lefty loosey.

å NOTE: Stand the UPRIGHT (D) in place to be sure you are
drilling through the correct holes in the TOP (E).
å There are four pre-drilled holes in the top surface of the
TOP (E). Finish drilling out two holes with your electric
drill and 1/4" drill bit.
å Fasten the UPRIGHT (D) to the TOP (E). Use two BLACK
1-7/8" FLAT HEAD SCREWS (MM).
å Fasten the UPRIGHT (D) to the LARGE SHELF (I). Tighten
two TWIST-LOCK® FASTENERS.
Step 3
LARGE DOOR ON LEFT
Find the correct pre-driled holes that
line up with the UPRIGHT (D) and drill
through the top surface of the TOP (E).
These four holes must be here.
E
I
D
411965www.sauder.com/services Page 7
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
MM
34-3/4"
34-3/4"
The measurement must be as shown. If it is
not, then flip the UPRIGHT (D) end for end.

å Fasten the TOP MOLDING (S) to the TOP (E). Tighten
three TWIST-LOCK® FASTENERS.
å Fasten the SMALL SHELF (J) to the UPRIGHT (D). Tighten
two TWIST-LOCK® FASTENERS.
Step 4
LARGE DOOR ON LEFT
Surface with
TWIST-LOCK®
FASTENERS
Finished edge
D
E
Angled edge
S
J
411965 www.sauder.com/servicesPage 8

å Fasten the SMALL END (A) to the TOP (E) and SMALL
SHELF (J). Tighten four TWIST-LOCK® FASTENERS.
Step 5
LARGE DOOR ON LEFT
Surface without
TWIST-LOCK®
FASTENERS
Edge with
TWIST-LOCK®
FASTENERS
A
E
J
411965www.sauder.com/services Page 9

å Finish drilling out the pre-drilled hole with your electric
drill and 1/4" drill bit to fasten the BOTTOM(F) to the
LARGE END (B) and UPRIGHT (D).
å Fasten the BOTTOM (F) to the ENDS (A and B) and
UPRIGHT (D). Use six BLACK 1-7/8" FLAT HEAD SCREWS (MM).
Step 6
LARGE DOOR ON LEFT
Rounded edge
Unfinished surface
Drill through these
pre-drilled holes.
A
B
D
F
411965 www.sauder.com/servicesPage 10
BLACK 1-7/8" FLAT HEAD SCREW
(6 used in this step)
MM