Sauder Briarbrook 429446 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-14
Français pg 15-17
Español pg 18-20
Lot # 573403 10/07/21
Purchased: __________________
Executive Table Desk
Briarbrook Collection | Model 429446
The original desktop.

Table of Contents
3
4
5-14
15-17
18-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Page 2 www.sauder.com/service 429446

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C MOLDING (2)
D BRACE (1)
E MODESTY PANEL (1)
F SUPPORT (3)
G TOP (1)
A
B
C
D
E
G
C
F
F
Page 3www.sauder.com/service429446

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
L-WRENCH - 1
2
PAD CARD - 1
1
2" HEX HEAD SCREW - 6
3413/16" HEX HEAD SCREW - 9
1/2" HEX HEAD SCREW - 26
5
HIDDEN WIRELESS Qi COMPATIBLE
CHARGER by EGGTRONIC - Item 425905
(sold separately)
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
Page 4 www.sauder.com/service 429446
CORD CLIP - 2
6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten the MOLDINGS (C) to the ENDS (A and B). Turn
sixteen 1/2" HEX HEAD SCREWS (5) a few turns using the
L-WRENCH (2). Do not completely tighten the SCREWS at
this time.
Do not completely tighten
screws till a later step.
WARNING
A
B
C
C
2
1/2" HEX HEAD SCREW
(16 used in this step)
5
Page 5www.sauder.com/service429446
The holes closer to this
edge should be here.

StepStep 2
å Fasten the BRACE (D) to the ENDS (A and B). Turn four
1/2" HEX HEAD SCREWS (5) a few turns using the
L-WRENCH (2). Do not completely tighten the SCREWS at
this time.
å Peel the PADS from the PAD CARD (1) and apply to the
bottom edge of the ENDS (A and B) as shown.
A
B
D
2
1/2" HEX HEAD SCREW
(4 used in this step)
5
1
Page 6 www.sauder.com/service 429446
Just think. The sooner
you do this, the sooner
you do something else.

Step
å Fasten the SUPPORTS (F) to the TOP (G) as shown. Turn
six 13/16" HEX HEAD SCREWS (4) a few turns using the
L-WRENCH (2). Do not completely tighten the SCREWS
at this time.
å Peel o the backing from the CORD CLIP (6) and apply the
CORD CLIP to the TOP (G) as shown.
Step 3
G
F
F
F
213/16" HEX HEAD SCREW
(6 used in this step)
4
Page 7www.sauder.com/service429446
6

Step
å Fasten the MOLDINGS (C) to the TOP (G). Turn six 2" HEX
HEAD SCREWS (3) a few turns using the L-WRENCH (2). Do
not completely tighten the SCREWS at this time.
å Fasten the ENDS (A and B) to the TOP (G). Turn six 1/2" HEX
HEAD SCREWS (5) a few turns using the L-WRENCH (2).
å Now, completely tighten all of the SCREWS in your unit.
Step 4
G
A
B
C
C
2
2" HEX HEAD SCREW
(6 used in this step)
3
1/2" HEX HEAD SCREW
(6 used in this step)
5
Page 8 www.sauder.com/service 429446

å This piece of furniture accommodates an optional Hidden Wireless Qi Compatible Charger by Eggtronic
(Item 425905) for charging your smartphone. Eliminate the clutter and inconvenience of a charging cable.
Charge your phone by simply setting it on top of your furniture.
å To purchase the Wireless Charger, scan this QR code.
(Or go to sauder.com)
å Qi Compatible Approved Smartphone
List
The embedded wireless charging system is designed for the following smartphones:
• Apple (iPhone 8 or newer)
• Samsung (Galaxy 6 or newer)
For a complete compatibility list, go to sauder.com.
å If you did not purchase the optional Hidden Wireless Qi Compatible Charger by Eggtronic, go to Step 9.
å If you purchased the optional Hidden Wireless Qi Compatible Charger by Eggtronic, go to the next step.
Step 5 Optional Hidden Wireless Qi Compatible Charger by Eggtronic (sold separately)
Wirelessly charge your
phone by setting it on
top of your furniture here.
Assembly Tools Required
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Tape Measure
Page 9www.sauder.com/service429446

Step
å Insert the HIDDEN WIRELESS Qi COMPATIBLE CHARGER by EGGTRONIC
into one of the large holes in the TOP (G).
å Use the two SCREWS included with the CHARGER to secure it into
the TOP (G).
å NOTE: There are no pre-drilled holes in the large holes in the TOP for the
CHARGER. The sides of the CHARGER will expand into the sides of the
large hole as you tighten the SCREWS.
WARNING
Please use the wireless charging port
correctly and safely. Improper use can
cause safety hazards, or damage to your
furniture or household items. Carefully
read the following safety information.
• AVOID dropping
• NEVER use in or near water
• DO NOT disassemble
• DO NOT expose to liquids
• DO NOT use with an extension cord
For safest and fastest charge, only use
original or certified cables.
G
Step 6 Optional Hidden Wireless Qi Compatible Charger by Eggtronic (sold separately)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
"Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device".
OR
"Changes or modifications not expressly approved by Sauder Woodworking Co. could void the user's authority to operate this device".
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Page 10 www.sauder.com/service 429446