Sauder Barrister Lane 414108 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-16
Français...............Pages 17-18
Espanol.............Páginas 19-20
Lot #: 350976 04 / 19 / 13
Date Purchased: ____________________
414108
Tall Bookcase
Barrister Lane Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-16
Français..............................17-18
Espanol...............................19-20
Safety .................................21-22
Warranty...................................23
Page 2 www.sauder.com/services 414108

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C UPRIGHT 1
D TOP 1
E BOTTOM 1
F SHELF 2
G PINNED SHELF 6
H BACK 1
I BASE 1
J LEFT BASE 1
K RIGHT BASE 1
L SHELF MOLDING 4
M FRONT MOLDING 1
N RIGHT MOLDING 1
O LEFT MOLDING 1
Page 3
www.sauder.com/services414108
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
F
G
G
G
G
G
L
L
L

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 414108
CARD SHEET - 1
38M
CORNER BRACKET - 2
31G
BLACK 1-7/8" FLAT HEAD SCREW - 5
2S
BLACK 1-1/4" FLAT HEAD SCREW - 4
7S
SAFETY BRACKET - 1
1G
NAIL - 77
1N
METAL PIN - 28
1R
METAL BRACKET - 8
4G
BLACK 9/16" LARGE HEAD SCREW - 29
1S
HIDDEN CAM - 32
1F CAM DOWEL - 24 2F
CAM COVER - 4
13P
CARD HOLDER - 8
35M
CAM SCREW - 8
8F
SILVER 3/8" MACHINE SCREW - 16
96S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push thirty-two HIDDEN CAMS (1F) into the ENDS (A and B), TOP (D), BOTTOM (E), and SHELVES (F and G). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except the ENDS (A and B) and TOP (D).
Page 5
www.sauder.com/services414108
Do not tighten the HIDDEN CAMS in this step.
(32 used)
(24 used)
Arrow
Arrow
1F
1F
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
Do not insert CAM
DOWELS into these parts.
A
BD
F
F
G
E
G
G
G
G
G
Arrow
1F
2F
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=730
to watch a video on how to assemble your unit.

2
2
S
t
e
p
Page 6 www.sauder.com/services 414108
Turn eight CAM SCREWS (8F) into the MOLDINGS (N and O).
Fasten the MOLDINGS (N and O) to the ENDS (A and B). Tighten four HIDDEN CAMS.
8F
8F
(8 used)
A
B
O
N
O
N
Surface with
HIDDEN
CAMS
Surface with
HIDDEN
CAMS
Angled edge
Angled edge
Finished edge
Finished edge
Surface with
CAM DOWELS

Fasten the UPRIGHT (C) to the TOP (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).
3
3
S
t
e
p
Page 7
www.sauder.com/services414108
D
C
Surface with
HIDDEN CAMS
These holes
must be here.
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
Finished edge
This large hole must
be positioned here.

Insert a METAL PIN (1R) into each SHELF (F).
Fasten the SHELVES (F) to the UPRIGHT (C). Tighten two HIDDEN CAMS.
NOTE: Be sure the METAL PINS (1R) in the SHELVES (F) insert into the holes in the UPRIGHT (C).
4
4
S
t
e
p
Page 8 www.sauder.com/services 414108
C
F
F
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
1R
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
Edge with
HIDDEN CAMS
Edge with
HIDDEN CAMS
1R

5
5
S
t
e
p
Page 9
www.sauder.com/services414108
Insert two METAL PINS (1R) into each PINNED SHELF (G).
Insert the METAL PINS (1R) in one end of the PINNED SHELVES (G) into the holes in the UPRIGHT (C).
C
G
Surface with
HIDDEN CAMS
G
Surface with
HIDDEN CAMS
G
Surface with
HIDDEN CAMS
G
Surface with
HIDDEN CAMS
G
Surface with
HIDDEN CAMS
G
Surface with
HIDDEN CAMS
1R
1R
(12 used)
Edge with
HIDDEN CAMS
Edge with
HIDDEN CAMS
Edge with
HIDDEN CAMS

Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).
6
6
S
t
e
p
Page 10 www.sauder.com/services 414108
C
E
Surface with
HIDDEN CAMS
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
These holes
must be here.