Sauder Palladia 411861 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot # 398136 10/25/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Technology Pier
Palladia Collection | Model 411861
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Spruce up. Charge up.

Table of Contents Assembly Tools Required
3
4-5
6-19
20-22
23-25
26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
411861 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 TOP (1)
D BOTTOM (1)
D36 RIGHT DRAWER SIDE (1)
D37 LEFT DRAWER SIDE (1)
D161 DRAWER BACK (1)
D719 DRAWER BOTTOM (1)
E SHELF (1)
F BACK (1)
G ADJUSTABLE SHELF (2)
H SKIRT (1)
I DRAWER FRONT (1)
J DRAWER BOX FRONT (1)
N TOP MOLDING (1)
O END MOLDING (2)
P SHELF MOLDING (1)
Q BOTTOM MOLDING (1)
R2 PLINTH (2)
Now you know
our ABCs.
411861www.sauder.com/services Page 3
A
B
C2
D
E
F
G
H
I
J
N
O
P
Q
R2
G
O
R2
D36
D37
D719
D161

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
TWIST-LOCK ®
FASTENER - 14
7F
ANGLE
BRACKET - 6
5G
TIE PLATE - 2
3G
METAL PIN - 8
1R RUBBER SLEEVE - 8 2R
NAIL - 40
1N
1F HIDDEN CAM - 4 CAM SCREW - 4 8F
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1
DRAWER FRONT
BRACKET - 1
9G
METAL
BRACKET - 4
4G
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M SAFETY DRYWALL
ANCHOR - 1
61M
WASHER - 1
13M
KNOB - 1
33K
411861 www.sauder.com/servicesPage 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/4" FLAT HEAD SCREW - 3
7S
SILVER 1-1/4" MACHINE SCREW - 1
35S
17S BLACK 7/8" LARGE HEAD SCREW - 4
1S BLACK 9/16" LARGE HEAD SCREW - 25
BROWN 7/16" LARGE HEAD SCREW - 4
6S
GOLD 5/16" FLAT HEAD SCREW - 8
3S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
411861www.sauder.com/services Page 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the ENDS (A and B).
å Repeat this step for the BOTTOM (D) and SHELF (E).
411861 www.sauder.com/servicesPage 6
7F
7F
7F
A
B
(14 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1735
to watch a video on how to assemble your unit.

Step
411861www.sauder.com/services Page 7
Step 2
å Push four HIDDEN CAMS (1F) into the BOTTOM (D)
and SHELF (E).
D
E
1F (4 used)
Arrow
Arrow
Hole
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.

Step
å Turn four CAM SCREWS (8F) into the MOLDINGS (P and Q).
Step 3
411861 www.sauder.com/servicesPage 8
PQ
8F
(4 used)
Remember:
Righty tighty.
Lefty loosey.

Step
411861www.sauder.com/services Page 9
Step 4
å Fasten the CABINET RIGHT (35GA) and CABINET LEFT (35GB)
to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
å Fasten six ANGLE BRACKETS (5G) to the ENDS (A and B). Use
six BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are even with
the edges of the ENDS.
A
B
1
2
3
3
2
1
5G
5G
Edge with
TWIST-LOCK®
FASTENER
Roller end
Roller end
Edge with
TWIST-LOCK®
FASTENER
BLACK 9/16" LARGE HEAD SCREW
(6 used for the ANGLE BRACKETS)
1S
GOLD 5/16" FLAT HEAD SCREW
(4 used for the CABINET RAILS)
3S

Step
å Fasten the LEFT END (B) to the TOP (C2). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the BOTTOM (D) and SHELF (E) to the LEFT
END (B). Tighten four TWIST-LOCK® FASTENERS.
Step 5
411861 www.sauder.com/servicesPage 10
BC2
E
D
Edge with
TWIST-LOCK®
FASTENER
Edge with HIDDEN CAMS.
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
Rounded edge
Surface with holes
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
This hole must be here.