Sauder Worksense 427836 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Sauder.com
Share your journey!
How can we help you? To reach our customer service, visit sauder.com/oceservice to chat with a
live rep or email us.
Prefer the phone? Give us a rin at
877-996-7539 .
Our award-winnin team is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays).
Lot # 560971 03/02/21
Purchased: __________________
Enlish p 1-34
Français p 35-39
Español p 40-44
File Credenza
Prime Oak finish | Model 427836
Mason Peak COLLECTION

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
3
4-5
8
6-34
35-39
40-44
45-46
47
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
427836 www.sauder.com/oceservicePae 2
Nail Holder (provided)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D RIGHT TOP MOLDING (1)
D14 RIGHT DRAWER SIDE (1)
D15 LEFT DRAWER SIDE (1)
D552 DRAWER BACK (1)
D985 DRAWER BOTTOM (1)
E LEFT TOP MOLDING (1)
F FIXED SHELF MOLDING (1)
G FRONT TOP MOLDING (1)
H UPRIGHT (1)
J UPRIGHT MOLDING (1)
K FIXED SHELF (1)
L ADJUSTABLE SHELF (1)
M DRAWER FRONT (1)
M67
DRAWER BRACE (1)
(Hidden part usin recycled
material. Color may vary.)
N BOTTOM (1)
O FRONT SKIRT (1)
P BACK SKIRT (1)
Q RIGHT SKIRT (1)
R LEFT SKIRT (1)
S BACK (1)
T DOOR (1)
427836www.sauder.com/oceservice Pae 3
A
B
CD
E
F
G
H
J
K
L
M
N
O
R
S
T
Q
PD14
D15
D552
D985
M67

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FILE GLIDE - 2
4B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 2
35MA EXTENSION SLIDE - 2 35MC 10A SLIDE CAM - 2
191K PULL - 3MAGNETIC CATCH - 1
2I STRIKE PLATE - 1 6I NAIL - 20 1N
FILE ROD - 2
9B FILE BAR - 2
14B
SMALL FILE
BRACKET - 1
11B HIDDEN CAM - 1 1F
31G CORNER BRACKET - 4
METAL BRACKET - 6
4G LARGE FILE
BRACKET - 1
57G 42H HINGE - 2
MOLDING
CONNECTOR - 2
17F
CAM SCREW - 1
8F WOOD DOWEL - 4 15F 37F TWIST-LOCK®FASTENER - 10
427836 www.sauder.com/oceservicePae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BROWN 7/16" LARGE HEAD SCREW - 4
6S BLACK 1/2" FLAT HEAD SCREW - 1 11S
BLACK 7/8" MACHINE SCREW - 6
37S30S BLACK 1-9/16" FLAT HEAD SCREW - 5
GROMMET CAP - 1
1P GROMMET - 1 10P SHELF REST - 4
10R
105P TWIST-LOCK®
FASTENER COVER - 9
BLACK 9/16" LARGE HEAD SCREW - 44
1S 3S GOLD 5/16" FLAT HEAD SCREW - 8
BLACK 1-15/16" FLAT HEAD SCREW - 6
113S SILVER 1-5/8" FLAT HEAD SCREW - 7
152S
427836www.sauder.com/oceservice Pae 5

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0
427836 www.sauder.com/oceservicePae 6
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Tap two MOLDING CONNECTORS (17F) into the notches
in the MOLDINGS (D, E, and G).
D
E
G
Flat end
17F
Flat end
17F
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.
Just think. The sooner
you do this, the sooner
you do somethin else.

Step 2
427836www.sauder.com/oceservice Pae 7
å Fasten the MOLDINGS (D, E, and G) to the TOP (C). Use
seven SILVER 1-5/8" FLAT HEAD SCREWS (152S).
å NOTE: Start each SCREW a few turns before completely
tihtenin any of them.
å NOTE: Do not overtihten the SCREWS into the TOP.
Surface with holes
D
G
E
C
SILVER 1-5/8" FLAT HEAD SCREW
(7 used in this step)
152S

Hardware Usage Guide
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
1. Insert the dowel end of the FASTENER into the
hole of the adjoinin part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoinin
part while lockin the FASTENER.
2. Tihten the FASTENER with a Phillips
screwdriver as tiht as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the lare hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
427836 www.sauder.com/oceservicePae 8

Step 3
427836www.sauder.com/oceservice Pae 9
å Push four SAUDER TWIST-LOCK® FASTENERS (37F) into
the lare holes in the LEFT END (B) and UPRIGHT (H).
å Insert two WOOD DOWELS (15F) into the LEFT END (B).
B
H
2
37F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
15F
37F
Meet Part (B). This component has
been enineered to be lihter, stroner,
faster… well ok. Not technically faster.
But definitely makes for a sturdier File
Credenza that’s easier to assemble and
friendlier to the environment.

Step 4
427836 www.sauder.com/oceservicePae 10
å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the upper
diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (35MA) to the LEFT END (B) and UPRIGHT (H). Use four GOLD 5/16"
FLAT HEAD SCREWS (3S) throuh holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then,
slide the inner cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in
the END or UPRIGHT. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWER.
B
H
Open end
Push the black lever in and pull the SLIDE from the RAIL.
35MA35MC
3
2
1
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(4 used for the RAILS)
3S
7
Open end
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS

Step 5
427836www.sauder.com/oceservice Pae 11
å Fasten the LEFT END (B) to the LEFT TOP MOLDING (E).
Tihten two TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END
insert into the LEFT TOP MOLDING.
C
E
B
Surface with
TWIST-LOCK®
FASTENERS
2

Step 6
427836 www.sauder.com/oceservicePae 12
å Push four SAUDER TWIST-LOCK® FASTENERS (37F) into the
lare holes in the FIXED SHELF (K).
å Fasten the FIXED SHELF (K) to the LEFT END (B). Tihten two
TWIST-LOCK® FASTENERS.
2
37F
37F
K
K
B
Surface with TWIST-LOCK® FASTENERS
Notched ede

Step 7
427836www.sauder.com/oceservice Pae 13
å Slide the FIXED SHELF MOLDING* (F) onto the notched
ede of the FIXED SHELF (K).
å *U.S. Patent No. 5,499,886
Slide the FIXED SHELF MOLDING (F)
onto the notched ede.
These surfaces should be even.
The roove
is closer to
this ede.
Notched ede
F
K

Step 8
427836 www.sauder.com/oceservicePae 14
å Slide the UPRIGHT MOLDING* (J) onto the notched ede
of the UPRIGHT (H).
å *U.S. Patent No. 5,499,886
Slide the UPRIGHT MOLDING (J) onto the notched ede.
The roove
is closer to
this ede.
Notched ede
These surfaces
should be even.
H
J

Step 9
427836www.sauder.com/oceservice Pae 15
å Fasten the UPRIGHT (H) to the TOP (C) and FIXED
SHELF (K). Tihten four TWIST-LOCK® FASTENERS.
H
K
Surface with TWIST-LOCK® FASTENERS
C
2

Step 10
427836 www.sauder.com/oceservicePae 16
å Push two SAUDER TWIST-LOCK® FASTENERS (37F) into the
lare holes in the RIGHT END (A).
å Insert two WOOD DOWELS (15F) into the RIGHT END (A).
A
37F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
15F
Part (A). Another
sturdier, easier,
friendlier component!
2

Step 11
427836www.sauder.com/oceservice Pae 17
å Fasten the RIGHT END (A) to the RIGHT TOP MOLDING (D).
Tihten two TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
insert into the RIGHT TOP MOLDING.
A
D
Surface without TWIST-LOCK® FASTENERS
Side Step: Make
nachos. (Optional, but
recommended.)
2

Step 12
427836 www.sauder.com/oceservicePae 18
å Insert the GROMMET (10P) and GROMMET CAP (1P) into
the lare hole in the BOTTOM (N).
N
1P
10P
Surface with fewer holes

Step 13
427836www.sauder.com/oceservice Pae 19
å Fasten the BOTTOM (N) to ENDS (A and B) and UPRIGHT (H).
Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: Start each SCREW a few turns before completely
tihtenin any of them.
NA
B
H
BLACK 1-15/16" FLAT HEAD SCREW
(6 used in this step)
113S
Surface with more holes
The GROMMET on the other
surface is closer to this ede.

Step 14
427836 www.sauder.com/oceservicePae 20
å Fasten six METAL BRACKETS (4G) to the SKIRTS (O, P, Q, and R). Use
six BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes of the SKIRTS.
P
O
R
Q
4G
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S