Sauder International Lux 430877 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-26
Français p 27-30
Español p 31-34
Lot # 564095 03/24/21
Purchased: __________________
Desk
International Lux Collection | Model 430877
Sit and surf.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-26
27-30
31-34
35-36
37
Pae 2 www.sauder.com/service 430877

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT FRAME (1)
B CENTER FRAME (1)
C RIGHT FRAME (1)
D TOP (1)
E LEFT END (1)
F UPRIGHT (1)
G RIGHT END (1)
H SHELF (2)
J BOTTOM (1)
K RIGHT BACK (1)
L LEFT BACK (1)
M EXTENSION BLOCK (1)
N DRAWER FRONT (1)
O LEFT DRAWER SIDE (1)
P RIGHT DRAWER SIDE (1)
Q DRAWER BACK (1)
R DRAWER BOTTOM (1)
S DRAWER BRACE (1)
T FILE DRAWER FRONT (1)
U FILE LEFT DRAWER SIDE (1)
V FILE RIGHT DRAWER SIDE (1)
W FILE DRAWER BACK (1)
X FILE DRAWER BOTTOM (1)
Y LONG BRACE (1)
Z SHORT BRACE (2)
A
B
C
D
E
F
G
H
J
K
LM
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Z
H
Pae 3www.sauder.com/service430877

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 12
21-3/16" HEX HEAD SCREW - 6
3
CAM SCREW - 12
1
1/2" HEX HEAD SCREW - 2
6
1-3/8" HEX HEAD SCREW - 6
4METAL PIN - 6
5
7/16" PAN HEAD SCREW - 24
81/2" FLAT HEAD SCREW - 18 9
1-3/16" FLAT HEAD SCREW - 14
7
METAL BRACKET - 8
11 PULL - 2
12
3/4" FLAT HEAD SCREW - 2
10
16 RIGHT EXTENSION
RAIL and SLIDE - 1
15 LEFT EXTENSION
RAIL and SLIDE - 1
14 RIGHT FILE GLIDE - 1 13 LEFT FILE GLIDE - 1
L-WRENCH - 1
19 APPLIQUE CARD - 2 20
18 WIDE EXTENSION
SLIDE - 2
17 WIDE EXTENSION
RAIL - 2
Pae 4 www.sauder.com/service 430877

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Turn twelve CAM SCREWS (1) into the TOP (D), DRAWER
FRONT (N), and FILE DRAWER FRONT (T).
Pae 5www.sauder.com/service430877
1(12 used)
1
D
N
T

å Push twelve HIDDEN CAMS (2) into the LEFT BACK (L),
DRAWER SIDES (O and P), DRAWER BRACE (S), and FILE
DRAWER SIDES (U and V).
Step 2
Pae 6 www.sauder.com/service 430877
L
P
O
S
U
V
Arrow
2
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
1
(12 used)

å NOTE: Position the parts exactly as shown.
å Fasten the RIGHT EXTENSION RAIL and SLIDE (16) to the EXTENSION BLOCK (M) and UPRIGHT (F). Use two
3/4" FLAT HEAD SCREWS (10) throuh the RIGHT EXTENSION RAIL and SLIDE, throuh the EXTENSION BLOCK,
and into the UPRIGHT.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the UPRIGHT. Turn a SCREW
into this hole.
Step 3
Pae 7www.sauder.com/service430877
F
Finished ede
Surface with fewer holes
3/4" FLAT HEAD SCREW
(2 used in this step)
16
M
Closed end
Finished surface
6th hole
16
M
Bracket must
be positioned
as shown
16
Use these holes
16
10

Step 4
Pae 8 www.sauder.com/service 430877
E
å NOTE: Position the parts exactly as shown.
å Fasten the LEFT EXTENSION RAIL and SLIDE (15) to the LEFT
END (E). Use two 1/2" FLAT HEAD SCREWS (9).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole
shown in the enlared diaram. Then, slide the inner cartride
of the EXTENSION RAIL in to find the other hole that lines up
with the hole in the END. Turn a SCREW into this hole.
1/2" FLAT HEAD SCREW
(2 used in this step)
9
Closed end
6th hole
Finished ede
15
Bracket must
be positioned
as shown
15
E
15
Some assembly
(and snacks) required.
Use these holes
15

å Flip the UPRIGHT (F) over.
å Separate the WIDE EXTENSION SLIDES (18) from the WIDE EXTENSION RAILS (17) as shown in the upper diaram
below. Be prepared, the parts are reasy.
å Fasten the WIDE EXTENSION RAILS (17) to the UPRIGHT (F) and RIGHT END (G). Use four 1/2" FLAT
HEAD SCREWS (9).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the UPRIGHT and RIGHT END.
Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Step 5
Pae 9www.sauder.com/service430877
F G
Finished ede
17 17
Slide the black lever up and pull the SLIDE from the RAIL.
7
Open end
Open end
1/2" FLAT HEAD SCREW
(4 used in this step)
9
Use this hole Use this hole
Use these holes
17 18
17

å Fasten eiht METAL BRACKETS (11) to the UPRIGHT (F)
and RIGHT END (G) exactly as shown. Use eiht 7/16"
PAN HEAD SCREWS (8).
Step 6
Pae 10 www.sauder.com/service 430877
F
G
11
11
Finished
ede
Finished
ede
7/16" PAN HEAD SCREW
(8 used in this step)
8