Sauder Costa Credenza 419959 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 394437 09/22/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Credenza
Costa Collection | Model 419959
Sit and surf.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4
5-28
29-32
33-36
37-38
39
Hammer
Not actual size
Now you know
our ABCs.
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C END MOLDING (2)
D PRINTER SHELF (1)
E SHORT BOTTOM MOLDING (2)
F RIGHT BOTTOM (1)
G BOTTOM (1)
H RIGHT FRONT LEG (2)
I BOTTOM MOLDING (1)
J ADJUSTABLE SHELF (2)
K PRINTER SHELF MOLDING (1)
L RIGHT UPRIGHT (1)
M LEFT UPRIGHT (1)
N CENTER BACK (1)
O LEFT REAR LEG (1)
P LEFT FRONT LEG (2)
Q LEFT CENTER LEG (1)
R LEFT BOTTOM (1)
S RIGHT REAR LEG (1)
T RIGHT CENTER LEG (1)
U BACK (2)
V TOP (1)
W LEFT DOOR (1)
X RIGHT DOOR (1)
419959 www.sauder.com/servicesPage 2
Nail Holder (provided)
Tape Measure
Electric drill with 3/16" bit
(ONLY in indicated step)

Part Identification
419959www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
U
J
E
H
P
C

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419959 www.sauder.com/servicesPage 4
BB LEFT DRAWER
SLIDE - 1
RIGHT CABINET
RAIL - 1
YLEFT CABINET
RAIL - 1
ZRIGHT DRAWER
SLIDE - 1
AA
BLACK 1-1/8" MACHINE SCREW - 2
21S
GROMMET CAP - 1
1P
18S BROWN 1" FLAT HEAD SCREW - 4
12F TWIST-LOCK®
FASTENER - 20
CORD CLIP - 1
4P
3S GOLD 5/16" FLAT HEAD SCREW - 4
METAL PIN - 8
1R
BLACK 1/2" FLAT HEAD SCREW - 8
11S
BLACK 9/16" FLAT HEAD SCREW - 4
32S
CAM SCREW - 27
8F
DOOR STOP - 2
4I
WOOD DOWEL - 16
15F
GROMMET - 1
10P
NAIL - 52
1N
HIDDEN CAM - 27
1F
GLUE - 1
54M
RUBBER SLEEVE - 8
2R
14H HINGE - 4 KNOB SET - 2
136K
METAL BRACKET - 1
4G
BLACK 9/16" LARGE HEAD SCREW - 1
1S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
419959www.sauder.com/services Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(20 used)
12F
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (12F) into the large holes in the ENDS (A
and B). Repeat this step for the BOTTOMS (F, G, and R)
and UPRIGHTS (L and M).
A
B
STOP
If you purchased
the 419958 Hutch,
assemble that unit
fi r s t .

Step 2
419959 www.sauder.com/servicesPage 6
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
å Push twenty-seven HIDDEN CAMS (1F) into the ENDS (A
and B), PRINTER SHELF (D), and UPRIGHTS (L and M).
1F
Arrow
A
B
L
M
D
(27 used)
Some assembly
(and snacks) required.

Step 3
419959www.sauder.com/services Page 7
8F
å Turn twenty-seven CAM SCREWS (8F) into the PRINTER
SHELF MOLDING (K) and LEGS (H, O, P, Q, S, and T).
H
K
O
P
Q
S
T
H
P
(27 used)

Step 4
419959 www.sauder.com/servicesPage 8
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å NOTE: Do not overtighten the SCREWS.
å Slide the END MOLDINGS (C) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again. The MOLDINGS should be
even on both edges of the ENDS.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
A
B
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
C
C
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Shoulder

Step 5
419959www.sauder.com/services Page 9
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
å First, fill the exact two holes shown in the RIGHT END (A) 1/4 to 1/2 full with
GLUE (54M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away
the excess GLUE.
å NOTE: Be sure to position the parts exactly as shown.
å Now, fill the holes in the LEGS (H and S) 1/4 to 1/2 full with GLUE (54M).
å Fasten the LEGS (H and S) to the RIGHT END (A). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into the LEGS.
Wipe away the excess GLUE.
54M
15F
A
H
These surfaces
should be even.
Edge with
TWIST-LOCK®
FASTENERS
1
2
Edge without hole
Surface with
HIDDEN CAMS
S
Edge without hole
These surfaces
should be even.

Step 6
419959 www.sauder.com/servicesPage 10
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
15F
B
O
These surfaces
should be even.
Edge with
TWIST-LOCK®
FASTENERS
Edge with hole
Surface with
HIDDEN CAMS
P
These surfaces
should be even.
å First, fill the exact two holes shown in the LEFT END (B) 1/4 to 1/2 full with
GLUE (54M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away
the excess GLUE.
å NOTE: Be sure to position the parts exactly as shown.
å Now, fill the holes in the LEGS (O and P) 1/4 to 1/2 full with GLUE (54M).
å Fasten the LEGS (O and P) to the LEFT END (B). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END insert into the LEGS. Wipe
away the excess GLUE.
Edge with hole
15F