Sauder Sewing/Craft Cart User manual

Sewing/Craft Cart
We'll have you in
stitches.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
3
4
5-18
19-21
22-24
25-26
27
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 UPRIGHT (1)
D2 TOP (1)
E FLIP-UP TOP (1)
F BOTTOM (1)
G2 MODESTY PANEL (1)
H2 SHELF (1)
I BACK (1)
J CENTER DOOR (1)
K RIGHT DOOR (1)
L LEFT DOOR (1)
M ADJUSTABLE SHELF (2)
A
B
C2
D2
E
F
G2
H2
I
J
K
L
M
M
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
TIGHT HINGE- 2
2H LOOSE HINGE- 2 3H
Page 4
TRAY - 2
2D TRAY DIVIDER - 8 3D
LOCKING CASTER - 2
2CL CASTER - 4 2CN
BLACK 1-1/8" PAN HEAD SCREW - 2
9S
GOLD 1" MACHINE SCREW - 3
50S
BLACK 9/16" LARGE HEAD SCREW - 40
1S
18S BROWN 1" FLAT HEAD SCREW - 2
12P CAM COVER - 4
HINGE - 5
16H
METAL PIN - 8
1R
SLIDE CATCH - 1
6J
MAGNETIC CATCH - 2
5I
BLACK 1/2" FLAT HEAD SCREW - 2
11S
NAIL - 13
1N
HIDDEN CAM - 14
1F CAM DOWEL - 14 2F
RUBBER SLEEVE - 8
2R
17E CASTER BRACKET - 6
KNOB - 3
19K
STRIKE PLATE - 2
6I
BLACK 1-15/16" FLAT HEAD SCREW - 4
113S

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C2), BOTTOM (F), MODESTY PANEL (G2), and
SHELF (H2). Then, insert the metal end of the CAM DOWEL (2F)
into each HIDDEN CAM.
Do not tighten the HIDDEN CAMS in this step.
(14 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Page 5
A
B
C2
F
G2
H2

å Fasten the RIGHT END (A) to the TOP (D2). Tighten two
HIDDEN CAMS.
Step 2
Page 6
Surface with
HIDDEN CAMS
A
D2
Finished edge
Rounded edge
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Surface with holes

å Fasten the BOTTOM (F) to the RIGHT END (A). Tighten
two HIDDEN CAMS.
Step 3
Page 7
Finished edge A
F
Arrow
Minimum
190 degrees
Maximum
210 degrees
Surface with
HIDDEN CAMS

Step 4
å Fasten the UPRIGHT (C2) to the TOP (D2) and BOTTOM (F).
Tighten four HIDDEN CAMS.
å Fasten two MAGNETIC CATCHES (5I) to the UPRIGHT (C2).
Use two BLACK 1-1/8" PAN HEAD SCREWS (9S).
å Fasten the MODESTY PANEL (G2) to the UPRIGHT (C2).
Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S).
Page 8
C2
D2
F
G2
5I
BLACK 1-1/8" PAN HEAD SCREW
(2 used for the MAGNETIC CATCHES)
9S
Surface with HIDDEN CAMS
Arrow
Minimum
190 degrees
Maximum
210 degrees
Surface without
HIDDEN CAMS
BLACK 1-15/16" FLAT HEAD SCREW
(2 used for the MODESTY PANEL)
113S

å Fasten the SHELF (H2) to the UPRIGHT (C2). Use two
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å Fasten the LEFT END (B) to the TOP (D2), MODESTY
PANEL (G2), and SHELF (H2). Tighten six HIDDEN CAMS.
Step 5
Page 9
Arrow
Minimum
190 degrees
Maximum
210 degrees
B
C2
D2
G2
H2
Surface with
HIDDEN CAMS
BLACK 1-15/16" FLAT HEAD SCREW
(2 used for the SHELF)
113S

å Carefully turn your unit over onto its front edges. Lay the
BACK (I) over your unit.
å Make equal margins along three edges of the BACK (I). Push
on the bottom edges of the RIGHT END and UPRIGHT if
needed to make it "square".
å NOTE: The BACK should be against the bottom surface of
the TOP.
å Fasten the BACK (I) to your unit using the NAILS (1N).
Step 6
Page 10
I
Edge without holes
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(13 used in this step)
1N
Finished surface