Sauder Entertainment Credenza User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-24
Français p 23-25
Español p 26-28
Lot # 362999 06/25/14
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Entertaining what
entertains you.
Entertainment Credenza
Camarin Collection | 414802

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Skip the power trip.
This time.
3
4
5-22
23-25
26-28
29-30
31
Use of a TV that is too heavy or lare is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too lare for the available space miht be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weiht of your TV. Compare it to the diaram below – before you begin assembly!
• This Sauder unit is desined for use with televisions weihin less than 95 pounds. Never use with a TV that weihs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diaram.
• Never place the front ede of the TV past the front ede of the TV support shelf (or stop moldin – if equipped)
• Never allow the sides of the TV to extend past the side edes of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warnin label as instructed in the last assembly step. The label provides important safety related information.
47-1/4" 19-1/2"
26-1/2"
414802 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
D16 RIGHT DRAWER SIDE (2)
D17 LEFT DRAWER SIDE (2)
D73 DRAWER BACK (2)
D720 DRAWER BOTTOM (2)
E UPRIGHT (1)
F TOP (1)
G BOTTOM (1)
H SHELF (1)
I BACK (1)
J ADJUSTABLE SHELF (1)
K FRONT SKIRT (1)
L SIDE SKIRT (2)
M DRAWER FRONT (2)
RLEFT FRONT/RIGHT REAR
FOOT (2)
SRIGHT FRONT/LEFT REAR
FOOT (2)
T CENTER FOOT (2)
A
B
C
D
E
F
G
H
I
J
K
L
L
M
M
R
R
S
ST
D16
D16
D17
D17
D73
D73
D720
D720
414802www.sauder.com/services Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
METAL BRACKET - 3
DD
GOLD 1" MACHINE SCREW - 2
MM BLACK 9/16" LARGE HEAD SCREW - 35
NN
CAM COVER - 4
GG
OO GOLD 5/16" FLAT HEAD SCREW - 16
METAL PIN - 10
HH
FF SLIDE CAM - 4
BLACK 1-15/16" FLAT HEAD SCREW - 10
KK
NAIL - 48
PP
LL BLACK 1-9/16" FLAT HEAD SCREW - 8
HIDDEN CAM - 10
YCAM DOWEL - 10 Z
KNOB - 2
EE
AA CORNER CAP - 1 BB FOOT BRACKET - 1
35GA CABINET RIGHT - 2 35GB CABINET LEFT - 2 35GC DRAWER RIGHT - 2 35GD DRAWER LEFT - 2
CC CORNER BRACKET - 4
RUBBER SLEEVE - 4
II
(Refer to step __ for proper location and application)
WARNING LABEL - 1
JJ
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227
414802 www.sauder.com/servicesPae 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
Arrow
Y
Z
(10 used)
(10 used)
Arrow
Y
Z
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push ten HIDDEN CAMS (Y) into the ENDS (A and B),
RIGHT UPRIGHT (C), and SHELF (H). Then, insert a CAM
DOWEL (Z) into each HIDDEN CAM.
A
B
C
H
414802www.sauder.com/services Pae 5

å Fasten the CABINET RIGHTS (35GA) and CABINET
LEFTS (35GB) to the RIGHT END (A) and RIGHT
UPRIGHT (C). Use eiht GOLD 516" FLAT HEAD
SCREWS (OO) throuh holes #1 and #3.
Step 2
1
2
3
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
OO
1
2
3
1
2
3
Roller end
Roller end
Finished ede
Rounded ede
414802 www.sauder.com/servicesPae 6
Remember:
Rihty tihty.
Lefty loosey.
A
C

å Fasten the LEFT END (B) to the TOP (F). Tihten two
HIDDEN CAMS.
å Insert two METAL PINS (HH) into the UPRIGHT (E).
å Insert the METAL PINS in the end of the UPRIGHT (E) into
the holes in the TOP (F).
Step 3
Surface
with holes
B
E
F
HH
Finished ede
Rounded ede
Rounded ede
Surface with
HIDDEN CAMS
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
414802www.sauder.com/services Pae 7

å Fasten the SHELF (H) to the LEFT END (B). Tihten two
HIDDEN CAMS.
å Fasten the SHELF (H) to the UPRIGHT (E). Use two
BLACK 11516" FLAT HEAD SCREWS (KK).
Step 4
B
E
H
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with
HIDDEN CAMS
KK
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
414802 www.sauder.com/servicesPae 8
Finished ede

å Fasten the RIGHT UPRIGHT (C) to the SHELF (H).
Tihten two HIDDEN CAMS.
å Insert two METAL PINS (HH) into the LEFT UPRIGHT (D).
å Insert the two METAL PINS (HH) in the end of the LEFT
UPRIGHT (D) into the holes in the SHELF (H).
Step 5
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with
HIDDEN CAMS
Finished ede
HH
C
D
H
Surface
without holes
414802www.sauder.com/services Pae 9

å Fasten the RIGHT END (A) to the TOP (F) and SHELF (H).
Tihten four HIDDEN CAMS.
Step 6
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with
HIDDEN CAMS
Rounded ede
A
F
H
414802 www.sauder.com/servicesPae 10