Sauder Hammond 428248 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 549493 06/18/20
Purchased: __________________
Hutch
Hammond Collection | Model 428248
Knick-knack
paddywhack,
give your stu a home.

Table of Contents Assembly Tools Required
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
3
4
5-24
25-28
29-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Page 2 www.sauder.com/service 428248
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3www.sauder.com/service428248
A TOP (1)
B LEFT END (1)
C RIGHT END (1)
D SHELF (1)
E UPRIGHT (2)
F CENTER LARGE BACK (1)
G LOWER BACK (2)
H SMALL ADJUSTABLE SHELF (2)
J LONG BRACE (1)
K LARGE ADJUSTABLE SHELF (1)
L DOOR (2)
M OUTER SMALL BACK (2)
N CENTER BRACE (1)
A
B
C
D
E
E
F
G
G
H
H
J
K
L
L
M
M
N

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/service 428248
BLACK 1/2" PAN HEAD SCREW - 34
16
BLACK 1" FLAT HEAD SCREW - 8
13
BLACK 1" MACHINE SCREW - 2
12
WOOD DOWEL - 18
3
HIDDEN CAM - 22
1CAM SCREW - 22 2METAL PIN - 12 4
BLACK 5/8" FLAT HEAD SCREW - 10
15
SMALL BLACK 5/8" FLAT HEAD SCREW - 24
14
METAL L-BRACKET - 2
6
METAL Z-BRACKET - 2
5HINGE - 4
7APPLIQUE CARD - 3 8
9BUMPER CARD - 1 KNOB SET - 2 10 FURNITURE TIPPING
RESTRAINT KIT - 1
96

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
Page 5www.sauder.com/service428248
1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn twenty-two CAM SCREWS (2) into the exact holes
shown in the TOP (A), ENDS (B and C), SHELF (D), and
LONG BRACE (J).
A
F
L
I
P
O
V
E
R
B
C
J
D
D
2(22 used)
Meet Part (A). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
Hutch that’s easier to assemble and
friendlier to the environment.
Part (D). Another
sturdier, easier,
friendlier component!

Step 2
Page 6 www.sauder.com/service 428248
å Insert eighteen WOOD DOWELS (3) into the short edges
of the ENDS (B and C), UPRIGHTS (E), SHELF (D), and
LONG BRACE (J).
3
3
(18 used)
B
C
E
E
D
J
3
Just think. The sooner
you do this, the sooner
you do something else.

Step 3
Page 7www.sauder.com/service428248
1
B
C
E
E
D
J
å Push twenty-two HIDDEN CAMS (1) into the ENDS (B
and C), SHELF (D), UPRIGHTS (E), LONG BRACE (J), and
CENTER BRACE (N).
1
Arrow
1
Arrow
1
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
1
Arrow
1
(22 used)
N
Arrow

Step 4
Page 8 www.sauder.com/service 428248
1
å Fasten the CENTER BRACE (N) to the SHELF (D). Tighten
two HIDDEN CAMS.
å Fasten the LONG BRACE (J) to the CENTER BRACE (N).
Tighten two HIDDEN CAMS.
1
2
Surface with HIDDEN CAMS
Surface
with
HIDDEN
CAMS
Surface with
HIDDEN CAMS
J
N
D
Long edge
with holes

Step 5
Page 9www.sauder.com/service428248
1
å This step will require someone's help.
å Turn your unit onto its front edge.
å Fasten the ENDS (B and C) to the SHELF (D) and LONG
BRACE (J). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SHELF and
LONG BRACE insert into the holes in the ENDS.
å Fasten the UPRIGHTS (E) to the SHELF (D). Tighten four
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHTS
insert into the holes in the SHELF.
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
J
N
D
B
C
E
E
Unfinished edge
A second person will need to
support the LONG BRACE as
you fasten the ENDS (B and C).

Step 6
Page 10 www.sauder.com/service 428248
1
å Fasten the TOP (A) to the ENDS (B and C) and
UPRIGHTS (E). Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHTS
and ENDS insert into the holes in the TOP.
A
B
C
E
E
Curved edge

Step 7
Page 11www.sauder.com/service428248
å Slide the OUTER SMALL BACKS (M) into the grooves of the ENDS (B
and C) and TOP (A). Be sure to position them exactly as shown.
å Lay the CENTER LARGE BACK (F) over the center opening of your
unit, pushing it into the groove of the TOP (A).
å Fasten the BACKS (F and M) to the UPRIGHTS (E). Turn four BLACK
1/2" PAN HEAD SCREWS (16) into the notches of the BACKS.
å Finish fastening the BACKS (F and M) to the SHELF (D). Use eight
additional BLACK 1/2" PAN HEAD SCREWS (16).
å Slide the LOWER BACKS (G) into the grooves of the ENDS (B and C).
A
B
G
GF
M
M
G
The BACKS will have notches
here for the SCREWS.
BLACK 1/2" PAN HEAD SCREW
(12 used in this step)
16
C
This edge of the BACK
will not have holes.
This edge of the BACK
will not have holes.

Step 8
Page 12 www.sauder.com/service 428248
å Fasten the LOWER BACKS (G) to the SHELF (D), LONG
BRACE (J), and CENTER BRACE (N). Use twenty-two
BLACK 1/2" PAN HEAD SCREWS (16).
G
G
BLACK 1/2" PAN HEAD SCREW
(22 used in this step)
16
J
This edge of the BACK
will not have holes.
Now might be a
good time to refresh
your drink.
This edge of the BACK
will not have holes.

Step 9
Page 13www.sauder.com/service428248
å Fasten two HINGES (7) to a DOOR (L). Use four SMALL
BLACK 5/8" FLAT HEAD SCREWS (14).
å NOTE: The SMALL BLACK 5/8" FLAT HEAD SCREW (14) is
slightly smaller than the BLACK 5/8" FLAT HEAD SCREW (15),
which is used for the METAL BRACKETS to fasten the Hutch
and the Desk together.
å Repeat this step.
7
7
L
SMALL BLACK 5/8" FLAT HEAD SCREW
(8 used in this step)
14

Step 10
Page 14 www.sauder.com/service 428248
å Carefully stand your unit upright.
å Fasten the DOORS (L) to the ENDS (B and C). Use sixteen
SMALL BLACK 5/8" FLAT HEAD SCREWS (14).
å Fasten the KNOB SETS (10) to the DOORS (L). Use two
BLACK 1'" MACHINE SCREWS (12).
BLACK 1" MACHINE SCREW
(2 used for the KNOB SETS)
12
10
10
B
C
L
L
SMALL BLACK 5/8" FLAT HEAD SCREW
(16 used in this step)
14

Step 11
Page 15www.sauder.com/service428248
å Your HUTCH was made to fasten to the 428247 Credenza
or the 428243 L-Desk as shown below.
å Follow Steps 12-13, 18-20 to attach the Hutch to the
428247 Credenza.
å Follow Steps 14-20 to attach the Hutch to the
428243 L-Desk.
428243 L-Desk
428247 Credenza
428243 L-Desk

Step 12
Page 16 www.sauder.com/service 428248
å With someone's help, place your hutch onto the center of the
428247 Credenza.
å Fasten two METAL Z-BRACKETS (5) to the LONG BRACE (J).
Use six BLACK 5/8" FLAT HEAD SCREWS (15).
å NOTE: Position the BRACKETS exactly as shown.
å Fasten the METAL Z-BRACKETS (5) to the edge of the
Credenza top. Use six BLACK 1" FLAT HEAD SCREWS (13).
5
J
428247 Credenza
Pro Tip: Lift with your
legs. And, you know,
your arms.
BLACK 1" FLAT HEAD SCREW
(6 used in this step)
13
BLACK 5/8" FLAT HEAD SCREW
(6 used in this step)
15

Step 13
Page 17www.sauder.com/service428248
å Fasten two METAL L-BRACKETS (6) to the ENDS (B and C). Use four BLACK 5/8" FLAT HEAD SCREWS (15).
å Fasten the METAL L-BRACKETS (6) to the top of the Credenza. With firm pressure, use two BLACK 1" FLAT
HEAD SCREWS (13) through the L-METAL BRACKETS and into the top of your Credenza.
å NOTE: There are no pre-drilled holes in the top of the Credenza. Extra pressure is needed for the SCREWS (13).
å NOTE: Position the BRACKETS exactly as shown.
å Continue to Step 18.
6
6
C
428247 Credenza
BLACK 1" FLAT HEAD SCREW
(2 used in this step)
13
BLACK 5/8" FLAT HEAD SCREW
(4 used in this step)
15
B

Step 14
Page 18 www.sauder.com/service 428248
å Go to Step 16 if you prefer to place your Hutch on the right
section of your L-Desk.
å With someone's help, place your hutch onto the center of the
428243 L-Desk left section.
å Fasten two METAL Z-BRACKETS (5) to the LONG BRACE (J).
Use six BLACK 5/8" FLAT HEAD SCREWS (15).
å NOTE: Position the BRACKETS exactly as shown.
å Fasten the METAL Z-BRACKETS (5) to the edge of the
L-Desk top. Use six BLACK 1" FLAT HEAD SCREWS (13).
5
J
428243 L-Desk
Pro Tip: Lift with your
legs. And, you know,
your arms.
BLACK 1" FLAT HEAD SCREW
(6 used in this step)
13
BLACK 5/8" FLAT HEAD SCREW
(6 used in this step)
15

Step 15
Page 19www.sauder.com/service428248
å Fasten two METAL L-BRACKETS (6) to the ENDS (B and C). Use
four BLACK 5/8" FLAT HEAD SCREWS (15).
å Fasten the METAL L-BRACKETS (6) to the top of the L-Desk.
With firm pressure, use two BLACK 1" FLAT HEAD SCREWS (13)
through the L-METAL BRACKETS and into the top of the L-Desk.
å NOTE: There are no pre-drilled holes in the top of the L-Desk.
Extra pressure is needed for the SCREWS (13).
å NOTE: Position the BRACKETS exactly as shown.
6
6
B
C
428243 L-Desk
BLACK 1" FLAT HEAD SCREW
(2 used in this step)
13
BLACK 5/8" FLAT HEAD SCREW
(4 used in this step)
15

Step 16
Page 20 www.sauder.com/service 428248
å With someone's help, place your Hutch onto center of the
428243 L-Desk right section.
å Fasten two METAL Z-BRACKETS (5) to the LONG BRACE (J).
Use six BLACK 5/8" FLAT HEAD SCREWS (15).
å NOTE: Position the BRACKETS exactly as shown.
å Fasten the METAL Z-BRACKETS (5) to the edge of the L-Desk
top. Use six BLACK 1" FLAT HEAD SCREWS (13).
5
J
428243 L-Desk
BLACK 1" FLAT HEAD SCREW
(6 used in this step)
13
BLACK 5/8" FLAT HEAD SCREW
(6 used in this step)
15