Sauder Craft Table 421417 User manual

Craft Table
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-20
Français p 21-24
Español p 25-28

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-20
21-24
25-28
29-30
31
Skip the power trip.
This time.
Short Screwdriver
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
E SHELF (2)
F BACK (1)
G LONG BASE MOLDING (2)
H SHORT BASE MOLDING (2)
I BRACE (2)
J RAIL EXTENSION (2)
K LEFT DRAWER SIDE (2)
L DRAWER BACK (2)
M RIGHT DRAWER SIDE (2)
N DRAWER BOTTOM (2)
O DRAWER FRONT (2)
P TOP (1)
A
B
C
P
E
E
F
G
G
H
H
I
I
J
J
K
K
L
L
M
M
N
N
O
O
Pae 3421417

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 47
3
CAM COVER CARD - 5
7
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4
WOOD DOWEL - 1
5KNOB - 2
6
RIGHT FILE GLIDE - 2
810 ELECTRICAL CORD - 1
SILVER 1/2" FLAT HEAD SCREW - 16
15
SILVER 13/16" PAN HEAD SCREW - 8
14
SILVER 1-3/16" FLAT HEAD SCREW - 8
11 SILVER 1-3/16" PAN HEAD SCREW - 6 12
LEFT FILE GLIDE - 2
9
CAM SCREW - 47
4
Pae 4 421417
16 SILVER 1116" MACHINE SCREW  2 17 1116" PAN HEAD SCREW  8
METAL BRACKET - 4
18 WASHER - 2
19

Step 1
Arrow
3
F
C
B
A
Mx 2
Ix 2
Kx 2
Ex 2
Arrow
Arrow
3
Arrow
3
å Push forty-seven HIDDEN CAMS (3) into the ENDS (A
and B), UPRIGHT (C), SHELVES (E), BACK (F), BRACES (I),
LEFT DRAWER SIDES (K and M).
3
Arrow
3
Arrow
3
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
(47 used)
Page 5

Step 2
4
å
Turn forty-five CAM SCREWS (4) into the ENDS (A and B),
UPRIGHT (C), TOP (P), SHORT BASE MOLDINGS (H), and
DRAWER FRONTS (O).
å
NOTE: Two CAMS SCREWS will be used in step 11.
Ox 2
Hx 2
P
C
B
A
Page 6

å Fasten the RAIL EXTENSIONS (J) to the LEFT END (B)
and UPRIGHT (C). Use eiht SILVER 13/16" FLAT HEAD
SCREWS (14).
å Fasten the LONG BASE MOLDINGS (G) to the LEFT
END (B) and UPRIGHT (C). Use six SILVER 1-3/16" PAN
HEAD SCREWS (12).
Step 3
C
B
SILVER 13/16" FLAT HEAD SCREW
(8 used for the EXTENSION RAILS)
14
J
J
Surface with more holes
Surface with more holes
G
G
Curved ede
SILVER 1-3/16" FLAT HEAD SCREW
(6 used for the BASE MOLDINGS)
12
Pae 7
Remember:
Rihty tihty.
Lefty loosey.

Step 4
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the LEFT END (B) and UPRIGHT (C).
Use eight SILVER 1/2" FLAT HEAD SCREWS (15).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlarged diagram. Then, slide the inner cartridge of the EXTENSION
RAIL in to find the other hole that lines up with the hole in the END and
UPRIGHT. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Open end
Open end
Open end
1
1
1
1
C
B
Page 8
SILVER 1/2" FLAT HEAD SCREW
(8 used in this step)
15
Push up on the black lever and pull the SLIDE from the RAIL.
2
1

å Fasten the SHELVES (E) to the UPRIGHT (C). Tighten six
HIDDEN CAMS.
Step 5
1
2
Page 9
Surface with HIDDEN CAMS
C
E
E
Surface with
HIDDEN CAMS

å Fasten the BRACES (I) to the UPRIGHT (C). Tighten four
HIDDEN CAMS.
Step 6
1
2
I
I
Surface with HIDDEN CAMS
Page 10
C
Finished edge
Finished edge