Sauder 413072 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-24
Français...............Pages 25-28
Espanol.............Páginas 29-32
Lot #: 354461 07 / 01 / 13
Date Purchased: ____________________
413072
Desk

ASSEMBLY TOOLS REQUIRED
Hammer
Tip Shown Actual Size
No. 2 Phillips Screwdriver
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .........4-5
Assembly Steps....................6-24
Français..............................25-28
Espanol...............................29-32
Safety .................................33-34
Warranty...................................35
Page 2 www.sauder.com/services 413072

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C UPRIGHT 1
D TOP 1
E BOTTOM 1
F MODESTY PANEL 1
G SHELF 1
H KEYBOARD SHELF 1
I BACK 1
J DOOR 1
K ADJUSTABLE SHELF 1
L KEYBOARD FRONT 1
M KEYBOARD BACK 1
N KEYBOARD SIDE 2
O DRAWER FRONT 1
D74 DRAWER BACK 1
D46 RIGHT DRAWER SIDE 1
D47 LEFT DRAWER SIDE 1
D707 DRAWER BOTTOM 1
T SKIRT 1
Page 3
www.sauder.com/services413072
A
B
C
D
E
F
G
H
I
J
K
L
MN
O
D74 D46
D47
T
N
D707

HARDWARE IDENTIFICATION
Page 4 www.sauder.com/services 413072
TWIST-LOCK® FASTENER - 1
CC
ANGLE BRACKET - 6
HH
RUBBER SLEEVE - 4
NN
SCREW COVER - 8
LL METAL PIN - 6
MM
CAM DOWEL - 6
EE2
HIDDEN CAM - 6
DD2
GG KEYBOARD
HINGE - 2
FF HINGE - 2
DOOR STOP - 2
KK
PULL - 3
JJ
35AW CABINET RIGHT - 1 35AX CABINET LEFT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1
ULONG RIGHT
CABINET RAIL - 1 VLONG LEFT
CABINET RAIL - 1 XLONG LEFT
DRAWER SLIDE - 1
WLONG RIGHT
DRAWER SLIDE - 1
DRAWER FRONT BRACKET - 1
II

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 5
www.sauder.com/services413072
BLACK 9/16" LARGE HEAD SCREW - 14
VV
BLACK 1-7/8" FLAT HEAD SCREW - 11
OO
BROWN 1-1/2" FLAT HEAD SCREW - 6
QQ
BROWN 1" FLAT HEAD SCREW - 4
SS
GOLD 5/16" FLAT HEAD SCREW - 12
YY
SILVER 5/8" FLAT HEAD SCREW - 4
UU
SILVER 9/16" LARGE HEAD SCREW - 2
WW
BLACK 1-1/4" FLAT HEAD SCREW - 2
RR
BLACK 1/2" FLAT HEAD SCREW - 4
XX
NAIL - 22
ZZ
SILVER 7/8" MACHINE SCREW - 6
TT
BLACK 1-9/16" FLAT HEAD SCREW - 4
PP

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (CC) into the large hole in the MODESTY PANEL (F).
Page 6 www.sauder.com/services 413072
Do not tighten the TWIST-LOCK® FASTENERS in this step.
F
CC

2
2
S
t
e
p
Page 7
www.sauder.com/services413072
Push six HIDDEN CAMS (DD2) into the ENDS (A and B) and UPRIGHT (C). Then, insert the metal end of a CAM DOWEL (EE2)
into each HIDDEN CAM.
Do not tighten the HIDDEN CAMS in this step.
(6 used)
A
B
C
Arrow
DD2
EE2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

3
3
S
t
e
p
Page 8 www.sauder.com/services 413072
Fasten the LONG RIGHT CABINET RAIL(U) to the RIGHT END (A) and the LONG LEFT CABINET RAIL (V) to the UPRIGHT (C).
Use four GOLD 5/16" FLAT HEAD SCREWS (YY) through holes #1 and #4.
NOTE: The CABINET RAILS are marked "CABINET RIGHT" and "CABINET LEFT" for easy identification.
GOLD 5/16" FLAT HEAD SCREW
(4 used for the in this step)
YY
1
2
34
43
2
1
Finished edge
Finished edge
Roller end
Roller end
A
C
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
U
V

4
4
S
t
e
p
Page 9
www.sauder.com/services413072
Fasten the CABINET LEFT (35AX) to the LEFT END (B) and the CABINET RIGHT (35AW) to the UPRIGHT (C). Use four GOLD 5/16"
FLAT HEAD SCREWS (YY).
Finished edge
Finished edge
B
C
Surface with
HIDDEN CAMS Surface without
HIDDEN CAMS
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used for the in this step)
YY

Fasten the LEFT END (B) to the TOP (D). Tighten two HIDDEN CAMS.
Fasten the MODESTY PANEL (F) to the TOP (D). Tighten a TWIST-LOCK®FASTENER.
Fasten the MODESTY PANEL (F) to the LEFT END (B). Use three BLACK 1-7/8" FLAT HEAD SCREWS (OO).
5
5
S
t
e
p
Page 10 www.sauder.com/services 413072
Dowel end
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must remain
fully inserted in the hole of the adjoining part while
locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver
as tight as possible.
B
F
D
Surface with
HIDDEN CAMS
Surface with holes
Long finished edge
Finished edge
Surface with
TWIST-LOCK®
FASTENERS
Notch
BLACK 1-7/8" FLAT HEAD SCREW
(3 used in this step)
OO
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow

6
6
S
t
e
p
Page 11
www.sauder.com/services413072
Fasten two ANGLE BRACKETS (HH) to the SHELF (G). Use two BLACK 9/16" LARGE HEAD SCREWS (VV).
NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the SHELF.
Insert two METAL PINS (MM) into the SHELF (G).
Fasten the SHELF (G) to the LEFT END (B). Use a BLACK 1-7/8" FLAT HEAD SCREW (OO).
NOTE: Be sure the METAL PIN (MM) in the SHELF (G) inserts into the hole in the LEFT END (B).
Fasten the SHELF (G) to the MODESTY PANEL (F). Use two BLACK 9/16" LARGE HEAD SCREWS (VV) through the ANGLE
BRACKETS on the SHELF and into the MODESTY PANEL.
BLACK 9/16" LARGE HEAD SCREW
(4 used for the ANGLE BRACKETS)
VV
F
HH
G
MM
Surface with holes
(2 used)
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(1 used in this step)
OO
B

Fasten the UPRIGHT (C) to the TOP (D). Tighten two HIDDEN CAMS.
Fasten the UPRIGHT (C) to the MODESTY PANEL (F) and SHELF (G). Use three BLACK 1-7/8" FLAT HEAD SCREWS (OO).
NOTE: Be sure the METAL PIN in the SHELF (G) inserts into the hole in the UPRIGHT (C).
Push the DOOR STOPS (KK) into the holes in the UPRIGHT (C) and TOP (D).
7
7
S
t
e
p
Page 12 www.sauder.com/services 413072
F
G
D
C
Surface with
HIDDEN CAMS
BLACK 1-7/8" FLAT HEAD SCREW
(3 used in this step)
OO
Finished edge
KK
KK
Maximum
210 degrees
Minimum
190 degrees
Arrow

8
8
S
t
e
p
Page 13
www.sauder.com/services413072
C
A
E
Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (OO).
Fasten the RIGHT END (A) to the TOP (D). Tighten two HIDDEN CAMS.
Fasten the RIGHT END (A) to the BOTTOM (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (OO).
Surface without
HIDDEN CAMS
Finished edge
Surface with
holes
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
OO
These holes
must be here.
D
Maximum
210 degrees
Minimum
190 degrees
Arrow

Fasten four ANGLE BRACKETS (HH) to the BOTTOM (E) and SKIRT (T). Use four BLACK 9/16" LARGE
HEAD SCREWS (VV).
NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the BOTTOM and SKIRT.
Fasten the SKIRT (T) to the RIGHT END (A), UPRIGHT (C), and BOTTOM (E). Use four BLACK 9/16"
LARGE HEAD SCREWS (VV).
9
9
S
t
e
p
Page 14 www.sauder.com/services 413072
BLACK 9/16" LARGE HEAD SCREW
(8 used for the ANGLE BRACKETS)
VV
E
T
T
C
A
HH
HH
HH

10
10
S
t
e
p
Page 15
www.sauder.com/services413072
Carefully turn your unit over onto its front edges. Lay the BACK (I) over your unit.
Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square".
Fasten the BACK (I) to your unit using the NAILS (ZZ).
NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(22 used in this step)
ZZ
I
The hole should be here

11
11
S
t
e
p
Page 16 www.sauder.com/services 413072
Carefully stand your unit upright.
Fasten the HINGES (FF) to the DOOR (J). Use four BLACK 1/2" FLAT HEAD SCREWS (XX).
Fasten the DOOR (J) to the RIGHT END (A). Use the screws in the HINGES. See the next step for door adjustments.
NOTE: You may need to loosen the mounting screw and adjusting screw to slide them part way out of the slot. Retighten the screw
before you mount the HINGE to the MOLDING.
Fasten a PULL (JJ) to the DOOR (J). Use two SILVER 7/8" MACHINE SCREWS (TT).
BLACK 1/2" FLAT HEAD SCREW
(4 used for the HINGES)
XX
FF
SILVER 7/8" MACHINE SCREW
(2 used for the PULL)
TT
J
J
JJ
A
Mounting screw
Adjusting screw

12
12
S
t
e
p
Page 17
www.sauder.com/services413072
Refer to the enlarged diagram to identify the parts on the HINGES.
The DOORS may need some adjustments. Follow the text below to make needed adjustments.
DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out.
Tighten the mounting screw after making adjustments.
To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired
location. Tighten the screws after making adjustments.
To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the
mounting screw after making adjustments.
Mounting screw (depth)
Adjusting screw
(horizontal)
(vertical adjustment)

13
13
S
t
e
p
Page 18 www.sauder.com/services 413072
Fasten the KEYBOARD SIDES (N) to the KEYBOARD SHELF (H). Use four BROWN 1-1/2" FLAT HEAD SCREWS (QQ).
Fasten the KEYBOARD SIDES (N) to the KEYBOARD BACK (M). Use two BROWN 1-1/2" FLAT HEAD SCREWS (QQ).
Fasten the KEYBOARD BACK (M) to the KEYBOARD SHELF (H). Use two BLACK 1-1/4" FLAT HEAD SCREWS (RR).
H
M
N
N
These holes must
be facing up.
Finished surface
BLACK 1-1/4" FLAT HEAD SCREW
(2 used in this step)
RR
BROWN 1-1/2" FLAT HEAD SCREW
(6 used in this step)
QQ
Short finished edge
Short finished edge

Fasten the KEYBOARD HINGES (GG) to the KEYBOARD FRONT (L). Use four SILVER 5/8" FLAT HEAD SCREWS (UU).
Fasten the KEYBOARD HINGES (GG) to the KEYBOARD SHELF (H). Use two SILVER 9/16" LARGE HEAD SCREWS (WW).
14
14
S
t
e
p
Page 19
www.sauder.com/services413072
SILVER 5/8" FLAT HEAD SCREW
(4 used in this step)
UU
SILVER 9/16" LARGE HEAD SCREW
(2 used in this step)
WW
L
H
GG

15
15
S
t
e
p
Page 20 www.sauder.com/services 413072
Fasten the DRAWER RIGHT (35AY) and DRAWER LEFT (35AZ) to the KEYBOARD SHELF (H). Use four BROWN 1" FLAT
HEAD SCREWS (SS).
Fasten a PULL (JJ) to the KEYBOARD FRONT (L). Use two SILVER 7/8" MACHINE SCREWS (TT).
Roller end
Roller end
L
H
JJ
BROWN 1" FLAT HEAD SCREW
(4 used for the DRAWER SLIDES)
SS
SILVER 7/8" MACHINE SCREW
(2 used for the PULL)
TT