Sauder East Canyon Series User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-28
Français p 29-32
Español p 33-36
Lot # 387943 01/13/16
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Gun Display Cabinet
East Canyon Collection | Model 419342
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
WARNING
This cabinet provides limited
security for lon uns and is
not intended for handuns,
youth uns or other firearms.

Table of Contents Assembly Tools Required
3
4-5
6-28
29-32
33-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
419342 www.sauder.com/servicesPae 2
Tape Measure
WARNING
Please use your furniture correctly and safely. Proper un storae can help prevent accidents. Improper use
can cause safety hazards,or damae to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Unauthorized access to uns or
ammunition by a child or unauthorized
persons.
• Leavin the cabinet unlocked and
unattended.
• Risk of serious injury or death. • Always store uns UNLOADED and
locked in the cabinet when not in use.
• Store the ammunition in a locked location
separate from uns.
• Keep un cabinet keys away from children
and unauthorized persons.
• ALWAYS comply with safe un storae
laws and recommendations. This cabinet
provides limited security for lon uns and
is not intended for handuns, youth uns or
other firearms.
• Check the security of uns once the tube
set is locked in place.
• Improperly movin furniture that is not
desined and equipped with casters. • Furniture can tip over or break if improperly moved.
• Physical injury. Furniture can be very heavy.
• Do not push furniture, especially on a
carpeted floor. Have a friend help you lift
the item and set it in place.
Scissors

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A2 RIGHT END (1)
B2 LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK PANEL (2)
G BARREL REST (1)
H LOWER DOOR (1)
I RIGHT DOOR (1)
J LEFT DOOR (1)
K STOCK REST (1)
L FRONT SKIRT (1)
M TOP MOLDING (1)
N2 RACK MOLDING (1)
O BOTTOM MOLDING (1)
Now you know
our ABCs.
419342www.sauder.com/services Pae 3
A2
B2
C
D
E
F
G
H
I
J
K
L
M
N2
O
F

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419342 www.sauder.com/servicesPae 4
31G CORNER
BRACKET - 2
TUBE SET - 1
85M
WARNING
Non-load Bearin Surface
Do not place items such as ammunition boxes or other
accessories on this surface.
Do not use this surface as a step.
- The cabinet could become unstable and may tip.
Refer to instruction book for complete safety
information.
Note: This is a permanent label. Do not try to remove.
Surface will be damaed.
05/15 3 7 4 0 3 6 374036
WARNING LABEL - 1
10L
(Refer to the last step for proper
location and application)
SAFETY
BRACKET - 1
1G METAL
BRACKET - 2
4G
HIDDEN
CONNECTOR - 4
5F
FELT STRIP - 1
84M
CAM
COVER - 23
13P
SLIDE CATCH - 2
6J
TACK
GLIDE - 6
13E CAM
SCREW - 6
8F
DOOR STOP - 1
4I
LOCK COVER - 2
10J
STRIKE PLATE - 1
6I
HIDDEN
CAM - 34
1F CAM
DOWEL - 20
2F
PULL - 2
101K
13H STRAIGHT
HINGE - 6
19H CURVED
HINGE - 2
LOCK - 1
12J
BUSHING
CONNECTOR - 4
8I
LOCK - 1
13J
DOUBLE
DOWEL - 4
22F
WARNING
• Severe injury and death can occur when
unauthorized or untrained persons, includin
children, use uns.
• Guns should always be unloaded and locked
when stored.
• Ammunition should be stored and locked
separately from uns.
• Always comply with safe un storae laws and
recommendations. This cabinet/bench provides
limited security for lon uns, and is not intended
for handuns and other firearms. 373366
WARNING LABEL - 1
9L
(Refer to the last step for proper
location and application)
DIVIDER - 9
89M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419342www.sauder.com/services Pae 5
SILVER 3/4" MACHINE SCREW - 4
20S
BLACK 9/16" LARGE HEAD SCREW - 17
1S CONNECTOR SCREW - 4 8S
BROWN 1-1/2" FLAT HEAD SCREW - 4
14S12S BROWN 1" FLAT HEAD SCREW - 4
SILVER 5/8" FLAT HEAD SCREW - 4
23S
BLACK 1/2" FLAT HEAD SCREW - 17
11S
16S BLACK 1-7/8" PAN HEAD SCREW - 1
RECOMMENDED PADLOCK
- NOT PROVIDED
BLACK 1-1/8" PAN HEAD SCREW - 3
9S
BLACK 1-3/8" PAN HEAD SCREW - 14
118S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
419342 www.sauder.com/servicesPae 6
å Insert a CONNECTOR SCREW (8S) into each
HIDDEN CONNECTOR (5F).
å Assemble your unit on a carpeted floor or on the
empty carton to avoid scratchin your unit or the floor.
å Use your hammer to tap a HIDDEN CONNECTOR
with SCREW into each of the lare holes in the
BARREL REST (G).
Step 2
8S
5F
G
5F
5F
5F

Step 3
419342www.sauder.com/services Pae 7
å NOTE: Do not peel the backin completely o of the FELT STRIP (84M).
å Partially peel the paper o the back of the FELT STRIP (84M), ivin yourself enouh of the FELT STRIP to cover the first
couple of inches of the BARREL REST (G).
å IMPORTANT: Do not pull tihtly on the FELT STRIP as you apply it to the BARREL REST. Pullin the strip tiht as you apply
it will cause the felt to separate from the ede of the board.
å Apply the FELT STRIP (84M) to the BARREL REST (G). Start the exposed end of the FELT STRIP at one end of the
BARREL REST and firmly press, do not pull, on the FELT STRIP. Work your way down the BARREL REST. Trim any excess
FELT STRIP o with your scissors.
å NOTE: When pullin back the release paper on the FELT STRIP, be sure you do not pull on any of the FELT STRIP already
applied to the BARREL REST.
å Turn six CAM SCREWS (8F) into the MOLDINGS (M and O).
G
84M
8F
(6 used)
O
M

Step 4
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
å Push thirty-four HIDDEN CAMS (1F) into the TOP (C),
BOTTOM (D), SHELF (E), and BACK PANELS (F). Then,
insert the metal end of twenty CAM DOWELS (2F) into
some of the HIDDEN CAMS. Follow the diaram closely.
(34 used)
(20 used)
Arrow
1F
2F
Do not tihten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edes.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not insert
CAM DOWELS
into these edes.
C
D
E
F
F
419342 www.sauder.com/servicesPae 8

StepStep 5
å Insert four DOUBLE DOWELS (22F) into the BACK PANELS (F).
å Fasten the BACK PANELS (F) toether. Tihten eiht HIDDEN CAMS.
22F
22F
These holes
must be here.
These holes
must be here.
Surface with
HIDDEN CAMS
F
Surface with
HIDDEN CAMS
F
419342www.sauder.com/services Pae 9
1
2

StepStep 6
å Fasten the BARREL REST (G) to the BACK PANELS (F).
Tihten two HIDDEN CONNECTORS.
Surface with
HIDDEN CAMS
F
Surface with
HIDDEN CAMS
F
G
Surface with
HIDDEN CONNECTORS
How to use the HIDDEN CONNECTOR
To fasten two parts together using the
HIDDEN CONNECTORS, insert your
screwdriver, at an angle, into the slot in the
HIDDEN CONNECTOR. While pushing the
screw into the hole of the adjoining part,
turn the screwdriver clockwise to tighten.
419342 www.sauder.com/servicesPae 10

å Fasten two DIVIDERS (89M) to the ENDS (A2 and B2) exactly as
shown. Use four BROWN 1" FLAT HEAD SCREWS (12S).
Step 7
419342www.sauder.com/services Pae 11
B2
A2
BROWN 1" FLAT HEAD SCREW
(4 used in this step)
12S
12S
89M
89M
12S
Surface
with
holes
Surface
with
holes
Finished ede
Finished ede

Step 8
å Fasten the LEFT END (B2) to the left BACK PANEL (F).
Tihten four HIDDEN CAMS.
å Fasten the LEFT END (B2) to the BARREL REST (G).
Tihten one HIDDEN CONNECTOR.
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
F
G
B2
Finished ede
Surface with holes
419342 www.sauder.com/servicesPae 12

419342www.sauder.com/services Pae 13
å Fasten the TOP (C) to the LEFT END (B2). Tihten two
HIDDEN CAMS.
å Insert the DOOR STOP (4I) into the smaller hole in
the TOP (C).
Step 9
4I
C
B2
Surface without
HIDDEN CAMS
These holes
must be here.
Arrow
Minimum
190 derees
Maximum
210 derees

Step 10
å Fasten the BOTTOM (D) and SHELF (E) to the LEFT
END (B2). Tihten four HIDDEN CAMS. Arrow
Minimum
190 derees
Maximum
210 derees
Surface with HIDDEN CAMS
These holes
must be here.
Groove
B2
E
Surface with HIDDEN CAMS
D
419342 www.sauder.com/servicesPae 14

Step
419342www.sauder.com/services Pae 15
Step 11
å Slide seven DIVIDERS (89M) onto the RACK MOLDING (N2) so the
holes in the DIVIDERS line up with the holes in the RACK MOLDING.
å NOTE: The DIVIDERS (89M) should all face the same direction.
å Fasten these seven DIVIDERS (89M) to the RACK MOLDING (N2). Use
fourteen BLACK 1-3/8" PAN HEAD SCREWS (118S).
N2
89M
(7 used)
BLACK 1-3/8" PAN HEAD SCREW
(14 used in this step)
118S

Step
å Insert the RACK MOLDING (N2) into the DIVIDER (89M)
on the LEFT END (B2) and position as shown.
å Insert the other end of the RACK MOLDING (N2) into the
DIVIDER (89M) on the RIGHT END (A2) before fastenin
the RIGHT END (A2) to the assembled parts.
å Fasten the RIGHT END (A2) to the TOP (C), BOTTOM (D),
and SHELF (E), and riht BACK PANEL (F). Tihten ten
HIDDEN CAMS.
å Fasten the RIGHT END (A2) to the BARREL REST (G).
Tihten one HIDDEN CONNECTOR.
Step 12
Arrow
Minimum
190 derees
Maximum
210 derees
E
D
A2
G
C
Finished ede
Surface without holes
419342 www.sauder.com/servicesPae 16
F
B2
N2
89M

StepStep 13
å Fasten the TOP MOLDING (M) to the TOP (C). Tihten
three HIDDEN CAMS.
å Fasten the BOTTOM MOLDING (O) to the BOTTOM (D).
Tihten three HIDDEN CAMS.
å Fasten the STOCK REST (K) to the SHELF (E). Use three
BLACK 1-1/8" PAN HEAD SCREWS (9S).
å NOTE: There are no pre-drilled holes in the STOCK REST.
The SCREWS will tihten into the roove.
1
2
Wide ede
Unfinished surface
Groove
E
D
C
O
K
M
419342www.sauder.com/services Pae 17
BLACK 1-1/8" PAN HEAD SCREW
(3 used for the STOCK REST)
9S

Step
å Fasten two METAL BRACKETS (4G) to the BOTTOM (D).
Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edes of the METAL BRACKETS are
even with the edes of the BOTTOM.
å Fasten two CORNER BRACKETS (31G) to the ENDS (A
and B) and BOTTOM (D). Use eiht BLACK 9/16" LARGE
HEAD SCREWS (1S).
å Fasten the FRONT SKIRT (L) to the ENDS (A and B)
and BOTTOM (D). Use six BLACK 9/16" LARGE HEAD
SCREWS (1S) throuh the BRACKETS and into the
FRONT SKIRT.
Step 14
D
A
B
L
BLACK 9/16" LARGE HEAD SCREW
(16 used in this step)
1S
Surface without holes
31G
4G
31G
419342 www.sauder.com/servicesPae 18
You may need to loosen
the CORNER BRACKET
screws to line up the holes.

StepStep 15
å Usin your hammer, ently tap six TACK GLIDES (13E) into
the edes of the ENDS (A and B) and FRONT SKIRT (L).
13E
13E
A
B
L
Now miht be a
ood time to refresh
your drink.
419342www.sauder.com/services Pae 19

Step
å Fasten two CURVED HINGES (19H) to the LOWER DOOR (H).
Use four BLACK 1/2" FLAT HEAD SCREWS (11S).
å Fasten six STRAIGHT HINGES (13H) to the DOORS (I and J).
Use twelve BLACK 1/2" FLAT HEAD SCREWS (11S).
Step 16
BLACK 1/2" FLAT HEAD SCREW
(16 used in this step)
11S
13H
19H
13H
I
J
H
419342 www.sauder.com/servicesPae 20