Sauder Barrister Lane 422268 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-26
Español pg 27-29
Lot # 504610 06/12/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Smart Center Side Table
Barrister Lane Collection | Model 422268
Plus up a room.
Plug in your life.

Table of Contents Assembly Tools Required
3
4
5-23
24-26
27-29
30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
422268 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C FIXED TOP (1)
D SLIDING TOP (1)
E BACK (1)
F RIGHT DRAWER UPRIGHT (1)
G LEFT DRAWER UPRIGHT (1)
H SHELF (1)
I FRONT/BACK MOLDING (2)
J SIDE MOLDING (2)
K BOTTOM (1)
L FRONT/BACK SKIRT (2)
M SIDE SKIRT (2)
N RIGHT FRONT/LEFT REAR LEG (2)
O LEFT FRONT/RIGHT REAR LEG (2)
P SHELF MOLDING (1)
Q DRAWER FRONT (1)
Now you know
our ABCs.
A
B
C
D
E
F
G
H
I
J
K
LM
N
O
P
Q
I
J
M
L
O
N
422268www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
422268 www.sauder.com/servicesPage 4
(EXTENSION SET SHOWN SEPARATED)
REXTENSION RAIL - 2 SEXTENSION SLIDE - 2 OUTLET - 1
6D
HIDDEN CAM - 38
1F CAM DOWEL - 20 2F CAM SCREW - 18 8F 10F TWIST-LOCK®
FASTENER - 12
MAGNETIC CATCH - 1
3I STRIKE PLATE - 1 6I KNOB - 4
71K CORD CLIP - 2
4P
GROMMET - 1
7P CAM COVER - 16 13P SUPPORT PIN - 2 5R
3S GOLD 5/16" FLAT HEAD SCREW - 8 BLACK 1/2" FLAT HEAD SCREW - 1 11S
BROWN 1-1/2" FLAT HEAD SCREW - 2
14S BLACK 9/16" PAN HEAD SCREW - 2 25S
BLACK 7/8" MACHINE SCREW - 4
37S BLACK 1-15/16" FLAT HEAD SCREW - 6
113S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (10F) into the large holes in the ENDS (A
and B), BACK (E), DRAWER UPRIGHTS (F and G), and
DRAWER FRONT (Q).
422268www.sauder.com/services Page 5
(12 used)
10F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
10F
10F
10F
A
B
E
F
G
Q

Step 2
å Push twenty HIDDEN CAMS (1F) into the MOLDINGS (I
and J) and BOTTOM (K). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
å NOTE: Use the exact holes shown.
422268 www.sauder.com/servicesPage 6
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
2F
(20 used)
Do not tighten the HIDDEN CAMS in this step.
1F
2F
Arrow
Arrow
1F
2F
I
J
J
I
K

å Push eighteen HIDDEN CAMS (1F) into the DRAWER UPRIGHTS (F
and G), MOLDINGS (I and J), and SKIRTS (L and M).
Step 3
I
J
L
M
J
M
L
I
422268www.sauder.com/services Page 7
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1F
Arrow
(18 used)
Arrow
1F
F
G
Just think. The sooner
you do this, the sooner
you do something else.

Step 4
å Turn eighteen CAM SCREWS (8F) into the LEGS (N and O)
and DRAWER FRONT (Q).
N
O
O
N
422268 www.sauder.com/servicesPage 8
8F
8F
Q
(18 used)

Step 5
422268www.sauder.com/services Page 9
å Separate the EXTENSION SLIDES (S) from the EXTENSION RAILS (R) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (R) to the ENDS (A and B). Use four GOLD 5/16"
FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the
enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to
find the other hole that lines up with the hole in the END. Turn a SCREW into
this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWER UPRIGHTS.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
RS
Push the black lever in and pull the SLIDE from the RAIL.
Open end
Open end
A
B
R
R
This hole
must be here.

Step 6
å Insert the GROMMET (7P) into the large hole in the SHELF (H).
å Fasten the OUTLET (6D) to the SHELF (H). Use two BLACK
9/16" PAN HEAD SCREWS (25S).
å NOTE: Be sure to position the OUTLET exactly as shown.
å Fasten the SHELF MOLDING (P) to the SHELF (H). Use two
BROWN 1-1/2" FLAT HEAD SCREWS (14S).
å Insert the MAGNETIC CATCH (3I) into the hole in the SHELF (H).
422268 www.sauder.com/servicesPage 10
Surface with fewer holes
HP
Rounded edge
Edge without holes
BROWN 1-1/2" FLAT HEAD SCREW
(2 used for the SHELF MOLDING)
14S
6D
7P
3I
BLACK 9/16" PAN HEAD SCREW
(2 used for the OUTLET)
25S