Sauder Viabella 420870 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-14
Français pg 15-16
Español pg 17-18
Lot # 500737 05/23/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Legitimizing bedrooms
everywhere.
Full/Queen Headboard
Viabella Collection | Model 420870

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-14
15-16
17-18
19
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Warranty
420870 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP PANEL (1)
B WALL BRACE (2)
C LONG MOLDING (2)
D SHORT MOLDING (2)
E RIGHT LEG (1)
F LEFT LEG (1)
G CENTER PANEL (1)
H LEG CAP (2)
A
B
C
D
E
F
G
C
D
B
H
H
420870www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SILVER 1-1/8" FLAT HEAD SCREW - 19
10S
BLACK 1-7/8" FLAT HEAD SCREW - 4
2S
HEADBOARD BRACKET - 2
42G
CAM SCREW - 8
8F WOOD DOWEL - 4 15F
HIDDEN CAM - 8
1F
NUT - 8
24M
WASHER - 8
13M
BUMPER - 4
2M GLUE - 1 54M
GOLD 2-3/4" FLAT HEAD BOLT - 4
109S SILVER 1-1/4" BOLT - 4 117S
420870 www.sauder.com/servicesPage 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1F) into the TOP PANEL (A)
and CENTER PANEL (G).
420870www.sauder.com/services Page 5
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
G
(8 used) 1F
Arrow Meet Part (G). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
headboard that’s easier to assemble
and friendlier to the environment.

Step 2
420870 www.sauder.com/servicesPage 6
8F
å Turn eight CAM SCREWS (8F) into the LEGS (E and F).
E
F

SILVER 1-1/8" FLAT HEAD SCREW
(4 used in this step)
10S
å Fasten two SHORT MOLDINGS (D) to the CENTER PANEL (G).
Use four SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 3
420870www.sauder.com/services Page 7
G
D
D
Surface with HIDDEN CAMS
Remember:
Righty tighty.
Lefty loosey.

Step 4
420870 www.sauder.com/servicesPage 8
å Fasten two LONG MOLDINGS (C) to the CENTER PANEL (G).
Use ten SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
SILVER 1-1/8" FLAT HEAD SCREW
(10 used in this step)
10S
C
C
Unfinished surface
Unfinished surface
Use outside holes
Use inside holes
G
Surface with HIDDEN CAMS

å Fasten the TOP PANEL (A) to one of the LONG MOLDINGS (C) as
shown below. Use five SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 5
420870www.sauder.com/services Page 9
A
SILVER 1-1/8" FLAT HEAD SCREW
(5 used in this step)
10S
C
Surface with HIDDEN CAMS

å Fasten two WALL BRACES (B) to the CENTER PANEL (G).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 6
420870 www.sauder.com/servicesPage 10
B
B
G
Surface with
more holes
Surface with
more holes
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S