Sauder Harvey Park 414986 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Share your journey!
Your holder for all
things awesome.
Need help? Visit our web to view video assembly tips or chat with a live rep.
Prefer the phone?
Enlish p 1-21
Français p 22-24
Español p 25-27
Be sure to ive us a rin before
makin any returns.
Credenza

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Use of a TV that is too heavy or lare is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too lare for the available space miht be accidentally pushed or bumped o the furniture, or subject to tip-over.
t within the space defined in the diaram.
• Never place the front ede of the TV past the front ede of the TV support shelf (or stop moldin – if equipped)
• Never allow the sides of the TV to extend past the side edes of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warnin label as instructed in the last assembly step. The label provides important safety related information.
3
4
5-21
22-24
25-27
28-30
31
Table of Contents
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Assembly Tools Required
135 lbs.
135 lbs.
71"
71"
19"
19"
WARNING
Pae 2
• Check the size and weiht of your TV. Compare it to the diaram below – before you begin assembly!
• This unit is desined for use with televisions weihin less than 135 pounds. Never use with a TV that weihs more.• The
size of the television, front-to-back and side-to-side, must fi

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A2
B2
C
C
D
D
E2
F
G2
H
I
J
K
L
M
N
N
O
O
O
D115
D723
D13
D12
M67
A2 RIGHT END (1)
B2 LEFT END (1)
C UPRIGHT (2)
D LOWER UPRIGHT (2)
D12 RIGHT DRAWER SIDE (3)
D13 LEFT DRAWER SIDE (3)
D115 DRAWER BACK (3)
D723 DRAWER BOTTOM (3)
E2 TOP (1)
F BOTTOM (1)
G2 SHELF (1)
H BACK (1)
I BRACE (1)
J DRAWER FRONT (1)
K RIGHT DRAWER FRONT (1)
L LEFT DRAWER FRONT (1)
M BASE (1)
M67 DRAWER BRACE (3)
N SIDE BASE (2)
O MOLDING (9)
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
35GA CABINET RIGHT - 3 35GB CABINET LEFT - 3 35GC DRAWER RIGHT - 3 35GD DRAWER LEFT - 3
1F HIDDEN CAM - 15 2F CAM DOWEL - 15 10F TWIST-LOCK®FASTENER - 8
10A SLIDE CAM - 6
31G CORNER BRACKET - 4 84K PULL - 3
1N NAIL - 42 36P CAM COVER - 4
3S GOLD 5/16" FLAT HEAD SCREW - 24
2S BLACK 1-7/8" FLAT HEAD SCREW - 8
12S BROWN 1" FLAT HEAD SCREW - 36
1S BLACK 9/16" LARGE HEAD SCREW - 38
(Refer to the last step for proper
location and application)
4L WARNING LABEL - 1
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 135 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete safety
information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
30S BLACK 1-9/16" FLAT HEAD SCREW - 15
29M BUMPER CARD - 2
4G METAL BRACKET - 4
Pae 4

Step 1
10F
(8 used)
A2
B2
Do not tihten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å
Some assembly
(and snacks) required.
Meet Parts (A2 and B2). These
components have been enineered to
be lihter, stroner, faster… well ok. Not
technically faster. But definitely makes for a
sturdier Credenza that’s easier to assemble
and friendlier to the environment.
To bein assembly, push a TWIST-LOCK® FASTENER
(10F) into the lare holes in the ENDS (A2 and B2).
Repeat this step for the SHELF (G2).
Pae 5

Step
å Push fifteen HIDDEN CAMS (1F) into the UPRIGHTS (C
and D), BOTTOM (F), and DRAWER BRACES (M67). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Step 2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(15 used)
(15 used)
Arrow
1F
2F
Arrow
1F
2F
C
C
D
D
F
M67
M67
M67
Do not tihten the HIDDEN CAMS in this step.
Pae 6

StepStep 3
å
1
2
3
Surface with
TWIST-LOCK
®
FASTENERS
Surface with
TWIST-LOCK
®
FASTENERS
B2
A2
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
1
2
3
Fasten a CABINET RIGHT (35GA) to the RIGHT END (A2)
and a CABINET LEFT (35GB) to the LEFT END (B2). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
Pae 7

Step 4
å Fasten the CABINET RIGHTS (35GA) and CABINET
LEFTS (35GB) to the LOWER UPRIGHTS (D). Use
eiht GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
Finished ede
Finished ede
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
Roller end
Roller end
Roller end
Roller end
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
D
D
1
2
3
1
2
3
1
2
3
1
2
3
Pae 8

Step 5
å Fasten the UPRIGHTS (C) to the TOP (E2). Tihten four
HIDDEN CAMS.
Finished ede
Start Tighten
Arrow
Minimum
190 derees
Maximum
210 derees
Arrow
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Lon finished ede
Surface
with holes
C
C
E2
Part (E2). Another
sturdier, easier,
friendlier component!
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

Step
å Fasten the SHELF (G2) to the UPRIGHTS (C). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 6
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
Surface with
TWIST-LOCK
®
FASTENERS
Finished ede
C
C
G2
Pae 10