Sauder 427470 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Share your journey! Lot # 546087 05/27/20
Purchased: __________________
English pg 1-24
Français pg 25-28
Español pg 29-32
Library
Model 427470
Treat yourshelf.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-24
25-28
29-32
33-34
35
427470 www.sauder.com/servicePage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A UPPER END (2)
B LOWER END (2)
CUPPER RIGHT FRONT/LEFT
REAR LEG (2)
DUPPER LEFT FRONT/RIGHT
REAR LEG (2)
ELOWER RIGHT FRONT/LEFT
REAR LEG (2)
FLOWER LEFT FRONT/RIGHT
REAR LEG (2)
G SKIRT (2)
H UPPER TOP (1)
J LOWER TOP (1)
K BOTTOM (1)
L UPPER ADJUSTABLE SHELF (2)
M LOWER ADJUSTABLE SHELF (1)
N RIGHT DOOR MOLDING (1)
O LEFT DOOR MOLDING (1)
P RIGHT DOOR (1)
Q LEFT DOOR (1)
R LARGE BACK (1)
S SMALL BACK (1)
427470www.sauder.com/service Page 3
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
S
C
D
A
B
E
F
L
G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427470 www.sauder.com/servicePage 4
TACK GLIDE - 4
22E HIDDEN CAM - 36 1F CAM DOWEL - 12 2F CAM SCREW - 24 8F
WOOD DOWEL - 4
15F ANGLE BRACKET - 6
27G 14H HINGE - 4 DOOR STOP - 2
4I
PULL - 2
149K
WASHER - 4
9I TAPE CARD - 1
4M NAIL - 60 1N
FURNITURE TIPPING
RESTRAINT KIT - 1
97
CAM COVER - 36
75P METAL PIN - 12 1R RUBBER SLEEVE - 12 2R
BLACK 9/16" LARGE HEAD SCREW - 12
1S BROWN 7/16" LARGE HEAD SCREW - 4 6S
BLACK 1/2" FLAT HEAD SCREW - 8
11S 15S SILVER 5/8" MACHINE SCREW - 4
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM DOWEL
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
427470www.sauder.com/service Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the UPPER ENDS (A).
å Turn twelve CAM SCREWS (8F) into the UPPER LEGS (C and D).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
427470 www.sauder.com/servicePage 6
A
C
D
1
8F
(16 used)
1F
Arrow
1F
Arrow
1F
Arrow
(12 used)
A
D
C

å Fasten one set of UPPER LEGS (C and D) to one UPPER
END (A). Tighten six HIDDEN CAMS.
å Repeat this step for the other UPPER END (A) and
UPPER LEGS (C and D).
Step 2
427470www.sauder.com/service Page 7
A
C
D
1
Surface with
HIDDEN CAMS
These surfaces
should be even.
Short edge with
HIDDEN CAMS
End with hole
End with hole
Remember:
Righty tighty.
Lefty loosey.

å Insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM in the UPPER ENDS (A).
å Fasten the UPPER TOP (H) to the UPPER ENDS (A).
Tighten four HIDDEN CAMS.
Step 3
427470 www.sauder.com/servicePage 8
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
1
Metal end
2F
(4 used)
HA
Surface with
HIDDEN CAMS
A
Surface without
HIDDEN CAMS
These holes must be here.

å Fasten the LOWER TOP (J) to the UPPER LEGS (C and D).
Use four BLACK 2-1/4" FLAT HEAD SCREWS (26S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Insert two DOOR STOPS (4I) into the holes in the
LOWER TOP (J).
Step 4
427470www.sauder.com/service Page 9
C
D
D
C
J
4I
Surface with more holes
These edges must be even.
BLACK 2-1/4" FLAT HEAD SCREW
(4 used in this step)
26S

å Push sixteen HIDDEN CAMS (1F) into the LOWER ENDS (B).
å Turn twelve CAM SCREWS (8F) into the LOWER LEGS (E and F).
å Insert four WOOD DOWELS (15F) into the LEGS (E and F).
Step 5
427470 www.sauder.com/servicePage 10
B
E
F
1
15F
8F
(16 used)
1F
Arrow
1F
Arrow
1F
Arrow
(12 used)
F
E
B