Sauder Edge Water 419401 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-34
Français pg 35-39
Español pg 40-44
Lot # 374148 08/18/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Computer Desk with Hutch
Edge Water Collection | 419401
For all your
newfangled gadgetry.

Table of Contents Assembly Tools Required
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
Skip the power trip.
This time.
2-3
4-5
6-34
35-39
40-44
45-46
47
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
419401 www.sauder.com/servicesPage 2
Now you know
our ABCs.
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G MODESTY PANEL (1)
H SHELF (1)
I LARGE BACK (1)
J BACK (1)
K DOOR (1)
L ADJUSTABLE SHELF (1)
M LEG (3)
N HUTCH RIGHT END (1)
O HUTCH LEFT END (1)
P HUTCH UPRIGHT (1)
Q HUTCH TOP (1)
R HUTCH SHELF (1)
S BACK SKIRT (1)
T DIVIDER (3)
U DRAWER FRONT (1)
V LARGE DRAWER FRONT (1)
W FRONT MOLDING (1)
X SHELF MOLDING (1)
Y TOP MOLDING (1)
Z TOP FRONT MOLDING (1)
AA TOP LEFT MOLDING (1)
BB TOP RIGHT MOLDING (1)
CC FOOT (3)
D102 LARGE DRAWER SIDE (2)
D216 DRAWER SIDE (2)
D484 DRAWER BOX FRONT (2)
D485 LARGE DRAWER BOX FRONT (2)
D713 DRAWER BOTTOM (2)
Short Screwdriver

Part Identification
419401www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
D102
D216
D484
D485
D713
M
M
TT
BB
AA
D102
D216 D484
D485
D713
CC
CC
CC

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419401 www.sauder.com/servicesPage 4
FILE GLIDE - 2
3B FILE ROD - 2
8B
40CA CABINET RIGHT - 2 40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
SAFETY BRACKET - 1
1G ANGLE BRACKET - 2
5G
10F TWIST-LOCK®
FASTENER - 2
MOLDING
CONNECTOR - 2
17F
METAL PIN - 15
1R
CAM SCREW - 11
8F
DOOR STOP - 1
4I
NAIL - 61
1N
HIDDEN CAM - 42
1F CAM DOWEL - 31 2F
CAM COVER - 20
13P RUBBER SLEEVE - 4 2R
13H HINGE - 2 18K BACKPLATE - 1
17K KNOB - 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419401www.sauder.com/services Page 5
BLACK 1-1/8" MACHINE SCREW - 3
21S
BLACK 9/16" LARGE HEAD SCREW - 8
1S
SILVER 1-1/8" FLAT HEAD SCREW - 2
10S
BLACK 1-1/4" FLAT HEAD SCREW - 9
7S
BLACK 7/8" LARGE HEAD SCREW - 6
17S
BLACK 1-7/8" FLAT HEAD SCREW - 8
2S
3S GOLD 5/16" FLAT HEAD SCREW - 16
BLACK 1/2" FLAT HEAD SCREW - 4
11S
30S BLACK 1-9/16" FLAT HEAD SCREW - 16
16S BLACK 1-7/8" PAN HEAD SCREW - 3

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
419401 www.sauder.com/servicesPage 6
Do not tighten the TWIST-LOCK® FASTENERS in this step.
10F
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (10F) into the large holes in the
MODESTY PANEL (G).
G

Step 2
419401www.sauder.com/services Page 7
å Push forty-two HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C
and D), BOTTOM (F), MODESTY PANEL (G), SHELF (H), HUTCH ENDS (N
and O), HUTCH UPRIGHT (P), HUTCH SHELF (R), and BACK SKIRT (S).
Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM,
except for the side edges of the ENDS (A and B), LEFT UPRIGHT (D),
and SHELF (H).
(42 used)
(31 used)
Arrow
1F
2F
Do not tighten the HIDDEN
CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1F
Arrow
G
S
O
N
P
A
B
D
H
R
F
C
Do not insert
CAM DOWELS
into these edges.

Step 3
419401 www.sauder.com/servicesPage 8
8F
å Turn eleven CAM SCREWS (8F) into the LEGS (M) and
SHELF MOLDING (X).
(11 used)
M
M
M
X
Remember:
Righty tighty.
Lefty loosey.

Step 4
419401www.sauder.com/services Page 9
å Tap two MOLDING CONNECTORS (17F) into the notches
in the TOP MOLDINGS (Z, AA, and BB).
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.
17F
17F
ZBB
AA

å Fasten the TOP MOLDINGS (Z, AA, and BB) to the
HUTCH TOP (Q). Use nine BLACK 1-1/4" FLAT
HEAD SCREWS (7S).
å NOTE: Do not overtighten the SCREWS into the TOP.
Step 5
419401 www.sauder.com/servicesPage 10
Z
BB
AA
Q
Surface
with holes
Unfinished edge
BLACK 1-1/4" FLAT HEAD SCREW
(9 used in this step)
7S
Do not overtighten
the SCREWS (7S).