Sauder Hythe 5426439 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Sit and surf.
Hythe Wall Mounted Desk
Model 5426439

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-18
19-21
22-24
25-26
27
Straiht Ede Screwdriver
Pae 2
Electric drill with 5/16" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A DESK TOP (1)
B LEFT END (1)
C RIGHT END (1)
D UPRIGHT (1)
E BACK (1)
F BOTTOM (1)
G BRACE (6)
H SHELF (2)
J DOOR (1)
K UPPER FRAME (2)
L LOWER FRAME (2)
A
B
C
D
E
F
G
G
G
GG
G
H
H
J
K
KL
L
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 6
2
1/2" HEX HEAD SCREW - 8
13
HIDDEN CAM - 6
1WOOD DOWEL - 12
3
1-9/16" PAN HEAD SCREW - 6
11
1/2" FLAT HEAD SCREW - 8
14
WALL ANCHOR - 2
8
2" PAN HEAD SCREW - 2
10
1-3/16" HEX HEAD SCREW - 24
12
6PULL - 1
UPPER GUIDE - 2
4LOWER GUIDE - 2 5
APPLIQUE CARD - 1
7L-WRENCH - 1
9
Pae 4
1-15/16" HEX HEAD SCREW - 4
16
15 38" MACHINE SCREW  2

Hardware Usae Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
ently tap the CAM DOWEL
until the shoulder is aainst
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
ede of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tihten the HIDDEN CAM.
Pae 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push six HIDDEN CAMS (1) into the ENDS (B and C) and
UPRIGHT (D).
å Turn six CAM SCREWS (2) into the DESK TOP (A).
B
C
D
2
A
Arrow
1
Pae 6

å Insert six WOOD DOWELS (3) into the DESK TOP (A).
å Fasten the ENDS (B and C) and UPRIGHT (D) to the
DESK TOP (A). Tihten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the DESK TOP
insert into the ENDS and UPRIGHT.
Step 2
B
C
D
A
3
3
3Groove
Groove
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Pae 7

å Slide the BACK (E) into the rooves of the ENDS (B and C)
and DESK TOP (A).
Step 3
Finished surface
E
B
C
A
Pae 8

å Insert six WOOD DOWELS (3) into the ENDS (B and C)
and UPRIGHT (D).
å Fasten the BOTTOM (F) to the ENDS (B and C) and
UPRIGHT (D). Use six 1-9/16" PAN HEAD SCREWS (11).
å NOTE: Be sure the WOOD DOWELS in the ENDS and
UPRIGHTS insert into the BOTTOM.
Step 4
B
C
D
F
Groove
3
3
3
1-9/16" PAN HEAD SCREW
(6 used in this step)
11
Pae 9

å Fasten two BRACES (G) to the BOTTOM (F). Tihten four
1-3/16" HEX HEAD SCREWS (12) usin the L-WRENCH (9).
Step 5
F
G
G
9
1-3/16" HEX HEAD SCREW
(4 used in this step)
12
Pae 10