Sauder Palladia 413998 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-20
Français...............Pages 20-22
Espanol.............Páginas 23-26
Lot #: 347564 10 / 16 / 12
Date Purchased: ____________________
413998
Queen Platform Bed
Palladia Collection

ASSEMBLY TOOLS REQUIRED
Tip Shown Actual Size
No. 2 Phillips Screwdriver
Hammer
Short Phillips Screwdriver (provided)
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-19
Français..............................20-22
Espanol...............................23-26
Warranty...................................27
Page 2 www.sauder.com/services 413998

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A HEAD END 1
B FOOT END 1
C UPPER LONG END 2
D LOWER LONG END 2
ELARGE CENTER
UPRIGHT 2
F HEAD UPRIGHT 2
G SLAT 5
H FOOT UPRIGHT 2
I DRAWER UPRIGHT 2
J RIGHT LONG TOP 1
K LEFT LONG TOP 1
L SHORT TOP 1
M DRAWER BOTTOM 4
N LARGE PANEL 2
O SMALL PANEL 2
P RIGHT DRAWER FRONT 2
Q LEFT DRAWER FRONT 2
R RIGHT DRAWER SIDE 4
S LEFT DRAWER SIDE 4
T DRAWER BACK 4
U DRAWER BRACE 4
G
G
G
G
G
J
K
L
A
B
C
C
D
D
E
E
F
F H
H
I
I
M
M
N
N
O
O
P
Q
R
RS
S
T
TU
U
M
M
P
Q
R
R
S
S
T
T
U
U
Page 3
www.sauder.com/services413998

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
DRAWER FRONT BRACKET - 4
Z
WEXTENSION SLIDE - 8 VEXTENSION RAIL - 8
(EXTENSION SET SHOWN SEPARATED)
GOLD 5/16" FLAT HEAD SCREW - 32
II
BLACK 1-7/8" FLAT HEAD SCREW - 34
CC
HIDDEN CAM - 28
X
CAM DOWEL - 28
Y
BLACK 9/16" LARGE HEAD SCREW - 16
GG
BLACK 1-9/16" FLAT HEAD SCREW - 20
DD
PROPEL NUT - 4
BB
SILVER 1/2" MACHINE SCREW - 8
HH
KNOB - 8
AA
Page 4 www.sauder.com/services 413998
BLACK 1-1/8" PAN HEAD SCREW - 24
FF

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push twenty-eight HIDDEN CAMS (X) into the ENDS (A and B), UPRIGHTS (E, F, H, and I) and BRACES (U). Then, insert the
metal end of a CAM DOWEL (Y) into each HIDDEN CAM.
Do not tighten the HIDDEN CAMS in this step.
Arrow
(28 used)
(28 used)
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
X
X
Y
Y
A
B
F
F
H
H
I
I
E
E
U
Page 5
www.sauder.com/services413998

Separate the EXTENSION SLIDES (W) from the EXTENSION RAILS (V) as shown in the upper diagram. Be prepared, the parts
are greasy.
Fasten four EXTENSION RAILS (V) to the DRAWER UPRIGHTS (I). Use eight GOLD 5/16" FLAT HEAD SCREWS (II).
NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the UPRIGHTS. Turn a SCREW into this
hole.
Push the black lever in and pull the SLIDE from the RAIL.
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
II
Open end
Open end
2
2
S
t
e
p
V
V
V
V
V
W
I
I
Surface with
HIDDEN CAMS Surface without
HIDDEN CAMS
Finished edge
Finished edge
Page 6 www.sauder.com/services 413998

Fasten four EXTENSION RAILS (V) to the UPRIGHTS (F and H). Use eight GOLD 5/16" FLAT HEAD SCREWS (II).
NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the UPRIGHTS. Turn a SCREW into this
hole.
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
II
3
3
S
t
e
p
V
V
V
V
Open end
Open end
Open end
Open end
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
F
F
H
H
Page 7
www.sauder.com/services413998

Use a hammer to drive four PROPEL NUTS (BB) into the holes in the HEAD END (A).
Fasten the HEAD END (A) to the LARGE CENTER UPRIGHTS (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (CC).
4
4
S
t
e
p
Surface with
HIDDEN CAMS
A
A
BB
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
CC
E
E
Surface without
HIDDEN CAMS
Finished edge
These holes
must be here.
Page 8 www.sauder.com/services 413998

Fasten the HEAD UPRIGHTS (F) to the LARGE CENTER UPRIGHTS (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (CC).
Fasten the DRAWER UPRIGHTS (I) to the LARGE CENTER UPRIGHTS (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (CC).
5
5
S
t
e
p
BLACK 1-7/8" FLAT HEAD SCREW
(8 used in this step)
CC
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
The EXTENSION RAILS
should be closer to the floor.
F
FI
I
E
E
Page 9
www.sauder.com/services413998
The EXTENSION RAILS
should be closer to the floor.

Fasten the FOOT UPRIGHTS (H) to the LARGE CENTER UPRIGHTS (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (CC).
6
6
S
t
e
p
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
CC
H
H
E
E
Page 10 www.sauder.com/services 413998
The EXTENSION RAIL
should be closer to the floor.
The EXTENSION RAIL
should be closer to the floor.