Sauder Harbor View 415802 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 355540 08 / 26 / 13
Date Purchased: ____________________
415802
Multi-Purpose Stand
Harbor View Collection
English.................... Page 1-21
Français...............Pages 22-24
Espanol.............Páginas 25-27

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
Page 2 www.sauder.com/services 415802
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-21
Français..............................22-24
Espanol...............................25-27
Safety .................................28-30
Warranty...................................31

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D BOTTOM 1
D24 RIGHT DRAWER SIDE 1
D25 LEFT DRAWER SIDE 1
D70 DRAWER BACK 1
D719 DRAWER BOTTOM 1
E SHELF 1
F BACK 1
G LONG DIVIDER 1
H SHORT DIVIDER 2
I RIGHT FRONT LEG 1
J LEFT FRONT LEG 1
K BACK LEG 2
L SKIRT 1
M DRAWER FRONT 1
N FRONT TOP MOLDING 1
O RIGHT TOP MOLDING 1
P LEFT TOP MOLDING 1
Q SHELF MOLDING 1
A
B
C
D
E
F
G
H
H
I
J
K
K
L
M
NP
Q
Page 3
www.sauder.com/services415802
O
D719
D24
D25
D70

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
NAIL - 33
1N
PULL -1
98K
SILVER 5/8" MACHINE SCREW - 2
15S
SILVER 1-1/8" FLAT HEAD SCREW - 6
10S
MOLDING CONNECTOR - 2
19F
HIDDEN CAM - 20
1F
CAM SCREW - 8
8F
CAM DOWEL -12
2F
LONG METAL PIN - 2
3R
GOLD 5/16" FLAT HEAD SCREW - 8
3S
ANGLE BRACKET - 3
5G
BLACK 9/16" LARGE HEAD SCREW - 6
1S
CAM COVER - 14
12P
TACK GLIDE - 4
12E
SLIDE CAM - 2
10A
BLACK 2-1/4" FLAT HEAD SCREW - 6
26S
BLACK 1-9/16" FLAT HEAD SCREW - 4
30S
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1
35GD DRAWER LEFT - 1
Page 4 www.sauder.com/services 415802

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), BOTTOM (D), and SHELF (E). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM, except the long edges of the ENDS (A and B) and SHELF (E).
Page 5
www.sauder.com/services415802
Do not tighten the HIDDEN CAMS in this step.
Arrow
(12 used)
(20 used)
Arrow
1F
1F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
E
D
Do not insert CAM
DOWELS into these edges.
Do not insert CAM
DOWELS into this edge.

Turn eight CAM SCREWS (8F) into the LEGS (I and J) and SHELF MOLDING (Q).
2
2
S
t
e
p
Page 6 www.sauder.com/services 415802
8F
QI
J

Fasten the LEGS (I and J) to the ENDS (A and B). Tighten six HIDDEN CAMS.
Fasten the BACK LEGS (K) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S).
NOTE: Be sure the center holes in the LEGS (K) line up before fastening the LEGS to the ENDS (A and B).
3
3
S
t
e
p
Page 7
www.sauder.com/services415802
K
K
I
J
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
BLACK 2 1/4" FLAT HEAD SCREW
(6 used in this step)
26S
These edges
should be even.
These edges
should be even.
Line up the center
holes in the LEGS
before fastening
to the ENDS.

4
4
S
t
e
p
Page 8 www.sauder.com/services 415802
Roller end
Fasten a CABINET RIGHT (35GA) to the RIGHT END (A) and a CABINET LEFT (35GB) to the LEFT END (B). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
GOLD 5/16" FLAT HEAD SCREW
(4 used for the CABINET RIGHT and LEFT)
3S
3
2
1
Roller end
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
I
J
3
2
1

5
5
S
t
e
p
Page 9
www.sauder.com/services415802
Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (N, O, and P).
Flat end Flat end
Use your hammer to tap the MOLDING CONNECTOR (19F) into the notches in the MOLDINGS.
19F 19F
N
O
P

Fasten the MOLDINGS (N, O, and P) to the TOP (C). Use six SILVER 1-1/8" FLAT HEAD SCREWS (10S).
6
6
S
t
e
p
Page 10 www.sauder.com/services 415802
N
O
P
C
SILVER 1-1/8" FLAT HEAD SCREW
(6 used in this step)
10S
Flat edge
Surface with holes