Sauder Cannery Bridge 418326 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-31
Français pg 32-35
Español pg 36-40
Lot # 366853 12/03/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Computer Desk
Cannery Bridge Collection | Model 418326
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Sit and surf.

Table of Contents Assembly Tools Required
2-3
4-5
6-31
32-35
36-40
41-42
43
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
418326 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (2)
G MODESTY PANEL (1)
H BACK (2)
J DOOR (1)
K ADJUSTABLE SHELF (1)
L FRONT LEG (4)
M BACK LEG (2)
N DRAWER FRONT (1)
O FILE DRAWER FRONT (1)
P PENCIL DRAWER FRONT (1)
Q BOTTOM MOLDING (2)
R END MOLDING (2)
S EXTENSION BLOCK (2)
EE DRAWER BRACE (1)
B27 PENCIL DRAWER BOTTOM (1)
D26 DRAWER RIGHT SIDE (1)
D27 DRAWER LEFT SIDE (1)
D28 FILE DRAWER RIGHT SIDE (1)
D29 FILE DRAWER LEFT SIDE (1)
D150 DRAWER BACK (1)
D151 FILE DRAWER BACK (1)
D266 PENCIL DRAWER RIGHT
SIDE (1)
D267 PENCIL DRAWER LEFT SIDE (1)
D468 PENCIL DRAWER BACK (1)
D469 PENCIL DRAWER BOX
FRONT (1)
D702 DRAWER BOTTOM (1)
D954 FILE DRAWER BOTTOM (1)

Part Identification Now you know
our ABCs.
418326www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
EE
J
K
L
M
N
O
P
Q
R
S
H
M
S
L
L
L
F
Q
R
D150
D469
D29
D954
D151 D28
D702
D27
D26
D266
D267
B27
D468

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
45BA CABINET RIGHT - 1 45BD DRAWER LEFT - 1 45BC DRAWER RIGHT - 1 45BB CABINET LEFT - 1
40CA CABINET RIGHT - 2 40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
FILE GLIDE - 2
15B
418326 www.sauder.com/servicesPage 4
METAL PIN - 4
1R
10A SLIDE CAM - 4
CAM SCREW - 12
8F 14H HINGE - 2 DOOR STOP - 1 4I
WOOD DOWEL - 4
15F
NAIL - 30
1N
HIDDEN CAM - 30
1F CAM DOWEL - 18 2F
PULL - 3
101K RUBBER SLEEVE - 4
2R
CORD CLIP - 1
31P
FILE ROD - 2
7B

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" PAN HEAD SCREW - 4
9S
418326www.sauder.com/services Page 5
15S SILVER 5/8" MACHINE SCREW - 6 BLACK 7/8" LARGE HEAD SCREW - 2 17S
BLACK 1-7/8" FLAT HEAD SCREW - 4
2S 3S GOLD 5/16" FLAT HEAD SCREW - 24
100S BLACK 2-3/4" FLAT HEAD SCREW - 6
BLACK 1/2" FLAT HEAD SCREW - 4
11S
BLACK 9/16" FLAT HEAD SCREW - 4
32S30S BLACK 1-9/16" FLAT HEAD SCREW - 14

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), BOTTOMS (F), and MODESTY
PANEL (G). Then, insert the metal end of eighteen CAM
DOWELS (2F) into each HIDDEN CAM, except the long
edges of the ENDS (A and B) and UPRIGHTS (C and D).
418326 www.sauder.com/servicesPage 6
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
B
C
D
F
G
F
Arrow
1F
2F
Do not insert
CAM DOWELS
into these edges.
(30 used)
(18 used)
Arrow
1F
2F

StepStep 2
å Turn twelve CAM SCREWS (8F) into the FRONT LEGS (L).
å NOTE: Position the LEGS exactly as shown.
å NOTE: Use the exact holes shown.
å Insert four WOOD DOWELS (15F) into the holes in the
FRONT LEGS (L).
418326www.sauder.com/services Page 7
8F (12 used)
Remember:
Righty tighty.
Lefty loosey.
L
L
L
L
15F
These holes are
closer to these edges.
These holes are
closer to these edges.
3 used in each leg

StepStep 3
418326 www.sauder.com/servicesPage 8
å Fasten the ENDS (A and B) and UPRIGHTS (C and D) to
the FRONT LEGS (L). Tighten twelve HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the FRONT LEGS
insert into the holes in the ENDS and UPRIGHTS.
1
2
A
B
C
D
L
L
L
L
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces
should be even.
These surfaces
should be even.
These ends
should be even.
These ends
should be even.
These surfaces
should be even.
These surfaces
should be even.
These ends
should be even.

StepStep 4
418326www.sauder.com/services Page 9
å Flip the ENDS (A and B) over.
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å Slide the END MOLDINGS (R) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
These edges
should be even.
These edges
should be even.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
A
B
Shoulder
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
R
R

Step
å Fasten the BACK LEGS (M) to the ENDS (A and B). Use
six BLACK 2-3/4" FLAT HEAD SCREWS (100S).
Step 5
418326 www.sauder.com/servicesPage 10
A
B
M
M
BLACK 2-3/4" FLAT HEAD SCREW
(6 used in this step)
100S

StepStep 6
418326www.sauder.com/services Page 11
45BB
45BB
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
45BA
45BA
1
3
2
1
3
2
4
4
Roller end
Roller end
A
C
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
L
L
å Flip the RIGHT END (A) over.
å Fasten the CABINET RIGHT (45BA) to the RIGHT END (A)
and CABINET LEFT (45BB) to the RIGHT UPRIGHT (C).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #4.

StepStep 7
418326 www.sauder.com/servicesPage 12
A
C
å Fasten the CABINET RIGHT (40CA) to the RIGHT END (A)
and CABINET LEFT (40CB) to the RIGHT UPRIGHT (C).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #3.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
1
2
3
4
1
2
3
4
Roller end
Roller end
L
L

StepStep 8
418326www.sauder.com/services Page 13
C
D
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
GOLD 5/16" FLAT HEAD SCREW
(4 used for the RAILS)
3S
1
2
3
4
1
2
34
Roller end
Roller end
S
S
Finished
surface
Finished edge
Finished edge
BLACK 1-1/8" PAN HEAD SCREW
(4 used for the EXTENSION BLOCKS)
9S
L
L
å Flip the UPRIGHTS (C and D) over.
å Fasten the EXTENSION BLOCKS (S) to the UPRIGHTS (C and D).
Use four BLACK 1-1/8" PAN HEAD SCREWS (9S).
å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB)
to the EXTENSION BLOCKS (S). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) through holes #1 and #3.

Step
å Fasten the TOP (E) to the MODESTY PANEL (G). Tighten
two HIDDEN CAMS.
Step 9
418326 www.sauder.com/servicesPage 14
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
G
E
Surface with
HIDDEN CAMS
Surface
with holes
This hole must be here.
Now might be a
good time to refresh
your drink.

StepStep 10
å Fasten the UPRIGHTS (C and D) to the TOP (E). Tighten four
HIDDEN CAMS.
å Fasten the UPRIGHTS (C and D) to the MODESTY PANEL (G).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
418326www.sauder.com/services Page 15
Arrow
Minimum
190 degrees
Maximum
210 degrees
E
C
D
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
G
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step
å Push the DOOR STOP (4I) into the hole in the TOP (E).
å Fasten the BOTTOMS (F) to the UPRIGHTS (C and D).
Tighten four HIDDEN CAMS.
Step 11
418326 www.sauder.com/servicesPage 16
Arrow
Minimum
190 degrees
Maximum
210 degrees
C
D
F
Surface
with
HIDDEN
CAMS
F
Surface
with
HIDDEN
CAMS
Notched edge
Notched edge
4I
E

StepStep 12
418326www.sauder.com/services Page 17
å Slide the BOTTOM MOLDINGS (Q) onto the notched
edges of the BOTTOMS (F).
å *U.S. Patent No. 5,499,886
Notched edge
F
F
Q
Q
Slide the BOTTOM
MOLDINGS (Q) onto
the notched edges.

Step
å Fasten the ENDS (A and B) to the TOP (E) and
BOTTOMS (F). Tighten eight HIDDEN CAMS.
Step 13
418326 www.sauder.com/servicesPage 18
Arrow
Minimum
190 degrees
Maximum
210 degrees
E
F
F
B
A
Surface without
HIDDEN CAMS
Surface
with
HIDDEN
CAMS

StepStep 14
418326www.sauder.com/services Page 19
å Carefully turn your unit over onto its front edges. Lay the
BACKS (H) over your unit.
å Fasten the BACKS (H) to your unit using the NAILS (1N).
å NOTE: Be sure to tap NAILS into the holes that line up
over the BOTTOMS (F).
å NOTE: Perforations have been provided for access
through the BACKS. Carefully cut out the holes needed.
å Turn the CORD CLIP (31P) into the hole in the TOP (E).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(30 used in this step)
1N
Ffinished
surface
H
Edge without holes
These holes must line up
over the BOTTOMS (F).
Ffinished
surface
H
Edge without holes
31P
EDo not put NAILS
in these two holes.
The edge of the BACK should be
even with the edge of the UPRIGHT.
These holes should
line up over the LEG.
These holes should
line up over the LEG.

StepStep 15
418326 www.sauder.com/servicesPage 20
å Fasten two HINGES (14H) to the DOOR (J). Use four
BLACK 1/2" FLAT HEAD SCREWS (11S).
14H
BLACK 1/2" FLAT HEAD SCREW
(4 used in this step)
11S
J
Surface with
more holes