Sauder Harbor View 417586 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
For all your
newfangled gadgetry.
Lot # 535570 11/04/19
Purchased: __________________
English pg 1-56
Français pg 57-64
Español pg 65-72
Corner Computer Desk
Harbor View Collection | Model 417586

Part Identification
Hardware Identification
Assembly Steps
Troubleshooting
Français
Español
Safety
Warranty
2-3
4-5
6-55
56
57-64
65-72
73-74
75
Assembly Tools RequiredTable of Contents
Now you know
our ABCs.
Part Identification
Electric drill with 1/8" bit
(ONLY in indicated step)
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Scissors
Masking Tape
A DOOR RIGHT END (1)
B DOOR LEFT END (1)
C DRAWER RIGHT END (1)
D DRAWER LEFT END (1)
D24 SMALL RIGHT DRAWER SIDE (2)
D25 SMALL LEFT DRAWER SIDE (2)
D28 RIGHT DRAWER SIDE (1)
D29 LEFT DRAWER SIDE (1)
D78 DRAWER BACK (1)
D109 SMALL DRAWER BACK (2)
D707 DRAWER BOTTOM (1)
D716 SMALL DRAWER BOTTOM (2)
E RIGHT UPRIGHT (1)
F LEFT UPRIGHT (1)
G3 TOP (1)
H3 SMALL TOP (1)
I MODESTY PANEL (2)
J BOTTOM (1)
K BACK (2)
L BRACE (2)
M DOOR (1)
N DRAWER FRONT (1)
O SMALL DRAWER FRONT (2)
P ADJUSTABLE SHELF (1)
Q2 KEYBOARD UPRIGHT (2)
U KEYBOARD SHELF (1)
X BASE (2)
AA RIGHT MOLDING (1)
BB LEFT MOLDING (1)
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
417586 www.sauder.com/servicePage 2

Part Identification
A
BC
D
E
F
G3
H3
I
J
K
L
M
Q2
U
X
AA
BB
I
K
Q2
X
L
D716 D707
D29
D28
D78
D109D25
D24
ON
D716
D109D25
D24
O
P
417586www.sauder.com/service Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
GG NUMBERED RIGHT
CABINET RAIL - 1 HH NUMBERED LEFT CABINET RAIL - 1 JJ NUMBERED LEFT DRAWER SLIDE - 1
II NUMBERED RIGHT
DRAWER SLIDE - 1
FILE ROD - 2
8B
35DA CABINET RIGHT - 2 35DB CABINET LEFT - 2 35DC DRAWER RIGHT - 2 35DD DRAWER LEFT - 2
TIE PLATE - 2
41G
HIDDEN CAM - 18
1F
CAM DOWEL - 18
2F HIDDEN
CONNECTOR - 4
9F
13H HINGE - 2
ANGLE
BRACKET - 10
5G
10A SLIDE CAM - 6 FILE GLIDE - 2
15B
KNOB - 1
5K PULL - 3 98K
40AW CABINET RIGHT - 1 40AX CABINET LEFT - 1 40AY DRAWER RIGHT - 1 40AZ DRAWER LEFT - 1
METAL
BRACKET - 4
2G
417586 www.sauder.com/servicePage 4

Hardware Identification
FELT DISC CARD - 1
1M
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" PAN HEAD SCREW - 10
9S
BLACK 9/16" LARGE HEAD SCREW - 36
1S
CONNECTOR SCREW - 4
8S
BLACK 1-7/8" FLAT HEAD SCREW - 6
2S
18S BROWN 1" FLAT HEAD SCREW - 4
3S GOLD 5/16" FLAT HEAD SCREW - 28
BLACK 1/2" FLAT HEAD SCREW - 4
11S
GOLD 1" MACHINE SCREW - 1
50S
15S SILVER 5/8" MACHINE SCREW - 6
GROMMET - 1
10P
GROMMET CAP - 1
1P
CORD CLIP - 9
4P METAL PIN - 8 1R
NAIL - 30
1N
RUBBER
SLEEVE - 4
2R
30S BLACK 1-9/16" FLAT HEAD SCREW - 12
HIDDEN WIRELESS Qi COMPATIBLE
CHARGER by EGGTRONIC - Item 425905
(sold separately)
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
417586www.sauder.com/service Page 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Fasten a DRAWER RIGHT (40AY) and a DRAWER LEFT (40AZ)
to the KEYBOARD SHELF (U). Use four BROWN 1" FLAT
HEAD SCREWS (18S).
å Turn a CORD CLIP (4P) into the KEYBOARD SHELF (U).
å NOTE: The CORD CLIP is used to hold your keyboard cord
against the TOP.
4P
Roller end
Roller end
U
Finished edge
BROWN 1" FLAT HEAD SCREW
(4 used in this step)
18S
Finished surface
4 0 A Z
40AZ
4 0 AY
40AY
417586 www.sauder.com/servicePage 6

StepStep 2
With the palm of
your hand, tap
the DRAWER
BOTTOM down
into the groove.
VIEW THE T-LOCK BOX VIDEO
å Fasten the DRAWER BACK (D109) to the
DRAWER SIDES (D24 and D25). Use four
BLACK 1-9/16" FLAT HEAD SCREWS (30S).
å NOTE: Be sure the DRAWER BOTTOM (D716) inserts into
the groove of the DRAWER BACK (D109).
å Repeat this step for the other small drawer.
12
3
å Insert the DRAWER SIDES (D24 and D25) at an angle
into the slot at each end of the DRAWER FRONT (O).
å Slide the DRAWER BOTTOM (D716) into the grooves in the
DRAWER SIDES (D24 and D25) and DRAWER FRONT (O).
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Groove
30S
Start each screw a few turns before
completely tightening any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(8 used in this step)
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT groove.
O
D25 D25
D25
D24
D24
D24
O
D109
Unfinished
surface
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK groove.
D716
D716
417586www.sauder.com/service Page 7

Step
å Insert a SLIDE CAM (10A) into each DRAWER SIDE (D24 and D25).
å Fasten the DRAWER RIGHT (35DC) and DRAWER LEFT (35DD) to the DRAWER SIDES (D24 and D25). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
å Fasten a PULL (98K) to the DRAWER FRONT (N). Use two SILVER 5/8" MACHINE SCREWS (15S).
å Repeat this step for the other small drawer.
Step 3
3 5 D D
35DD
3 5 D C
35DC
1
3
2
1
3
2
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
D24
D25
98K
SILVER 5/8" MACHINE SCREW
(4 used for the PULLS)
15S
417586 www.sauder.com/servicePage 8
Screw head - turn CAM to line up holes in
the SLIDES with holes in DRAWER SIDES
10A
10A

StepStep 4 VIEW THE T-LOCK BOX VIDEO
å Fasten the DRAWER BACK (D78) to the DRAWER SIDES (D28 and D29). Use four
BLACK 1-9/16" FLAT HEAD SCREWS (30S).
å NOTE: Be sure the DRAWER BOTTOM (D707) inserts into the groove of the
DRAWER BACK (D78).
12
3
å Insert the DRAWER SIDES (D28 and D29) at an angle
into the slot at each end of the DRAWER FRONT (N).
å Slide the DRAWER BOTTOM (D707) into the grooves in the
DRAWER SIDES (D28 and D29) and DRAWER FRONT (N).
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Groove Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT groove.
D28
D29
D707
D707
D28
D29
D78
D29
NN
Unfinished
surface
With the palm of
your hand, tap the
DRAWER BOTTOM
down into the groove.
D28
Start each screw a few turns before
completely tightening any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(4 used in this step)
30S
417586www.sauder.com/service Page 9

Step
å Insert a SLIDE CAM (10A) into each DRAWER SIDE (D28 and D29).
å Fasten the SLIDES (II and JJ) to the DRAWER SIDES (D28 and D29).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #3.
å NOTE: The DRAWER SLIDES are marked "DRAWER RIGHT" and
"DRAWER LEFT" for easy identification.
å NOTE: The screw head in the CAM must be visible through the
slotted hole in the SLIDE.
å Fasten a PULL (98K) to the DRAWER FRONT (N). Use two
SILVER 5/8" MACHINE SCREWS (15S).
Step 5
II
JJ
Screw head - turn CAM to line up holes in
the SLIDES with holes in DRAWER SIDES
1
2
3
10A
10A
1
2
3
Roller end
Roller end
D28
D29
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
(4 screws per drawer)
98K
SILVER 5/8" MACHINE SCREW
(2 used for the PULLS)
15S
417586 www.sauder.com/servicePage 10