Sauder Cannery Bridge 424198 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-34
Français pg 35-39
Español pg 40-44
Lot # 522928 01/02/19
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Business or pleasure.
Works both ways.
L-Desk
Cannery Bridge Collection | Model 424198

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-34
35-39
40-44
45-46
47
424198 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END/UPRIGHT (2)
C RIGHT TOP (1)
D LEFT TOP (1)
D28 RIGHT DRAWER SIDE (1)
D29 LEFT DRAWER SIDE (1)
D151 DRAWER BACK (1)
D954 DRAWER BOTTOM (1)
E SHELF (2)
F RIGHT SHELF (1)
G RIGHT SUPPORT (1)
H LEFT SUPPORT (1)
J RIGHT MODESTY PANEL (1)
K LEFT MODESTY PANEL (1)
L LEFT FRONT LEG (1)
M FRONT UPRIGHT LEG (1)
N LEFT BACK LEG (1)
O BACK UPRIGHT LEG (1)
P RIGHT FRONT LEG (1)
Q RIGHT BACK LEG (1)
R RIGHT END MOLDING (2)
S END/UPRIGHT MOLDING (4)
T SHELF MOLDING (2)
U RIGHT TOP END MOLDING (1)
V LEFT TOP END MOLDING (1)
W RIGHT TOP MOLDING (1)
X LEFT TOP MOLDING (1)
Y SHORT TOP MOLDING (1)
Z BACK (1)
AA DRAWER FRONT (1)
A
B
B
C
D
E
E
F
G
HJ
K
L
M
N
O
P
Q
R
R
S
S
S
T
T
U
V
W
X
Y
Z
AA
D954
D151 D28
D29
424198www.sauder.com/services Page 3
S

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FILE ROD - 2
7B FILE GLIDE - 2 15B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 2
35MA EXTENSION SLIDE - 2 35MC
BLACK 9/16" LARGE HEAD SCREW - 12
1S
BLACK 1-1/4" FLAT HEAD SCREW - 8
7S
BLACK 7/8" MACHINE SCREW - 1
37S
3S GOLD 5/16" FLAT HEAD SCREW - 8
GROMMET - 2
7P
10A SLIDE CAM - 2
PLATE - 3
41G
BLACK 9/16" FLAT HEAD SCREW - 12
32S
CAM SCREW - 28
8F WOOD DOWEL - 13 15F
HIDDEN CAM - 32
1F CAM DOWEL - 4 2F
GLUE - 1
54M
BLACK 1-15/16" FLAT HEAD SCREW - 9
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
11F TWIST-LOCK®
FASTENER - 22
424198 www.sauder.com/servicesPage 4
KNOB - 1
178K APPLIQUE CARD - 7
91P

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
G
H
F
K
J
V
U
(22 used)
11F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push twenty-two SAUDER
TWIST-LOCK® FASTENERS (11F) into the large holes in
the SHELVES (E and F), SUPPORTS (G and H), MODESTY
PANELS (J and K) and END MOLDINGS (U and V).
Ex 2
11F
11F
424198www.sauder.com/services Page 5

Step 2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
å Push four HIDDEN CAMS (1F) into the RIGHT SHELF (F)
and LEGS (M and O). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
(4 used)
O
M
F
Some assembly
(and snacks) required.
424198 www.sauder.com/servicesPage 6

Step 3
A
Z
J
K
V
U
å Push twenty-eight HIDDEN CAMS (1F) into the remaining
holes of the ENDS (A and B), MODESTY PANELS (J and K),
END MOLDINGS (U and V) and BACK (Z).
1F
Arrow
(28 used)
Arrow
1F
1F
Arrow
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Bx 2
424198www.sauder.com/services Page 7

Step 4
L
P
Q
N
O
M
8F
8F
8F
å Turn twenty-eight CAM SCREWS (8F) into the LEGS (L, M,
N, O, P, and Q).
424198 www.sauder.com/servicesPage 8
(28 used)

Step 5
A
B
B
å Flip the ENDS (A and B) over. Turn twelve BLACK 9/16" FLAT HEAD SCREWS (32S) into the END/UPRIGHTS (B) and
RIGHT END (A) until the shoulders of the SCREWS rest on the surfaces of each part.
å NOTE: Do not overtighten the SCREWS.
å Slide the END/UPRIGHT MOLDINGS (S) onto the END/UPRIGHTS (B) and the RIGHT END MOLDINGS (R) onto the
RIGHT END (A). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS.
å NOTE: The MOLDINGS should be even on both edges of the ENDS.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on again.
BLACK 9/16" FLAT HEAD SCREW
(12 used in this step)
32S
Shoulder
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
BLACK 9/16" FLAT HEAD SCREW
32S
BLACK 9/16" FLAT HEAD SCREW
R
R
S
S
S
S
424198www.sauder.com/services Page 9

åFirst, fill the holes in the LEGS (L and N) 1/4 to 1/2 full
with GLUE (54M). Then, insert two WOOD DOWELS (15F)
into the holes as shown. Wipe away the excess GLUE.
åNow, fill the hole in the edge of a LEFT END/UPRIGHT (B)
1/4 to 1/2 full with GLUE (54M). Fasten the LEFT END/
UPRIGHT (B) and the LEFT TOP END MOLDING (V) to the
LEFT BACK LEG (N). Tighten three HIDDEN CAMS. Wipe
away the excess GLUE.
åLast, fill the hole in the opposite edge of the LEFT END/
UPRIGHT (B) 1/4 to 1/2 full with GLUE (54M). Fasten the LEFT
FRONT LEG (L) to the END/UPRIGHT (B) and the LEFT TOP
END MOLDING (V).
Tighten three HIDDEN CAMS. Wipe
away the excess GLUE.
Step 6
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
15F
15F
Surface with HIDDEN CAMS
Edge with
TWIST-LOCK®
FASTENERS
B
V
L
N
1
2
These surfaces
should be even.
Edge with hole
Edge with hole
424198 www.sauder.com/servicesPage 10

åFirst, fill the holes in the LEGS (M and O) 1/4 to 1/2 full with GLUE (54M).
Then, insert two WOOD DOWELS (15F) into the holes as shown. Wipe away
the excess GLUE.
åNOTE: Position the BACK UPRIGHT LEG (O) exactly as shown.
åNow, fill the hole in the edge of the LEFT END/UPRIGHT (B) 1/4 to 1/2 full with
GLUE (54M). Fasten the LEFT END/UPRIGHT (B) to the BACK UPRIGHT LEG (O).
Tighten two HIDDEN CAMS. Wipe away the excess GLUE.
åLast, fill the hole in the opposite edge of the LEFT END/UPRIGHT (B) 1/4 to
1/2 full with GLUE (54M). Fasten the FRONT UPRIGHT LEG (M) to the END/
UPRIGHT (B). Tighten two HIDDEN CAMS. Wipe away the excess GLUE.
Step 7
These surfaces
should be even.
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
15F
15F
Surface with HIDDEN CAMS
1
2
B
M
O
Edge with
CAM DOWEL
Edge with
CAM DOWEL
424198www.sauder.com/services Page 11

Step 8
åFirst, fill the holes in the LEGS (P and Q) 1/4 to 1/2 full with GLUE (54M). Then, insert
two WOOD DOWELS (15F) into the holes as shown. Wipe away the excess GLUE.
åNOTE: Position the RIGHT BACK LEG (Q) exactly as shown.
åNow, fill the hole in the edge of the RIGHT END (A) 1/4 to 1/2 full with GLUE (54M).
Fasten the RIGHT END (A) and the RIGHT TOP END MOLDING (U) to the RIGHT
BACK LEG (Q). Tighten four HIDDEN CAMS. Wipe away the excess GLUE.
åLast, fill the hole in the opposite edge of the RIGHT END (A) 1/4 to 1/2 full with
GLUE (54M). Fasten the RIGHT FRONT LEG (P) to the RIGHT END (A) and the
RIGHT TOP END MOLDING (U). Tighten four HIDDEN CAMS. Wipe away the
excess GLUE.
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
Surface with HIDDEN CAMS
Edge with
TWIST-LOCK®
FASTENERS
These surfaces
should be even.
Edge with hole
Edge with hole
A
P
Q
U
54M
15F
15F
1
2
424198 www.sauder.com/servicesPage 12

Step 9
Open end
å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (35MA) to the LEFT END/UPRIGHTS (B). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: Use the exact holes shown in the ENDS (B).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged
diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other hole
that lines up with the hole in the LEFT END/UPRIGHT. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWERS.
Open end
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
B
B
V
424198www.sauder.com/services Page 13
1
2
3
1
2
3

å Fasten the BACK (Z) to the LEFT BACK LEG (N). Tighten
two HIDDEN CAMS.
Step 10
N
Z
B
V
Surface with
HIDDEN
CAMS
1
2
424198 www.sauder.com/servicesPage 14

Step 11
å Fasten the SHELVES (E) to the LEFT END/UPRIGHT (B).
Tighten four TWIST-LOCK® FASTENERS.
How to use the SAUDER TWIST-LOCK® FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
B
E
E
Notched edge
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
424198www.sauder.com/services Page 15

Step 12
å Slide the SHELF MOLDINGS* (T) onto the notched edges
of the SHELVES (E).
å *U.S. Patent No. 5,499,886
The large
groove is
closer to
this edge.
E
E
T
T
424198 www.sauder.com/servicesPage 16

å Fasten the remaining LEFT END/UPRIGHT (B) assembly
to the BACK (Z) and SHELVES (E). Tighten two HIDDEN
CAMS and four
TWIST-LOCK® FASTENERS.
Step 13
E
E
B
Surface without holes
Z
424198www.sauder.com/services Page 17

å Fasten the LEFT MODESTY PANEL (K) to the LEFT
SUPPORT (H). Use two BLACK 1-15/16" FLAT HEAD
SCREWS (113S).
Step 14
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S
H
K
Surface with
TWIST-LOCK®
FASTENERS
Surface without TWIST-LOCK® FASTENERS
These edges must be even.
Rounded edge
424198 www.sauder.com/servicesPage 18

åFirst, fill the hole in the BACK UPRIGHT LEG (O) 1/4 to 1/2
full with GLUE (54M). Then, insert a WOOD DOWEL (15F)
into the hole as shown. Wipe away the excess GLUE.
åCarefully stand the LEFT END/UPRIGHT assembly
upright.
åNow, fill the hole in the short edge of the MODESTY
PANEL (K) 1/4 to 1/2 full with GLUE (54M). Be sure to fill
the third hole from the rounded edge.
åFasten the LEFT MODESTY PANEL (K) to the BACK
UPRIGHT LEG (O). Tighten three HIDDEN CAMS. Wipe
away the excess GLUE.
Step 15
K
O
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
15F
424198www.sauder.com/services Page 19
Rounded edge

å Fasten the RIGHT SHELF (F) to the RIGHT MODESTY
PANEL (J). Tighten two
TWIST-LOCK® FASTENERS.
Step 16
F
J
Surface with
TWIST-LOCK®
FASTENERS
Surface without TWIST-LOCK®
FASTENERS
Rounded edge
Don't worry. It isn't
Rome. This can be built
in a day.
424198 www.sauder.com/servicesPage 20