Sauder Cliff ord Place Credenza 429507 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-34
Français pg 35-39
Español pg 40-44
Lot # 557408 12/09/20
Purchased: __________________
Credenza
Cliord Place Collection | Model 429507
For things 'n such.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4-5
6-34
35-39
40-44
45-46
47
Page 2 www.sauder.com/service 429507
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
70 lbs.
70 lbs.
18-1/2"
18-1/2"
59"
59"

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3www.sauder.com/service429507
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F LARGE BOTTOM (1)
G SMALL BOTTOM (2)
H BACK (2)
I UPPER CENTER BACK (1)
J LOWER CENTER BACK (1)
K BRACE (2)
L ADJUSTABLE SHELF (2)
M SLIDING SHELF (1)
N UPPER LONG MOLDING (1)
O UPPER SHORT MOLDING (2)
P LOWER LONG MOLDING (2)
Q LOWER SHORT MOLDING (4)
R FOOT (8)
S RIGHT DRAWER SIDE (2)
T LEFT DRAWER SIDE (2)
U DRAWER BACK (2)
V DRAWER BOTTOM (2)
W DRAWER FRONT (2)
X RIGHT DOOR (1)
Y LEFT DOOR (1)
A
B
C
D
E
FG
H
I
J
K
L
M
NO
P
S
TU
V
W
X
S
T
U
V
W
Y
P
G
H
K
L
O
R
Q
R
R
Q
R

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/service 429507
(EXTENSION SET SHOWN SEPARATED)
ANGLED HEAD
CAM SCREW - 42
2
Angled head
LARGE HIDDEN
CAM - 42
1
WOOD
DOWEL - 38
6SHORT WOOD
DOWEL - 18
7
LONG WOOD
DOWEL - 4
5
SMALL HIDDEN
CAM - 8
3STRAIGHT HEAD
CAM SCREW - 8
4
Straight head
HINGE BRACKET - 4
11 HINGE - 4 12
GROMMET
WITH CAP - 2
9
PULL - 4
10
BB CABINET LEFT - 1 AA CABINET RIGHT - 1 DD DRAWER LEFT - 1 CC DRAWER RIGHT - 1
EXTENSION RAIL - 4
EE EXTENSION SLIDE - 4 FF
GROMMET - 3
8

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5www.sauder.com/service429507
METAL PIN - 8
14 RUBBER
SLEEVE - 8
15
APPLIQUE CARD - 1
16 LARGE
APPLIQUE CARD - 1
17
ADJUSTABLE
GLIDE - 8
13
BLACK 1-1/2" FLAT HEAD SCREW - 14
19
SILVER 1/2" FLAT HEAD SCREW - 8
22
BLACK 1/2" PAN HEAD SCREW - 24
21
BLACK 1-1/8" FLAT HEAD SCREW - 21
20
BLACK 1/2" FLAT HEAD SCREW - 20
23
(Refer to Step 23 for proper
location and application)
WARNING LABEL - 1
18
522,68 22,68
70 lbs. 31,75 kg 31,75 kg

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: If you are attaching the 429505 Hutch to your unit,
build that Hutch first.
å Before beginning this step, separate the LARGE HIDDEN
CAMS (1) from the SMALL HIDDEN CAMS (3). Do not
confuse these HIDDEN CAMS.
å Insert forty-two LARGE HIDDEN CAMS (1) into the
ENDS (A and B), UPRIGHTS (C and D), BOTTOMS (F and G),
BACKS (H, I, and J), and BRACES (K).
Page 6 www.sauder.com/service 429507
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 1
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
(42 used)
1
Arrow
A
B
C
D
F
G
HI
J
K
G
H
K

Step 2
Page 7www.sauder.com/service429507
A
B
C
D
å Before beginning this step, separate the ANGLED HEAD
CAM SCREWS (2) from the STRAIGHT HEAD CAM
SCREWS (4). Do not confuse these CAM SCREWS.
å Turn twenty ANGLED HEAD CAM SCREWS (2)
into the ENDS (A and B) and UPRIGHTS (C and D).
å NOTE: Use the exact holes shown.
Angled head
(20 used)
2
1

Step 3
Page 8 www.sauder.com/service 429507
A
B
å Separate the EXTENSION SLIDES (FF) from the EXTENSION RAILS (EE) as shown in the enlarged diagram below. Be
prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (EE) to the ENDS (A and B). Use six BLACK 1/2" PAN HEAD SCREWS (21).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that lines up with the holes in the ENDS. Turn a SCREW
into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
å Fasten the HINGE BRACKETS (11) to the ENDS (A and B) exactly as shown. Use the SCREWS in the brackets.
Open end
Open end
Push the black lever up and
pull the SLIDE from the RAIL.
BLACK 1/2" PAN HEAD SCREW
(6 used for the RAILS)
21
EE
EE
EE
FF
11
11
Use these holes.Open end
7

Step 4
Page 9www.sauder.com/service429507
å Fasten two EXTENSION RAILS (EE) to the UPRIGHTS (C and D). Use
six BLACK 1/2" PAN HEAD SCREWS (21).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole
shown in the enlarged diagram. Then, slide the inner cartridge of
the EXTENSION RAIL in to find the other holes that lines up with the
holes in the UPRIGHTS. Turn a SCREW into this hole.
C
D
EE
EE
BLACK 1/2" PAN HEAD SCREW
(6 used for the RAILS)
21
Open end
Open end
EE
Use these holes.
Open end
7

Step 5
Page 10 www.sauder.com/service 429507
å Peel the STICKERS from the LARGE APPLIQUE CARD (17) and
stick one onto each metal insert in a SMALL BOTTOM (G).
å Flip the SMALL BOTTOM (G) over.
å Turn four FEET (R) into the SMALL BOTTOM (G).
å NOTE: Do not overtighten the FEET.
å Repeat this step for the other SMALL BOTTOM (G).
17
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
G
G
F
L
I
P
O
V
E
R
R
R
R
R
(8 used)
Some assembly
(and snacks) required.