Sauder OFFICE WORKS AFFIRM Hudson Elm 427429 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Sauder.com
Share your journey!
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 574315 01/27/22
Purchased: __________________
AFFIRM COLLECTION
Hutch
Hudson Elm finish | Model 427429
How can we help you? To reach our customer service, visit sauder.com/commercial-oce/service
to chat with a live rep or email us.
Prefer the phone? Give us a ring at
877-996-7539 .
Our award-winning team is available Monday-Friday - 8:30 a.m. to 5 p.m. EST (except holidays).

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5
6-24
25-28
29-32
33-34
35
Tape Measure
Optional Accessory (sold separately)
å This piece of furniture accommodates the following optional accessory (sold separately).
å LED Light (Item 426494)
The LED Light is designed to be fastened to the underside of a hutch.
å To purchase the LED Light, scan this QR code. (Or go to sauder.com)
427429 www.sauder.com/commercial-oce/servicePage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D FIXED SHELF (1)
E OUTER DOOR (2)
F UPPER BACK (1)
G SHELF MOLDING (1)
H LOWER BACK (1)
J TOP (1)
K INNER DOOR (2)
A
B
C
D
E
F
G
H
J
K
E
K
427429www.sauder.com/commercial-oce/service Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
5G ANGLE
BRACKET - 4
10M TOUCH-UP PEN - 1 29M
BUMPER CARD - 2
1S BLACK 9/16" LARGE HEAD SCREW - 8 11S BLACK 1/2" FLAT HEAD SCREW - 16
1F HIDDEN CAM - 14 2F CAM DOWEL - 14
13H STRAIGHT HINGE - 4 40H CURVED HINGE - 4
42F WOOD DOWEL - 4
TAPE CARD/
PREP PAD KIT - 1
182M
Isopropyl
Alcohol 70%
Prep Pad
4P CORD CLIP - 1
129P CAM
COVER - 14
126P HOLE
PLUG - 1
FURNITURE TIPPING
RESTRAINT KIT - 1
97
TWIST-LOCK®
FASTENER COVER - 10
125P
GROMMET - 1
108P GROMMET CAP - 1 109P
BLACK 1-15/16" FLAT HEAD SCREW - 5
113S
427429 www.sauder.com/commercial-oce/servicePage 4

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
427429www.sauder.com/commercial-oce/service Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push six HIDDEN CAMS (1F) into the UPPER BACK (F).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 1
F
Arrow
1F
1F
Arrow
Arrow
1F
Just think. The sooner
you do this, the sooner
you do something else.
427429 www.sauder.com/commercial-oce/servicePage 6

StepStep 2
å Flip over the UPPER BACK (F) as shown.
å Fasten the FIXED SHELF (D) to the UPPER BACK (F). Use
three BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
F
D
BLACK 1-15/16" FLAT HEAD SCREW
(3 used in this step)
113S
Surface without HIDDEN CAMS
Surface with TWIST-LOCK® FASTENERS
427429www.sauder.com/commercial-oce/service Page 7

StepStep 3
å Push eight HIDDEN CAMS (1F) into the LOWER BACK (H). Then,
insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
1
H
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end
1F
2F
Arrow
Metal end
427429 www.sauder.com/commercial-oce/servicePage 8

StepStep 4
å Flip the LOWER BACK (H) over.
å Push the FIXED SHELF (D) onto the CAM DOWELS in the
LOWER BACK (H).
å NOTE: Do not tighten the HIDDEN CAMS in this step.
1
D
H
Surface without HIDDEN CAMS
427429www.sauder.com/commercial-oce/service Page 9

StepStep 5
å Insert two WOOD DOWELS (42F) into the ENDS (A and B).
å NOTE: You may need to gently tap the WOOD DOWELS in with your hammer.
å Insert the metal end of two CAM DOWELS (2F) into the holes shown in the UPPER BACK (F).
å Fasten the ENDS (A and B) to the FIXED SHELF (D) and BACKS (F and H). Tighten four TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert into the FIXED SHELF.
å NOTE: Do not tighten the HIDDEN CAMS in this step.
12
A
B
D
F
H
42F
42F
2F
Metal end
Metal end
2F
427429 www.sauder.com/commercial-oce/servicePage 10