Sauder Armoire 419451 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 397397 10/12/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Armoire
Model 419451
You could use a new
hide-and-seek spot.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Assembly Tools RequiredTable of Contents
Part Identification
3
4
5-22
23-25
26-28
29-30
31
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G DOOR (2)
H ADJUSTABLE SHELF (2)
I RIGHT FRONT LEG (1)
J LEFT FRONT LEG (1)
K BACK LEG (2)
L BOTTOM SKIRT (1)
M DRAWER FRONT (1)
D50 RIGHT DRAWER SIDE (1)
D51 LEFT DRAWER SIDE (1)
D80 DRAWER BACK (1)
D986 DRAWER BOTTOM (1)
M65 DRAWER BRACE (1)
419451 www.sauder.com/servicesPage 2

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
419451www.sauder.com/services Page 3
A
B
C
D
E
FG
H
I
J
K
LM
D50
D51
D80
D986
G
H
K
M65
Hardware Identification
HIDDEN CAM - 9
1F
40DC40DA UNIVERSAL CABINET RAIL - 2 DRAWER RIGHT - 1 40DD DRAWER LEFT - 1

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419451 www.sauder.com/servicesPage 4
SAFETY
BRACKET - 1
1G
GOLD 1" MACHINE SCREW - 2
50S
BLACK 9/16" LARGE HEAD SCREW - 5
1S
WASHER - 2
10I
BLACK 2-1/4" FLAT HEAD SCREW - 9
26S
CAM COVER - 6
19P
12F TWIST-LOCK®
FASTENER - 12
SILVER 1/4" MACHINE SCREW - 2
61S
3S GOLD 5/16" FLAT HEAD SCREW - 8
METAL PIN - 8
1R
BLACK 1/2" FLAT HEAD SCREW - 8
11S
CAM SCREW - 9
8F
DOOR STOP - 2
4I
WOOD DOWEL - 2
15F
NAIL - 44
1N
KNOB - 2
111K
PULL - 1
98K
RUBBER SLEEVE - 8
2R
DRAWER FRONT
BRACKET - 1
9G
14H HINGE - 4
30S BLACK 1-9/16" FLAT HEAD SCREW - 5
11L WARNING LABEL - 1
(Refer to Step 17 for
proper location and
application)
WARNING AVERTISSEMENT ADVERTENCIA
Serious or fatal crushing injuries can
occur from furniture tipover.
To help prevent tipover:
• Install tipover restraint provided.
• Place heaviest items in the lower drawers.
• Unless specifically designed to
accommodate, do not set TVs or other
heavy objects on top of this product.
• Never allow children to climb or hang on
drawers, doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer
interlock system.
Use of tipover restraints may only reduce,
but not eliminate, the risk of tipover.
This is a permanent label. Do not remove.
Des blessures graves ou fatales par écrasement
peuvent survenir si le mobilier bascule. Pour
prévenir le basculement:
• Installer le dispositif anti-basculement fourni.
• Placer les articles plus lourds dans les tiroirs inférieurs.
• Sauf si le meuble a été conçu spécialement à
cette fin, ne pas mettre de téléviseur ou d’autre
objets lourds sur le dessus de ce meuble.
• Ne jamais laisser d’enfants grimper sur les
tiroirs, les portes ou les étagères ou s’y agripper.
• Ne jamais ouvrir plus d’un tiroir à la fois.
(OU)
• Ne pas démanteler ou enlever le système de
verrouillage pour tiroir.
L’utilisation de dispositifs anti-basculement peut
réduire le risque de basculement, mais pas l’éliminer.
Cette étiquette est permanente. Ne pas l’enlever.
Lesiones graves o fatales por aplastamiento, pueden
ocurrir por el volcar de los muebles. Para ayudar a
prevenir que se volqué:
• Instalar la contención brindada para evitar que se volqué.
• Coloque los artículos más pesados en los cajones
inferiores.
• A menos que sea específicamente diseñado para
acomodar, no establezca televisores u otros objetos
pesados en la parte superior de este producto.
• Nunca permita que los niños se suban o se cuelguen
de cajones, puertas o estantes.
• Nunca abra más de un cajón a la vez.
(O)
• No anule o elimine el sistema de bloqueo de los cajones.
El uso de la contención puede solamente reducir, pero
no eliminar, el riesgo de volcar.
Esta es una etiqueta permanente. No remover.
10/16 395783

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
419451www.sauder.com/services Page 5
(12 used)
12F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (12F) into the large holes in the ENDS (A and B).
å Repeat this step for the BOTTOM (D) and SHELF (E).
A
B

Step 2
419451 www.sauder.com/servicesPage 6
8F
å Turn nine CAM SCREWS (8F) into the LEGS (I and J) and
DRAWER FRONT (M).
å Push nine HIDDEN CAMS (1F) into the ENDS (A and B)
and DRAWER BRACE (M65).
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
(9 used)
A
B
M
I
J
(9 used)
Arrow
1F
M65

Step 3
419451www.sauder.com/services Page 7
A
B
å Insert two WOOD DOWELS (15F) into the ENDS (A and B).
å Fasten the FRONT LEGS (I and J) to the ENDS (A and B).
Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the holes in the FRONT LEGS.
1
2
I
J
15F
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces must be even.
These surfaces must be even.
15F The LEG should
overhang this edge.

Step 4
419451 www.sauder.com/servicesPage 8
Remember:
Righty tighty.
Lefty loosey.
å Fasten the BACK LEGS (K) to the ENDS (A and B). Use
eight BLACK 2-1/4" FLAT HEAD SCREWS (26S).
BLACK 2-1/4" FLAT HEAD SCREW
(8 used in this step)
26S
The LEG should
overhang this edge.
These surfaces must be even.
K
K
A
B

Step 5
419451www.sauder.com/services Page 9
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
1
2
3
4
1
2
34
Glide end
Glide end
A
B
å Fasten the UNIVERSAL CABINET RAILS* (40DA) to
the ENDS (A and B). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S).
å *patent pending glide system

Step 6
419451 www.sauder.com/servicesPage 10
å Fasten the LEFT END (B) to the TOP (C). Tighten two
TWIST-LOCK® FASTENERS.
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
B
C
Surface with holes
Surface with
HIDDEN CAMS
These holes must be here.
J
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 7
419451www.sauder.com/services Page 11
B
E
å Fasten the SHELF (E) to the LEFT END (B). Tighten
two TWIST-LOCK® FASTENERS.
Surface with TWIST-LOCK® FASTENERS
Finished edge

Step 8
419451 www.sauder.com/servicesPage 12
å Fasten the BOTTOM (D) to the LEFT END (B).
Tighten two TWIST-LOCK® FASTENERS.
å Slide the BOTTOM SKIRT* (L) onto the notched
edge of the BOTTOM (D).
å *U.S. Patent No. 5,499,886
Notched edge
D
Surface with TWIST-LOCK® FASTENERS
L
Slide the BOTTOM SKIRT (L)
onto the notched edge.
B

Step 9
419451www.sauder.com/services Page 13
å Fasten the RIGHT END (A) to the TOP (C), BOTTOM (D),
and SHELF (E). Tighten six TWIST-LOCK® FASTENERS.
å Push two DOOR STOPS (4I) into the holes in the TOP (C).
D
E
C
Surface without
HIDDEN CAMS
I
4I
Don't worry. It isn't
Rome. This can be built
in a day.
A

Step 10
419451 www.sauder.com/servicesPage 14
å Carefully turn your unit over onto its front edges. Unfold
the BACK (F) and lay it over your unit.
å Make equal margins along all four edges of the BACK (F).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (F) to your unit using the NAILS (1N).
å NOTE: Be sure to tap NAILS into the holes that line up
over the SHELF (E).
Unfinished surface
NAIL
(44 used in this step)
1N
F
These holes must line
up over the SHELF (E).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 11
419451www.sauder.com/services Page 15
å Fasten two HINGES (14H) to each DOOR (G). Use eight
BLACK 1/2" FLAT HEAD SCREWS (11S).
14H
14H
G
G
BLACK 1/2” FLAT HEAD SCREW
(8 used in this step)
11S

Step 12
419451 www.sauder.com/servicesPage 16
å Carefully stand your unit upright.
å Before fastening the DOOR to your unit, be sure the
mounting screw is against the stops as shown in the right
diagram. If it isn't, loosen the mounting screw to slide it
against the stops. Then tighten the mounting screw.
å Fasten the DOOR (G) to the LEFT END (B) as shown in
the lower diagram. Use the screws in the HINGES. You
should start each SCREW a few turns before completely
tightening any of them.
å Fasten a KNOB (111K) to the DOOR (G). Use a GOLD 1"
MACHINE SCREW (50S).
å Repeat this step for the other DOOR (G).
å See the next step for DOOR adjustments.
Pro Tip: Lift with your
legs. And, you know,
your arms.
G
B
GOLD 1" MACHINE SCREW
(2 used in this step)
50S
111K
Mounting
screw
Stop
Hinge

Step 13
419451www.sauder.com/services Page 17
å Refer to the enlarged diagram to identify the parts on
the HINGES.
å The DOORS may need some adjustments. Follow the text
below to make needed adjustments.
å DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal) turn the
adjusting screw in or out.
å To adjust the DOORS up and down (vertical), loosen both
vertical adjustment screws. Move the DOORS up or down to the
desired location. Tighten the screws after making adjustments.
å To adjust the DOORS in or out (depth), loosen the mounting
screw one turn and move the DOORS in or out, as needed.
Tighten the mounting screw after making adjustments.
Adjusting screw (horizontal)
Mounting screw (depth)
(vertical adjustment)

Step 14
419451 www.sauder.com/servicesPage 18
å Pull the DRAWER FRONT BRACKETS (9G) apart and slide them into the grooves in the DRAWER SIDES (D50 and D51).
You may need to gently tap them in with a hammer.
å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification.
å Fasten the DRAWER FRONT (M) to the DRAWER FRONT BRACKETS (9G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
å Slide the DRAWER BOTTOM (D986) into the grooves in the DRAWER SIDES (D50 and D51) and DRAWER FRONT (M).
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
D50
D986
D51
M
D50
D51
M
VIEW THE T-SLOT BOX VIDEO
Push down
9G
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT groove.
With the palm of your hand, tap the
DRAWER BOTTOM down into the groove.
Unfinished surface
Groove

Step 15
419451www.sauder.com/services Page 19
å Fasten the DRAWER BRACE (M65) to the DRAWER FRONT (M). Tighten one HIDDEN CAM.
å Fasten the DRAWER BACK (D80) to the DRAWER SIDES (D50 and D51) and DRAWER BRACE (M65). Use five BLACK
1-9/16" FLAT HEAD SCREWS (30S).
Surface with
HIDDEN CAM
1
2
M
D50
D51
D80
M65
M65
VIEW THE T-SLOT BOX VIDEO
Be sure the
DRAWER
BOTTOM
inserts into
the DRAWER
BACK groove.
30S
Start each screw a few turns before
completely tightening any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(5 used in this step)

Step 16
419451 www.sauder.com/servicesPage 20
å Fasten a DRAWER RIGHT (40DC) to the DRAWER RIGHT
SIDE (D50) and a DRAWER LEFT (40DD) to the DRAWER
LEFT SIDE (D51). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #2.
å NOTE: The parts are marked "DRAWER RIGHT" and
"DRAWER LEFT" for easy identification.
å NOTE: The glides are not intended to rotate.
å Fasten the PULL (98K) to the DRAWER FRONT (M).
Use two WASHERS (10I) and two SILVER 1/4"
MACHINE SCREWS (61S).
1
2
Almost time to
celebrate! With a nap.
1
2
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
D50
D51
M
SILVER 1/4" MACHINE SCREW
(2 used for the PULLS)
61S
10I
98K
Glide end
Glide end