Sauder Shoal Creek 411201 User manual

User Manual of Product 1:
Sauder Shoal Creek Dresser, L: 54.65" x W: 18.43" x H: 33.03",
Soft White finish

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey! Lot # 589613 12/12/22
Purchased: __________________
English pg 1-47
Français pg 48-53
Español pg 54-59
Dresser
Shoal Creek Collection | Model 411201
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
2-3
4-5
6
7-47
48-53
54-59
60-62
63
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A3 RIGHT END (1)
B3 LEFT END (1)
B65 DRAWER BOTTOM (6)
C3 UPRIGHT (1)
D3 TOP (1)
D593 SMALL RIGHT DRAWER SIDE (2)
D594 SMALL LEFT DRAWER SIDE (2)
- 1 with label
D595 SMALL DRAWER BACK (2)
D596 RIGHT DRAWER SIDE (4)
D623 LEFT DRAWER SIDE (4)
D624 DRAWER BACK (4)
E3 BOTTOM (2)
F2 BACK (1)
G RIGHT FRONT LEG (1)
H LEFT FRONT LEG (1)
I2 REAR LEG (2)
K3 SMALL RIGHT DRAWER FRONT (1)
L3 SMALL LEFT DRAWER FRONT (1)
M65
DRAWER BRACE (6)
(Hidden part using recycled
material. Color may vary.)
M73 END MOLDING (2)
Q3 RIGHT DRAWER FRONT (2)
R3 LEFT DRAWER FRONT (2)
YY GROOVED EXTENSION BLOCK (2)
ZZ EXTENSION BLOCK (2)
411201 www.sauder.com/servicePage 2

Part Identification Now you know
our ABCs.
411201www.sauder.com/service Page 3
F2 G
H
D593
M73
B65
D594
D595
M65
D596
B65
D623
D624
M65
R3
Q3
K3
L3
D593
B65
D594
D595
M65
D596
B65
D623
D624
M65
M73
I2
I2
D3
A3
C3
B3
YY
ZZ
YY
ZZ
E3
E3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
40CA CABINET RIGHT - 6 40CB CABINET LEFT - 6 40CC DRAWER RIGHT - 6 40CD DRAWER LEFT - 6
34E ADJUSTABLE
FOOT - 1
10A SLIDE CAM - 12 1F HIDDEN CAM - 22 2F CAM DOWEL - 16
8F CAM SCREW - 6 31K PULL - 8 KNOB - 4
185K 1N NAIL - 43
FURNITURE TIPPING
RESTRAINT KIT - 1
971R METAL PIN - 4
411201 www.sauder.com/servicePage 4
1T INTERLOCK
TRACK - 2

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1S BLACK 9/16" LARGE HEAD SCREW - 4 3S GOLD 5/16" FLAT HEAD SCREW - 48
10S SILVER 1-1/8" FLAT HEAD SCREW - 12 20S SILVER 3/4" MACHINE SCREW - 16
21S BLACK 1-1/8" MACHINE SCREW - 4 26S BLACK 2-1/4" FLAT HEAD SCREW - 6
30S BLACK 1-9/16" FLAT HEAD SCREW - 30 32S BLACK 9/16" FLAT HEAD SCREW - 4
62S BLACK 9/16" EURO SCREW - 4 BLACK 1-15/16" FLAT HEAD SCREW - 2 113S
411201www.sauder.com/service Page 5

Hardware Usage Guide
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
411201 www.sauder.com/servicePage 6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn two BLACK 9/16" FLAT HEAD SCREWS (32S) into
the LEFT END (B3) until the shoulders of the SCREWS
rest on the surface of the END.
å NOTE: Do not overtighten the SCREWS.
å Slide one END MOLDING (M73) onto the LEFT END (B3).
Line up the groove in the MOLDING over the heads of the
SCREWS in the END.
å NOTE: The MOLDING should be centered on the END.
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0
BLACK 9/16" FLAT HEAD SCREW
(2 used in this step)
32S
B3
Surface with fewer holes
Apply pressure with your hands
as you guide the MOLDING over
the SCREWS and onto the END.
Shoulder
M73
411201www.sauder.com/service Page 7
Just think. The sooner
you do this, the sooner
you do something else.

å Carefully flip the LEFT END (B3) over.
å Push two HIDDEN CAMS (1F) into the short edge of the
LEFT END (B3). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
å Push three HIDDEN CAMS (1F) into the long edge of the
LEFT END (B3).
Step 2
411201 www.sauder.com/servicePage 8
1F
Arrow
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
1
B3

å Turn three CAM SCREWS (8F) into the LEFT
FRONT LEG (H).
Step 3
411201www.sauder.com/service Page 9
1
8F
H

Step 4
411201 www.sauder.com/servicePage 10
1
H
I2
Surface with HIDDEN CAMS
å Fasten the LEFT END (B3) to the LEFT FRONT LEG (H).
Tighten three HIDDEN CAMS.
å Fasten one REAR LEG (I2) to the LEFT END (B3). Use
three BLACK 2-1/4" FLAT HEAD SCREWS (26S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
These surfaces
should be even.
The LEGS will
overhang this edge.
Edge with
CAM DOWELS
B3
Angled edge
Angled edge
BLACK 2-1/4" FLAT HEAD SCREW
(3 used in this step)
26S

å Fasten three CABINET LEFTS (40CB) to the LEFT END (B3).
Use six GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #3.
Step 5
411201www.sauder.com/service Page 11
1
2
3
4
GOLD 5/16" FLAT HEAD SCREW
(6 used in this step)
3S
5
B3
Edge with
CAM DOWELS
Roller end
1
2
3
4
1
2
3
4

å Open the FURNITURE TIPPING RESTRAINT KIT (97),
and fasten the SAFETY STRAP to the TOP (D3). Use the
provided SHORT SCREW.
å NOTE: Position the SAFETY STRAP exactly as shown.
Step 6
411201 www.sauder.com/servicePage 12
Use this hole if you prefer
the SAFETY STRAP on the
right side of the UPRIGHT.
Use this hole if you prefer
the SAFETY STRAP on the
left side of the UPRIGHT.
SHORT SCREW
97
The SAFETY DRYWALL
ANCHOR and WASHER
will be used later.
SAFETY STRAP
D3

å Fasten the LEFT END (B3) to the TOP (D3). Tighten two
HIDDEN CAMS.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Step 7
411201www.sauder.com/service Page 13
1
D3
Surface
with
HIDDEN
CAMS
B3
SAFETY STRAP

å Push two HIDDEN CAMS (1F) into the UPRIGHT (C3).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
Step 8
411201 www.sauder.com/servicePage 14
Do not tighten the HIDDEN CAMS in this step.
1F
2F
Arrow
Metal end
1
C3

å Fasten one of each EXTENSION BLOCK (YY and ZZ)
to the UPRIGHT (C3). Use six SILVER 1-1/8" FLAT
HEAD SCREWS (10S).
å NOTE: You should start each SCREW a few turns
before completely tightening any of them.
Step 9
411201www.sauder.com/service Page 15
YY
C3
ZZ
SILVER 1-1/8" FLAT HEAD SCREW
(6 used in this step)
10S
The hole is closer
to this edge.
The large hole must be here.
Edge with
CAM DOWELS
Surface
with
HIDDEN
CAMS
Some assembly
(and snacks) required.

å Insert the post in the INTERLOCK TRACK (1T) into the
large hole in the GROOVED EXTENSION BLOCK (YY)
and lay the INTERLOCK TRACK into the groove in the
EXTENSION BLOCK.
Step 10
411201 www.sauder.com/servicePage 16
IMPORTANT
The INTERLOCK
TRACK is a safety
feature that must be
installed in your unit.
YY
1T
Large hole
Post
- VIEW FROM BOTTOM -
Groove

å Fasten three CABINET RIGHTS (40CA) to the EXTENSION
BLOCKS (YY and ZZ). Use six GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
å NOTE: The RAILS will over lap the INTERLOCK TRACK slightly.
Step 11
411201www.sauder.com/service Page 17
5
1
2
3
4
GOLD 5/16" FLAT HEAD SCREW
(6 used in this step)
3S
ZZ
Edge with
CAM DOWELS
Roller end
YY
1
2
3
4
1
2
3
4

å Carefully flip the UPRIGHT (C3) over.
å Fasten the remaining three CABINET LEFTS (40CB)
to the UPRIGHT (C3). Use six GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
Step 12
411201 www.sauder.com/servicePage 18
3
2
1
4
5
C3
Edge with
CAM DOWELS
Surface without
HIDDEN CAMS
GOLD 5/16" FLAT HEAD SCREW
(6 used in this step)
3S
Roller end
3
2
1
4
3
2
1
4

å Fasten the UPRIGHT (C3) to the TOP (D3). Tighten two
HIDDEN CAMS.
Step 13
411201www.sauder.com/service Page 19
1
C3
Surface
without
HIDDEN
CAMS
D3