Sauder Storage Cabinet 419496 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
Storage Cabinet
419496
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-18
Français pg 19-21
Español pg 22-24
Lot #: 374611
Date Purchased: __________________
06/15/15
Be sure to give us a ring before
making any returns. 1-800-445-1527
You'll love what we
have in storage.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4
5-18
19-21
22-24
25-26
27
Page 2 www.sauder.com/services 419496
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F SHELF (1)
G BACK (1)
H RIGHT DOOR (1)
I LEFT DOOR (1)
J ADJUSTABLE SHELF (4)
K FRONT SKIRT (1)
L BACK SKIRT (1)
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
Electric drill with 1/4" bit
(ONLY in indicated step)

Part Identification
Page 3
www.sauder.com/services419496
A
B
C
D
E
F
G
H
I
J
K
L
J
J
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 419496
SAFETY DRYWALL
ANCHOR - 1
5
Locate this SAFETY STRAP (6)
to be used later in assembly. Do
not accidentally throw away.
SAFETY STRAP - 1
6
1/2" PAN HEAD SCREW - 12
16
1" PAN HEAD SCREW - 1
12
5/8" PAN HEAD SCREW - 1
13 5/8" MACHINE SCREW - 4 14
1/2" FLAT HEAD SCREW - 12
15
PULL - 2
4
APPLIQUE - 22
7
ANGLE BRACKET - 6
1
1-3/8" FLAT HEAD SCREW - 24
11
HINGE - 6
2HINGE BRACKET - 6 3
NAIL - 38
10
METAL PIN - 16
8RUBBER SLEEVE - 16 9

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten six ANGLE BRACKETS (1) to the SKIRTS (K and L).
Use six 1/2" PAN HEAD SCREWS (16).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the SKIRTS.
Page 5
www.sauder.com/services419496
1/2" PAN HEAD SCREW
(6 used in this step)
16
1
K
L
(6 used)

å Fasten the SKIRTS (K and L) to the BOTTOM (E). Use
six 1/2" PAN HEAD SCREWS (16) through the ANGLE
BRACKETS on the SKIRTS and into the BOTTOM.
Step 2
Page 6 www.sauder.com/services 419496
K
L
E
1/2" PAN HEAD SCREW
(6 used in this step)
16
The molding on the
BOTTOM should be here.

å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two
1-3/8" FLAT HEAD SCREWS (11).
Step 3
Page 7
www.sauder.com/services419496
E
K
L
C
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
1-3/8" FLAT HEAD SCREW
(2 used in this step)
11

å Fasten the SHELF (F) to the UPRIGHT (C). Use two 1-3/8"
FLAT HEAD SCREWS (11).
å Then, peel two APPLIQUES (7) from the applique card
and stick them over the head of the SCREWS.
Step 4
Page 8 www.sauder.com/services 419496
E
C
F
The molding on the
SHELF should be here.
Peel the APPLIQUES
from the applique card.
7
1-3/8" FLAT HEAD SCREW
(2 used in this step)
11

å Fasten the HINGE BRACKETS (3) to the ENDS (A and B).
Use the SCREWS in the HINGE BRACKETS.
Step 5
Page 9
www.sauder.com/services419496
B
A
3
3
3

å Fasten the LEFT END (B) to the TOP (D), BOTTOM (E),
SHELF (F), and SKIRTS (K and L). Use ten 1-3/8" FLAT
HEAD SCREWS (11).
å Then, peel ten APPLIQUES (7) from the applique card
and stick them over the head of the SCREWS.
Step 6
Page 10 www.sauder.com/services 419496
E
F
K
L
D
(10 used)
To cover screws
7
Edge with
HINGE BRACKETS
B
Finished surface
1-3/8" FLAT HEAD SCREW
(10 used in this step)
11