Sauder Cottage Road L Desk 431264 User manual

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
35MA EXTENSION SLIDE - 4 35MC 10A SLIDE CAM - 4 FILE GLIDE - 2
4B
FILE ROD - 2
8B HIDDEN CAM - 66 1F CAM DOWEL - 34 2F CAM SCREW - 32 8F
WOOD DOWEL - 34
15F 37F TWIST-LOCK®
FASTENER - 8
METAL
BRACKET - 3
4G CONNECTOR
PLATE - 1
14G
KNOB SET - 4
136K GROMMET CAP - 2
1P GROMMET - 2 10P
SCREW COVER - 8
74P APPLIQUE CARD - 5 89P METAL PIN - 3 1R

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
BLACK 9/16" LARGE HEAD SCREW - 14
1S 3S GOLD 5/16" FLAT HEAD SCREW - 16
30S BLACK 1-9/16" FLAT HEAD SCREW - 8 BLACK 9/16" FLAT HEAD SCREW - 4 32S
GOLD 1" MACHINE SCREW - 4
50S BLACK 1-15/16" FLAT HEAD SCREW - 10 113S

å Fasten the LEFT SUPPORT (CC) to the SMALL MODESTY
PANEL (O) and SMALL BRACE (W). Use four BLACK
1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 2
Page 8
O
CC
Surface with HIDDEN CAMS
Surface without HIDDEN CAMS
W
For support, place packing
foam and magazines here.
Edge with CAM DOWELS
Curved edge
BLACK 1-15/16" FLAT HEAD SCREW
(4 used in this step)
113S

å Push two HIDDEN CAMS (1F) into the short edge of
the UPRIGHT (J). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
å Now, push six HIDDEN CAMS (1F) into the UPRIGHT (J)
and one SIDE SKIRT (T).
Step 3
Page 9
Arrow
1F
2F
Metal end
1F
Arrow
1F
Arrow
J
T
Do not tighten the HIDDEN CAMS in this step.
The holes are
closer to this edge.

å Turn twelve CAM SCREWS (8F) into the LEGS (M and N).
å Insert six WOOD DOWELS (15F) into the LEGS (M and N).
Step 4
M
N
Page 10
8F
15F
15F
15F
8F 8F
(12 used)

å Fasten the LEGS (M and N) to the UPRIGHT (J) and SIDE
SKIRT (T). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS insert
into the UPRIGHT.
Step 5
M
N
Page 11
Surface with
HIDDEN CAMS
These surfaces
should be even.
Edge with
CAM DOWELS
J
T
The holes are
closer to this edge.

Step 6
Page 12
å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (35MA) to the UPRIGHT (J). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged
diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other hole
that lines up with the hole in the UPRIGHT. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWERS.
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC
1
2
3
J
Open end
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(4 used for the RAILS)
3S

å Fasten the CENTER REAR LEG (N) to the SMALL MODESTY
PANEL (O). Tighten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEG insert into the
MODESTY PANEL.
å Fasten the CENTER REAR LEG (N) to the SMALL BRACE (W).
Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 7
Page 13
N
W
O
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S

å Push two HIDDEN CAMS (1F) into the short edge of the
BACK (E). Then, insert the metal end of a CAM DOWEL (2F)
into each HIDDEN CAM.
å Now, push four HIDDEN CAMS (1F) into the remaining holes
in the BACK (E).
Step 8
Page 14
Arrow
1F
2F
Metal end
1F
Arrow
1F
Arrow
E
Do not tighten the HIDDEN CAMS in this step.

å Fasten the BACK (E) to the CENTER REAR LEG (N).
Tighten two HIDDEN CAMS.
Step 9
Page 15
E
For support, place packing
foam and magazines here.
N
Edge with
CAM DOWELS

å Push four HIDDEN CAMS (1F) into the SKIRTS (R).
å Push twelve HIDDEN CAMS (1F) into the BOTTOMS (F
and G). Then, insert the metal end of a CAM DOWEL (2F)
into each HIDDEN CAM.
Step 10
Page 16
1F
Arrow
1F
Arrow
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end
1F
2F
Arrow
Metal end
1F
2F
Metal end
Arrow
R
R
G
F
F
G

å Insert four WOOD DOWELS (15F) into the BOTTOMS (F and G).
å Fasten the SKIRTS (R) to the BOTTOMS (F and G). Tighten eight
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the BOTTOMS insert into
the SKIRTS.
Step 11
Page 17
Edge with
CAM DOWELS
Edge with
CAM DOWELS
R
R
G
F
F
G
15F
15F
These surfaces
should be even.
These surfaces
should be even.

å Fasten one of the OUTER BOTTOMS (G) to the LEGS (M
and N) and SIDE SKIRT (T). Tighten four HIDDEN CAMS.
Step 12
Page 18
T
G
N
M

å Push two HIDDEN CAMS (1F) into the short edge of
the LEFT END (B). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
å Now, push six HIDDEN CAMS (1F) into the LEFT END (B)
and remaining SIDE SKIRT (T).
Step 14
Page 20
1F
Arrow
1F
Arrow
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
T
B