Sauder 426930 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-20
Français pg 21-24
Español pg 25-28
Lot # 543096 02/20/20
Purchased: __________________
3-Door Wardrobe
Model 426930
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
åUse this part identification to help identify the parts.
Table of Contents Assembly Tools Required
2-3
4
5-20
21-24
25-28
29-30
31
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
A LEFT END (1)
B RIGHT END (1)
C UPRIGHT (1)
D DOOR (3)
E BACK (1)
F TOP (1)
G BOTTOM (1)
H FIXED SHELF (1)
J SHORT BRACE (2)
K ADJUSTABLE SHELF (3)
L BACK SKIRT (1)
M FRONT SKIRT (1)
N LONG BRACE (1)
Part Identification Now you know
our ABCs.
Page 2 www.sauder.com/service 426930
Electric drill with 1/8" bit
(ONLY in indicated step)

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification Now you know
our ABCs.
A
B
C
D
D
D
E
F
G
H
J
J
K
K
K
L
M
N
Page 3www.sauder.com/service426930

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
WOOD DOWEL - 4
1ROD HANGER - 2 2ROD - 1
3PULL - 3 4
HINGE - 9
5METAL BRACKET - 6 6NAIL - 62 7SHELF PIN - 12 8
9BUMPER CARD - 1 APPLIQUE CARD - 2 10 FURNITURE TIPPING RESTRAINT KIT - 1 98
11 1-9/16" FLAT HEAD SCREW - 30
1/2" FLAT HEAD SCREW - 64
13
15/16" PAN HEAD SCREW - 6
12
Page 4 www.sauder.com/service 426930

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten a ROD HANGER (2) to the UPRIGHT (C). Use two
1/2" FLAT HEAD SCREWS (13).
1/2" FLAT HEAD SCREW
(2 used in this step)
13
C
2
Surface with fewer holes
Page 5www.sauder.com/service426930

å Fasten the TOP (F) and BOTTOM (G) to the UPRIGHT (C).
Use four 1-9/16" FLAT HEAD SCREWS (11).
Step 2
C
F
G
11
Surface with
more holes
Unfinished edge
Hole on other surface
should be here.
1-9/16" FLAT HEAD SCREW
(4 used in this step)
11
Page 6 www.sauder.com/service 426930
Just think. The sooner
you do this, the sooner
you do something else.

Step 3
å Fasten the FIXED SHELF (H) to the UPRIGHT (C). Use two
1-9/16" FLAT HEAD SCREWS (11).
C
H
Unfinished edge
1-9/16" FLAT HEAD SCREW
(2 used in this step)
11
Page 7www.sauder.com/service426930

Step 4
å Fasten the ROD HANGER (2) to the LEFT END (A). Use
two 1/2" FLAT HEAD SCREWS (13).
A
1/2" FLAT HEAD SCREW
(2 used in this step)
13
2
Page 8 www.sauder.com/service 426930

å Fasten the LEFT END (A) to the TOP (F), FIXED SHELF (H), and
BOTTOM (G). Use six 1-9/16" FLAT HEAD SCREWS (11).
å Fasten the LONG BRACE (N) to the UPRIGHT (C) and LEFT
END (A). Use four 1-9/16" FLAT HEAD SCREWS (11).
Step 5
A
G
F
H
C
N
Unfinished edge
11
1-9/16" FLAT HEAD SCREW
(10 used in this step)
11
Page 9www.sauder.com/service426930

1
Step 6
å Fasten one METAL BRACKET (6) to the BACK SKIRT (L)
exactly as shown. Use two 1/2" FLAT HEAD SCREWS (13).
å Insert two WOOD DOWELS (1) into the holes in the
BACK SKIRT (L).
å Fasten the BACK SKIRT (L) to the LEFT END (A). Use one
1-9/16" FLAT HEAD SCREW (11).
å NOTE: Be sure the WOOD DOWEL in the BACK SKIRT
inserts into the LEFT END (A).
å Fasten the BACK SKIRT (L) to the BOTTOM (G). Use
two 1/2" FLAT HEAD SCREWS (13) through the METAL
BRACKET and into the BOTTOM.
L
6
1
1/2" FLAT HEAD SCREW
(4 used for the METAL BRACKET)
13
A
G
L
13
1-9/16" FLAT HEAD SCREW
(1 used for the BACK SKIRT)
11
Page 10 www.sauder.com/service 426930

å Fasten the RIGHT END (B). to the TOP (F), BOTTOM (G), and
BACK SKIRT (L). Use five 1-9/16" FLAT HEAD SCREWS (11).
å NOTE: Be sure the WOOD DOWEL in the BACK SKIRT inserts
into the RIGHT END (B).
å Fasten the SHORT BRACES (J) to the UPRIGHT (C) and
RIGHT END (B). Use eight 1-9/16" FLAT HEAD SCREWS (11).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 7
G
L
B
C
J
J
F
Surface with
less holes
11
Unfinished edge
1-9/16" FLAT HEAD SCREW
(13 used in this step)
11
Page 11www.sauder.com/service426930

Step 8
å Unfold the BACK (E) and lay it over your unit.
å Make equal margins along all four edges of the BACK (E).
Push on opposite corners of your unit if needed to make it
"square".
å Fasten the BACK (E) to your unit using the NAILS (7). The
NAILS should be 4" apart and 1/4" in from the edges.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
8
4"
1/4"
G
B
E
F
A
NAIL
(62 used in this step)
7
Unfinished
surface
Page 12 www.sauder.com/service 426930

Step 9
å Carefully turn your unit onto its back edges.
å Insert two WOOD DOWELS (1) into the ENDS (A and B)
as shown.
å Fasten five METAL BRACKETS (6) to the FRONT
SKIRT (M). Use ten 1/2" FLAT HEAD SCREWS (13).
å Fasten the FRONT SKIRT (M) to the BOTTOM (G) and
ENDS (A and B). Use ten 1/2" FLAT HEAD SCREWS (13)
through the METAL BRACKET and into the BOTTOM
and ENDS.
å NOTE: Be sure the WOOD DOWEL in the ENDS insert
into the holes in the FRONT SKIRT.
B
A
M
G
1
1
M
6
6
1/2" FLAT HEAD SCREW
(20 used in this step)
13
Surface without holes
13
Page 13www.sauder.com/service426930
6

å Fasten three HINGES (5) to a DOOR (D). Use six 1/2"
FLAT HEAD SCREWS (13).
å Repeat this step for the remaining DOORS.
Step 10
D
5
x3
1/2" FLAT HEAD SCREW
(18 used in this step)
13
Page 14 www.sauder.com/service 426930

Step 11
å Fasten the DOORS (D) to the ENDS (A and B) and
the UPRIGHT (C). Use eighteen 1/2" FLAT HEAD
SCREWS (13).
å Fasten the PULLS (4) to the DOORS (D). Use six 15/16"
PAN HEAD SCREWS (12).
D
D
A
CB
D
1/2" FLAT HEAD SCREW
(18 used for the HINGES)
13
15/16" PAN HEAD SCREW
(6 used for the PULLS)
12
13
4
4
4
Page 15www.sauder.com/service426930
5

Step 12
Page 16 www.sauder.com/service 426930
å Carefully stand your unit upright.
å Open the FURNITURE TIPPING RESTRAINT KIT (98) and fasten the SAFETY STRAP to the TOP (F) shown. Use the
provided short screw.
å Place your unit in its final location against a wall. Locate the center of a stud in your wall near your unit and mark it
with a pencil. Next, drill a 1/8" hole on the mark and into the stud in your wall.
å Fasten the unit to the wall. Use the long screw through the other end of the strap and into the 1/8" hole.
å Insert the SHELF PINS (8) into the hole locations of your choice in the RIGHT END (B) and UPRIGHT (C).
98
98
Electric drill with 1/8" bit
Drill 1/8" hole into
a stud in your wall.
F
B
C
Use the short screw through
the hole in the strap and into
the top surface of the
TOP (F).
8
(12 used)
8

Step 13
Page 17www.sauder.com/service426930
å Refer to the enlarged diagram to identify the parts on
the HINGES.
å The DOORS may need some adjustments. Follow the text
below to make needed adjustments.
å DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal), turn the
adjusting screw in or out.
å To adjust the DOORS up and down (vertical), remove the
round hole screws and loosen the slotted hole screws.
Move the DOORS up or down to the desired location.
Tighten the slotted hole screws first. Then turn the round
holes screws into their holes.
å To adjust the DOORS in or out (depth), loosen the
mounting screw one turn and move the DOORS in or out,
as needed. Tighten the mounting screw after
making adjustments.
(vertical adjustment)
2 screws
Adjusting screw (horizontal)
Mounting screw (depth)
17

Step 14
å Set the ADJUSTABLE SHELVES (K) onto the SHELF PINS.
å Peel APPLIQUES from the APPLIQUE CARDS (10) and
stick them onto each visible SCREW head.
Page 18 www.sauder.com/service 426930
K
K
K
10
To cover SCREWS
B
(2 used)

å Peel the BUMPERS from the BUMPER CARD (9) and
stick them onto the TOP (F) and BOTTOM (G) where they
come in contact with the DOORS (D).
Step 15
Page 19www.sauder.com/service426930
F
G
9
9
D
D
D

Step 16
å Insert the ROD (3) into the ROD HANGERS (2).
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Page 20 www.sauder.com/service 426930
And to celebrate, why not share your success story at sauder.com or
25 lbs.
25 lbs.
25 lbs.
50 lbs. total
35 lbs.
No load
2
40 lbs.
3