Savant SmartControl 3 User manual

Savant® SmartControl 3 (SSC-W003I-01)
Quick Reference Guide
SSC-W003I-01 | 009-1504-00 | 170602!
!
!
!
45 Perseverance Way, Hyannis, MA 02601!
Copyright © 2017 Savant Systems, LLC
1
of
2!
Savant.com | 508.683.2500
Box Contents
(1) SmartControl 3 Controller (SSC-W003I-01)
(1) Installation Kit (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0165-xx)
(1) Cable Tie (014-0071-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature
32° to 104° F (0° to 40°C)
Humidity
10% to 90% (non-condensing)
Dimensions and Weight (Product)
Height
0.64 in (1.62 cm)
Width
2.70 in (6.85 cm)
Depth
2.67 in (6.78 cm)
Weight
Net: 0.25 lb (0.11 kg)
Shipping: 1.50 lb (0.68 kg)
Power
Input Power
5V DC 1.2A
Max Power
6 watts
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
IMPORTANT! 802.11r (fast roaming) is
not supported.
Security
WPA™, WPA2™, WPA/WPA2™, WEP
Regulatory
Safety and
Emissions
FCC Part 15 | CE Mark | C-Tick
Contains FCC ID:
TLZ-CU277
Contains IC:
6100A-CU277
RoHS
Compliant
Minimum Supported Release
Savant OS
da Vinci 8.4
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards listed
in the Specifications Table.
Connect all Savant devices to the same local area network (LAN) or
subnet as the Host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power
outage, a static IP Address or DHCP reservation should be
configured. Savant recommends using DHCP reservation within the
router. By using this method, static IP Addresses for all devices can
be managed from a single UI avoiding the need to access devices
individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Front Panel
Press and hold for five seconds while powered On to clear the
network settings. The Status LED blinks rapidly when reset is
complete.
Off: No Power
On Solid: Provisioned to the local network and communicating
with the Savant Pro System Host.
Blinks Once: In Provisioning Mode. Ready to be added to the
local network.
Blinks Twice: Establishing connection with the local network.
Blinks Three Times: Connected to the local network. Is
connecting to the Host.
Short Off Blink: Firmware is updating.
Rapid Blink: The reset button was held down for at least five
seconds and the SSC-W003I is performing a factory reset.
After reset, all network settings are cleared and the factory
defaults are set.
Rear Panel
IR
Used to send IR signals to control devices with an IR
input or IR receiver via an IR flasher (5V tolerant
only).
Before making connections, see the IR Wiring section
below for important precautions regarding IR
functionality.
Input
Power
5V DC 1.2A - Connect to included power supply.
Cable
Lance
Use with included cable tie to secure power supply
connection.
A
B
A
B
C

SSC-W003I-01 | 009-1504-00 | 170602!
!
!
!
45 Perseverance Way, Hyannis, MA 02601!
Copyright © 2017 Savant Systems, LLC
2
of
2!
Savant.com | 508.683.2500
IR Wiring
IR connections are made using the 6-pin screw down plug-in type
connector included with each SSC-W003I controller. This connector
plugs into the connection on the rear of the controller.
IMPORTANT! IR Wiring Precuations
-!Ensure all IR emitters are within 15 feet (4.6 meters) from the
controller’s location.
-!Use of 3rd party flashing IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage
away from the IR signal that can degrade IR performance.
Making Connections
1.!Remove Power if power is applied.
2.!Pull to remove the terminal block from the rear of the controller.
3.!With a small flat bladed screwdriver, turn the screws on the top
of connector counterclockwise until the silver crimps in the front
of the connector opens enough to slide the wire(s) into the
square slots.
4.!Insert the stripped wires from the first IR input or output device
into ports 1 and 2 observing the correct signals. Do not allow
more than ½inch of bare wire exposed.
5.!Turn the screws clockwise until the screw tightens around the
wire. Tug on the wire a bit to verify the wires are installed
securely.
6.!Continue until all wires are installed.
7.!Repeat steps 3 - 5 for any additional IR devices.
8.!Plug terminal block back into the rear of the controller.
9.!Reapply power.
Connecting to a Wireless Network
To provision the SSC-W003I controller onto a local network, one of
the following methods can be used:
-!SmartConnect Application – da Vinci 8.4 or later.
-!Embedded Web UI – All da Vinci builds.
Both methods are described in the SmartControl 3 – (SSC-W003I)
Deployment Guide.
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
-!SmartControl 3 (SSC-W003I) Deployment Guide (009-0274-xx)
-!SmartConnect Software Reference Guide (009-1046-xx)
-!SmartControl 3 SSC-W003I Troubleshooting Guide.
-!Videos on the Savant Controllers Family in the pages of the
Savant University.
Regulatory
The following statements are applicable to the SSC-W003I.
FCC Regulations:
15.19. These devices comply with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) These devices may not cause harmful
interference, and (2) these devices must accept any interference received,
including interferences that may cause undesired operation.
15.21. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
15.105. This equipment has been tested and found to comply with the limits for
CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications, However there is no guarantee that interference will not occur
in a particular installation, If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving circuit different from that to which receiver is
connected.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or experienced radio/TV technician for help.
IC Regulations:
RSS-Gen 7.1.3. These devices comply with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) These
devices may not cause interference, and (2) These devices must accept any
interference, including interference that may cause undesired operation of the
device.
RSS-21- Annexe 9: A 9.4. Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.