Savant SHC-S2-00 User manual

SHC-S2-00 | 009-1775-00 | 181204
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 2
Rear Panel
A
Reset (hole)
To clear all Ethernet settings and revert them
back to their factory defaults, press and hold the
reset button for five seconds until the LED blinks
red rapidly; then release.
B
Power Input
5V DC 3A - Connect included wall wart power
supply between the 5V DC connection
and a 115-240V AC surge protected
outlet.
CStatus LED
O - Disconnected from power supply.
Amber - Host is booting/rebooting and is
disconnected from the network.
1s1s 1s
Repeat
1s
Amber Flashing - Host is in
provisioning mode and ready to be added to a
network. Host is not assigned an IP Address.
Green - Connected to the local network and
is assigned an IP Address.
DDigital Au-
dio Output
TOSLink (Optical) digital audio output. Connect
to digital optical audio input on switcher for
using the Audio Interrupt Service (AIS).
E
Ethernet
8-pin RJ-45 female.
10/100/1000 Base-T auto negotiating port. Con-
necting to this port will disable Wi-Fi settings.
F
RS-232
8-pin RJ-45 female.
Used to transmit and receive serial binary data
to and from serial controllable devices.
Ports 1-2 RS-232 - CTS/RTS handshaking. CTS
RTS handshaking availability is based on the
component profile.
See RS-232 Wiring section for pin-outs.
G
IR
6-pin Screw Down Plug-in Connector. Used to
send IR signals to control devices with an IR
input or IR receiver via an IR flasher (5V toler-
ant only). See IR Wiring section for important
precautions regarding IR functionality before
making connections.
H
Relay
3-pin Screw Down Plug-in Connector. See Relay
Wiring section for pin-outs.
Normally Open (NO) / Normally Closed (NC) to
control devices requiring basic on/o operation.
DC Voltage Max: 30V DC 1A
I
GPIO
3-pin Screw Down Plug-in Connector. See GPIO
Wiring section for pin-outs.
GPIO Input - When configured as an input, the
processor will look for a low (<0.8V DC) or a
high (>2.4V DC) state.
Minimum 0V DC / Maximum 12V DC.
GPIO Output - When configured as an output,
the port provides a binary output of 0-12V DC
150mA max.
(1) Savant® Smart Host with Control 2 - (SHC-S2-00)
(1) 5V DC 3A Power Supply
with Quick Change AC Adapters (025-0153-xx)
(2) M3 x 6 mm Flathead Phillips Screw Black (039-0001-xx)
(2) 6-pin Screw Down Plug-in Connector Black (028-0664-xx)
(2) 3-pin Screw Down Plug-in Connector Black (028-0665-xx)
(1) Wall Mount Frame (074-0585-xx)
(1) Host Mount (074-0584-xx)
(1) Product and Regulatory Insert (009-1715-xx)
Box Contents
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Cooling 10 CFM
Maximum BTU 51.5 BTU/hr
Power
Input Power 5V DC 3A
Maximum Power 15 watts
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
IMPORTANT! 802.11r (fast roaming) is not
supported
Security WPA™, WPA2™, WPA/wPA2™
Minimum Supported Release
Savant OS da Vinci 8.6
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick ICES-003
FCC ID ASU-SHC2000
IC 10052A-SHC2000
RoHS Compliant
Dimensions and Weights
Height 1.58 in (4.0 cm)
Width 7.86 in (19.9 cm)
Depth 7.65 in (19.4 cm)
Weight Net: 1.3 lb (.58 kg)
Shipping 2.1 lb (0.95 kg)
Rack Space 1U
NONC C / /
G 1 PD
Ethernet RS232-1 RS232-2 -- 4+ +
5-+
6
-1 3 -
+ +2 -+
Audio
Status5VDCReset
C
ABD E GHF
I
Savant® Smart Host with Control 2
Quick Reference Guide

SHC-S2-00 | 009-1775-00 | 181204
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 2
GPIO - General Purpose Input/Output
A two-piece wall mount bracket is included for installation to a wall or
similar. Wall mount instructions are provided below.
Wall Bracket
Control Connections
RS-232 Wiring
IR Wiring (Infrared)
Relay Wiring
– Ensure the all IP emitters
are within 15 feet (4.6
meters) from the control-
lers location.
– Use of 3rd party flashing
IR emitters with Talk
Back is not recom-
mended. These types
of emitters can draw
voltage away from the IR
signal that can degrade
IR performance.
1
IR1
+-+-+-
2
IR2
3
IR3
4 5 6
Use White Stripe
for Positive (+)
Pin 1: IR1 -
Pin 2: IR1 +
Pin 3: IR1 -
Pin 4: IR1 +
Pin 5: IR1 -
Pin 6: IR1 +
– IR connections IR4 to IR6 (not shown in diagram) follow the
same wiring as connections IR1 to IR3.
– GPIO’s configured as an
output can be used to
trigger an action within
the system such as
switching a device.
– GPIO configured as an
input can detect a state
change and trigger a
workflow.
32
1
GPIO 1
Standard
GPIO Using
PD Jumper
Gnd
I/O
PD
Pin 1: GND
Pin 2: GPIO 1
Pin 3: PD (Pull-
down)
– GPIO pins configured as an input are pulled high to (+12V) during
the boot process. To force the GPIO signal low during a boot-up.
Connect the PD pin to the GPIO pin. This forces the GPIO output
to (< 0.8V) during the processor boot times.
– Both Normally Open
and Normally Closed
outputs are available.
32
1
NC NOC / /
Pin 1: NC
Pin 2: Common
Pin 3: NO
1. Attach bracket that mounts to
the bottom of the chassis using
the included M3 x 6mm flat-
head screws.
Host Mount
(074-0584-xx)
2. Attach the wall bracket securely
to the wall. If mounting to dry-
wall, a sturdy anchor such as a
threaded drywall anchor should
be used.
3. Position the Smart Host over
the wall bracket and gently slide
into place. See image to the
right.
Wall Mount
(074-0585-xx)
The optional RCK-3000-xx provides a ventilated shelf for mounting up
to two Smart Hosts. When rack mounting, the wall bracket must not
be installed to allow for a flat, level installation.
Rack
The Smart Host can be installed on a solid, flat, level surface such as
a table, cabinet, or shelf, or can be wall mounted using the included 2
piece bracket. The location should be dry, well ventilated, and out of
direct sunlight. When placing the Smart Host on a flat surface, do not
install the wall bracket. The wall bracket will not allow the Host to lay
flat. Mounting the Host is described below.
Chassis Installation
Refer to the following documents located on the Savant Customer
Community for additional information.
– Savant Smart Host Deployment Guide.
Additional Information
Pin 1: ------ Pin 5: RXD (RS232)
Pin 1 Pin 8
RJ-45 Connector
(Gold Pins Facing Up)
Pin 2: ------ Pin 6: TXD (RS232)
Pin 3: ------ Pin 7: CTS (RS232)
Pin 4: GND (RS232) Pin 8: RTS (RS232)
IMPORTANT!
– Wire colors are included to identify the pins used for this con-
nection. Colors shown do not represent any wiring standard.
– When wiring, DO NOT connect any wires within the cable that
are not required for communications.
– Pins 7 & 8 are only required for CTS/RTS handshaking.
– CTS/RTS handshaking is supported for flow control based on the
profile used in the Blueprint configuration.
– RS-422/485 is not supported
– Refer to the RS-232 Conversion to DB9 and RS-422/485 Pin-out
Application Note on the Savant Customer Community for more
information on RJ-45 to DB9 adapters oered by Savant.
Refreshing the IP Connection
Network Configuration
– Hot Plug the Ethernet (LAN) Connection
– Cycle power
After connecting to a new network, changing routers, or if the IP
Address range in the router was changed, the IP connection should be
refreshed. To refresh the IP connection, do one of the following:
To ensure the IP Address will not change due to a power outage, a
static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.