Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note the power at the fuse board and the luminaire must be switched off before installation or maintenance.
Layout
This track system can be extended to a variety of different configurations using accessories such as left bends,
right bends, T jucntions, X junctions and flexible joints.
Track Accessory:
TJunction
X Junction
Dead End
Bend
108.0mm
35.0mm
35.5mm
79.5mm
294.0mm
35.0mm
35.0mm
108.0mm
108.0mm
35.0mm
16.5mm
183.0mm
183.0mm
35.0mm
35.0mm
108.0mm
183.0mm
40.0mm
40.0mm
43.0mm
35.0mm
182.0mm
1000.0mm
2000.0mm
3000.0mm
35.0mm
• Plan the track layout and and decide accessories needed before fixing anything to the ceiling.
• The maximum power per run of track is 1KW (1000W).
• Mark the first hole position and fit the screw in
position as shown.
• Feed the screw through the keyhole slot, and
slide into position. Mark the position of the
second hole.
• Locate the track and fit the second screw into
position.
• If fitting accessories, remove the end cap, and
push them firmly home. Fit extra lengths of
track as required.
• Ensure the ceiling is capable of holding the weight of the track and products. Take care to avoid damaging any concealed wiring and pipes.
The correct fixings should be used for brick, cavity walls or plasterboard.
Connection
• The track accessories are provided with earth connection points on both sides.
• When offering the accessory to the track, verify which tab needs to be removed.
(See left hand diagram).
• To remove the tab, grasp firmly with a pair of pliers and lever back.
• The tab should snap cleanly off. (See right hand diagram).
• Locate the accessory in the track and push home.
End view of track
Earth Conductor
Remove One or Other Tab
Marked in Grey
Remaining Earth tab needs
to be inserted into Earth
conductor to ensure Earth
continuity.
Wiring
• You have correctly identified the
wires.
• The connections are tight.
• No loose strands have been left
out of the connection block.
Check that...
Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instruction for future reference.
Products:
Undo the screw and remove the cover from the live end.
Push out the desired cable access point. Indentify the
correct cable from the supply and pull through.
Refit the cover onto the live end taking care not to trap
the cable.
Connect the supply wires to the terminal block, opposite
the corresponding wires from the fitting. The central
connector can also be wired in this way.
N
L
N
L
Supply
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current
Building Regulations.
To prevent electrocution switch off at mains supply before installing
or maintaining this fitting. Ensure other persons cannot restore the
electrical supply without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a fused circuit
If replacing an existing fitting, make a careful note of the connections.
This product is suitable for indoor use only, on normal flammable
surfaces.
Only to be installed outside arms reach.
The light source of this luminaire is not replaceable; when the light
source reaches its end of life the whole luminaire shall be replaced.
This track is suitable for dimming. Fittings with low voltage lamps
are not suitable for dimming. Care must be taken to only use the
same type of fitting that is able to be dimmed, and that the dimmer
wattage must not be exceeded.
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
156mm
65mm
Ø54mm
350°
90°
108mm
88mm
