Saxby Lighting Odyssey ST5009BK User manual

Odyssey
ST5009BK - Black
ST5009SS - Stainless Steel
ST5009W - White

Thank you for purchasing this light fitting.
Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Please retain these instructions for future reference.
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
Warning
Specification
Installation
Wiring
Layout
Check That
Commissioning
• Planthedesiredlayoutofthisfittingcarefully,ensuringthecableswillreachthedistancebetweenthejunction
box and the light fitting.
• Avoidlocatinganycablesinpositionsthatwouldcauseahazard.Positioncablesandoutdoorratedjunction
boxes(notsupplied)awayfromareaswheretheymaybeatriskfrombeingcut,trappedordamaged.
• WerecommendthatyouuseH05RN-Fspecificationcable(notsupplied)whichisanoutdoorgrade,rubber
sheathed cable.The mains supply cable must have a minimum cross sectional area of 1.0mm²
• Cablesmustbeprotectedusingsuitableconduitorplastictrunking.
Havingcorrectlyidentifiedthewiringfromyourexistinglightfitting,pullthewirethroughtheholeandconnectto
the connection block inside the product in the following way:
Voltage: 240V50Hza.c.
Lamp: 35WGU10Halogen
IP rating: 44
4. Wraptheterminalblockintape,covering2cmoneachsideoftheconnections.
5. Push terminal block back onto the retaining pegs inside mounting box.
6. Fittheproductbackontothemountingboxandrefitgrubscrews,tightengrubscrewstosecure.
7. Replacefuseorcircuitbreakerandswitchon.Yourlightisnowreadyforuse.
1. Existing fittings must be completely removed
before installation of a new product. Before
removingtheexistingfitting,carefully note
the position of each set of wires.
2. Remove mounting box (A) from product
by removing grub screws (C). Pull terminal
block off of retaining pegs in mounting box.
Carefully pierce a small hole in the rubber
gasket in the centre of the mounting box to
allow the cable to pass through.
3. Thread the cable through the hole and fix the
mounting box to the wall using the screws
and plugs supplied (B). Take care not to
damage any concealed wiring.
A
B
C
108.0mm
63.0mm Dia
92.0mm
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
InstallinaccordancewithIEEWiringregulationsandcurrentBuildingRegulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannotrestoretheelectricalsupplywithoutyourknowledge.Ifyouareinanydoubt,pleaseconsultaqualified
electrician.
Thislightfittingshouldbeconnectedtoacircuitwitha30mARCDfitted.
Ifreplacinganexistingfitting,makeacarefulnoteoftheconnections.
Alwaysusethecorrecttypeandwattagebulb.Neverexceedthewattagestated.
Whenchangingabulb,alwaysswitchoffatthemainsandallowtheoldbulbtocooldownbeforehandling.
Disposeofusedbulbscarefullyandresponsibly.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Checkwithyourlocalauthorityorretailerforrecyclingadvice.
This product is rated at IP44.
This product is not suitable for location in or near a marine or sea environment.
The entire unit gets hot whilst on for a period of time.

Waste electrical products should not be disposed of with household waste. Please recycle where
facilitiesexist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Foryoursafety,alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.
SaxbyLightingLtd.BH233PE
Care and Cleaning
Recycling Advice
Safety Information
The shade must be replaced immediately should the shade become cracked or damaged.This
tting must not be used without the shade in place.
When changing a bulb, always switch off at the mains and allow the bulb to cool
before handling. Disposeofusedbulbscarefully.Useasoftclothtohandlebulbs,avoid
directlytouchingthebulbsasthiswillshortentheirlife.Donotexceedthewattagestated
or use a different shape bulb from that indicated on the fitting.
Bulb type - 35W GU10
1. Unscrewthebezel
2. Removetheoldbulbbyturninganti-clockwise.
3. Insert new bulb.
4. Replacethebezelensuringthatitistightlysecured.
35W GU10
Mains Halogen
Fitting / Replacing Bulbs
Iss.2 06012014
Donotusesolventsorabrasivecleanersasthesecoulddamagethefinish.
Innormalcircumstances,stainlesssteelisveryresistanttocorrosion.Itdoeshoweverrequiremaintenanceto
preservethehighqualityappearance.Washtheproductwithwarmsoapywater,removingallsurfacedeposits.Rinse
withclearwaterandwithasoftcloth,wipedry.
Insomecases,surfacecorrosionmayariseafterinstallation.Thisisnormallycausedbytinyironparticlesleftbehind
after the brushing process when finishing.
Washanddryasdetailedabove.Thenwithasoftclothsoakedwithaprotectiveoil,wipeallover.
Howeveriftheproductissubjecttoextremeenvironmentalconditionssuchasmarinelocations,industrial
pollutionandacidrainthesemaintenanceproceduresshouldbecarriedoutaroundfourtimesayear.Forsevere
corrosion,non-abrasivecreamcleanersorproprietarystainlesssteelcleanersshouldbeusedtoremovethe
corrosion.Washanddryasdetailedabove.Thenwithasoftclothsoakedwithaprotectiveoil,wipeallover.
Glassparts-Removeandwashinwarmwaterorjustuseadampcloth.Donotuseabrasivematerialsasthese
will damage the finish.
Do not clean the units with a pressure washer.