Saxby Lighting Severus EL-40108 Manual

Instruction leaflet
Severus Outdoor Wall
61220, EL-40108
Commissioning
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could
damage the finish.
This light source is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
good quality insulation tape.
Diagram C. Re-fit the led board and the lens housing.
Diagram D. Re-fit the cover plate – click in position.
light is now ready for use.
Fitting/Replacing bulbs
Lens
housing
Diagram C.
Diagram D.
V4 29/11/2020
WWW.saxbylighting.com Saxby lighting. BH17 7BY
Replace Cracked Shade

Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instruction for future reference.
Warning
Specification
Voltage: 240V 50Hz a.c.
Lamp: 3W LED Module (SMD), 3000K
IP rating: 65
Layout
Installation
Wiring
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting, carefully note the position of each set
of wires.
account the entry position of the cable and make
sure there is sufficient cable coming out of the wall
to connect to the terminal block. Ensure that the
mounting surface is solid, preferably a brick or block
wall and ensure that there are no other cables or
pipes beneath the surface.
Diagram A. Gently prise off the cover plate to reveal
the 4 retaining screws on the sides of the unit.
Unscrew these to remove the lens housing.
Diagram B. Unscrew and remove the 4 led board
screws. Bring the mains cable through the rubber
grommet in the wall plate and then use the wall
plate as a template and mark the fixings holes, use
appropriate fixings to secure the back plate to the
wall.
Wire as detailed below.
ensuring the cables will reach the distance between
the junction box and the light fitting.
cause a hazard. Position cables and outdoor rated
junction boxes (not supplied) away from areas
where they may be at risk from being cut, trapped or
damaged.
cable which is an outdoor grade, rubber sheathed
cable. The mains supply cable must have a
minimum cross sectional area of 1.0mm²
plastic trunking.
This light fitting is Double Insulated and
does not require connection to an Earth
circuit.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of
the connections.
This system contains non-replaceable parts and
cannot be serviced. If damage occurs the part should
be scrapped.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is rated at IP65.
This product is suitable for location in or near a
marine environments.
This product is not suitable for dimming.
Having correctly identified the wiring from your light
fitting, connect to the approved outdoor rated external
terminal block in the following way:
Check that...
The connections are tight block.
Reseal the approved outdoor rated external terminal
block.
Cover
plate
Lens
housing
Diagram A.
Gromme
t
Securing
screws
I
ncom
i
ng supp
l
y
W
a
ll
pl
a
t
e
Led board
Diagram B.
SUPPLY
NEUTRAL
SWITCHED LIVE
LIGHTFITTING
BLUE (N)
BROWN (L)