Saxby Lighting Palin Spike Manual

When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of
used bulbs carefully. Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life.
Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
Check with your retailer re bulb dimming capability before purchasing replacement bulbs.
1. Unscrew the bezel
2. Remove the old bulb by turning anti-clockwise.
3. Insert new bulb.
4. Replace the bezel ensuring that it is tightly secured.
Instruction leaflet
Palin Spike
13797, 13914, 75438
For your safety, always power switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish. Do not
use solvents or abrasive cleaners as these could damage the finish.
For 13797 and 13914, in normal circumstances, stainless steel is very resistant to corrosion. It does however
require maintenance to preserve the high quality appearance. Wash the product with warm soapy water, removing all
surface deposits. Rinse with clear water and with a soft cloth, wipe dry.
In some cases, surface corrosion may arise after installation. This is normally caused by tiny iron particles left
behind after the brushing process when finishing.
Wash and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.
However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution
and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion,
non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash
and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.
Do not clean the units with a pressure washer.
Fitting/replacing bulbs (Max. 7W LED GU10)
Care and Cleaning
7W LED GU10
V2 08/01/2022
www.saxbylighting.com Saxby Lighting
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
UK Manufacturer: BH17 7BY
This LED's are protected by the glass shade. The shade part must be replaced immediately should it
become cracked or damaged. This fitting must not be used without the glass shade in place.
Replace Cracked Shade

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of
the connections.
Always use the correct type and wattage bulb. Never
exceed the wattage stated.
This product is suitable for dimming when used with a
dimmable bulb.
When changing a bulb, always switch off at the mains
and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is rated at IP44.
Please note: entire unit gets hot whilst on for a period
of time.
This light fitting should be connected to a 30mA RCD.
This product may require the use of a outdoor rated
connector block.
If the external flexible cable or cord of this lamp is
damaged the lamp must be returned to the service
agent for repair.
Specification
Voltage: 220-240V~ 50Hz
Lamp: 1 x Max. 7W LED GU10
IP rating: 44
Layout
Wiring
on the location, an approved outdoor rated plug and
socket may be required. Alternatively an approved
outdoor rated external terminal block may be used.
cause a hazard. Position cables and connector block
away from areas where they may be at risk from
being cut, trapped or damaged.
underground must be protected using suitable
conduit or plastic trunking.
spike into, and can support the luminaire. Do not
install in very wet or boggy areas.
Plug Wiring
or in an approved outdoor rated enclosure.
supply.
fitted with a 3 amp fuse. Should the fuse require
replacement, it must be replaced with a fuse rated at
3 amp and approved to BS1362.
coloured in accordance with the following code:
Blue – Neutral
Green / Yellow - Earth
Brown – Live
You have correctly identified the wires
The connections are tight
No loose strands have been left out of the connection
block.
Ensure that all cord grips are tightly secured.
Ensure that all seals are re-fitted correctly.
If not fitting to a plug then the product must be wired to
an approved outdoor rated terminal block.
Having correctly identified the wiring from your existing
light fitting, connect to the approved outdoor rated
external terminal block in the following way:
Wiring
Check that...
Commissioning
spike into, and can support the luminaire. Do not
install in very wet or boggy areas. Push the spike into
the ground.
light is now ready for use.
E
L
N
GREEN / YELLOW
Earth
Neutral
Live
Fuse
3 Amps
Cord Clamp
BLUE
BROWN
SUPPLY
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
LIGHTFITTING
BLUE (N)
BROWN (L)
GREEN/YELLOW
This product is not suitable for location in or near a
marine environment.